Trusted HVAC, Plumbing & Electrical Services in Alliance, OH

Conducted free estimate for replacement of existing 40-gallon Whirlpool electric water heater located in basement utility area. Assessed current installation including copper supply piping, electrical connections, and plumbing configuration extending from top of unit. Identified additional issue with non-functioning interior water shut-off valve requiring repair or replacement to enable proper isolation of water supply during future service work. Documented existing conditions including water heater placement, surrounding mechanical systems, HVAC ductwork proximity, and basement environment for accurate proposal preparation.

Responded to service call for non-operational water heater. Upon arrival, inspected Richmond-branded 40-gallon natural gas water heater (Model BC49S-34F3, 34,000 BTU input) manufactured in May 2015. Documented unit specifications including serial number U211625339, maximum working pressure rating of 150 PSI, and AHRI certification. Performed visual assessment of unit condition, plumbing connections including copper piping and brass fittings, blue valve mechanism at base, and overall installation setup in basement utility area. Photographed water heater labels, warning decals, and technical specification plates for service records. Provided free estimate for necessary repairs or replacement options to restore hot water functionality.

Completed installation of Lennox air conditioning system with matching evaporator coil at residential property. Positioned outdoor condenser unit on composite pad with white gravel base against exterior wall with gray horizontal siding. Installed electrical disconnect box on siding and ran conduit from disconnect to unit per code requirements. Ensured proper clearances around equipment for adequate airflow and future service access. System installed as second AC unit for property, tested and confirmed operational upon completion.

Completed routine maintenance on 3-year-old residential air conditioning system. Inspected Lennox furnace unit and control board, verified all electrical connections secure and properly routed, checked circuit board components and wiring harnesses for proper operation. All system components found in good working condition with no issues identified during inspection.

Completed comprehensive tune-up and maintenance on 6-year-old residential HVAC system including both air conditioning and furnace units. Performed full system inspection, verified thermostat operation and calibration as requested, replaced air filter, and documented equipment condition with interior component photography. All components found operating within normal parameters with no issues identified during service visit.

Completed preventive maintenance on 5-year-old cooling system as part of first scheduled call. Performed comprehensive inspection of HVAC equipment, confirmed thermostat operation and settings, checked refrigerant levels, cleaned condenser coils, inspected electrical connections, and verified proper system operation. All components found to be functioning within manufacturer specifications with no repairs required at this time.

Completed annual maintenance on 11-year-old air conditioning system, which included inspection of indoor furnace control board and outdoor condenser unit. Verified all electrical connections, checked control board operation with LED indicators functioning properly, inspected condenser fan assembly and guard for proper operation, and confirmed unit is operating within normal parameters.

Responded to customer concern regarding air conditioning unit cycling on and off frequently. Performed diagnostic temperature measurements at supply and return vents, recording 71.1°F at return and 73°F at supply register. Verified unit is maintaining cooling functionality and achieving adequate temperature differential. System operating as designed with no immediate service concerns identified at time of inspection.

Responded to service call regarding dual tanked water heater venting issue previously identified by gas utility company. Upon arrival, performed comprehensive inspection of both residential water heaters installed in basement mechanical room. Evaluated venting configuration, including overhead piping system, ductwork connections, and exhaust routing. Assessed copper supply lines, flexible connections, and associated plumbing infrastructure connected to both units. Examined proper draft conditions and verified combustion air requirements for safe operation. Documented existing installation with photographic evidence showing dual water heater setup, piping configurations, and current venting arrangement. Provided technical assessment of venting system compliance and recommended corrective measures to ensure proper exhaust ventilation and safe operation of both gas-fired water heating units.

Responded to complaint of intermittent sewer odor in 1917-era residence. Upon inspection, identified potential issues with plumbing venting system and drain trap configurations. Examined basement utility area plumbing stack, including white PVC drain/vent lines and PEX water supply manifold system. Inspected under-sink cabinet plumbing, verifying P-trap assembly and connections for proper seal integrity. Photographed existing plumbing installations showing vertical drain stack with manifold connections and under-cabinet trap configuration with backflow prevention device. Advised homeowner on potential causes of sewer gas infiltration, including dry traps, compromised vent stack, or deteriorated wax ring seals at fixtures. Recommended monitoring situation and provided guidance on maintaining proper trap seals through regular fixture use.

Completed MVP cooling maintenance visit on 12-year-old HVAC system. Performed comprehensive inspection of indoor furnace unit and outdoor condenser unit, verified operational status of all components, checked refrigerant levels, cleaned condenser coils, and documented equipment condition with photographs. System operating within normal parameters upon completion of preventive maintenance service.

Performed preventive maintenance inspection on residential air conditioning system for established customer. Upon examination of indoor evaporator coil assembly, identified moderate to significant rust and corrosion present on metal housing components, corrugated fins, and mounting surfaces, indicating prolonged moisture exposure. Documented deterioration with photographic evidence showing oxidation patterns around connection points and along seams of ductwork. Inspected refrigerant lines, condensate drainage system, and associated mechanical components for proper operation. System functionality verified at time of service visit.

Completed installation of a 90% efficiency furnace and air conditioning system. Installed new electrical components including Littelfuse FLNR 20A fuses with proper wiring connections, established refrigerant line connections with brass service valves, and routed flexible conduit and copper refrigerant lines through the unit compartment. All components tested and operational upon completion.

Completed comprehensive HVAC estimate for full system replacement of existing forced-air furnace and air conditioning equipment in residential basement installation. Evaluated current Dependable brand 92% efficiency furnace unit with existing ductwork configuration, assessed equipment condition and operational status, documented system specifications, and provided replacement recommendations for upgraded heating and cooling system with proper sizing calculations based on home requirements.

Replaced Federal Pacific sub panel in garage with code-compliant panel and corrected improper 3-wire feeder by installing new 4-wire overhead feed from main house to garage peak. Installed two GFCI outlets on rear exterior of home to provide required ground fault protection. Enclosed exposed splice on garage back wall in approved junction box to meet code requirements. Removed existing fluorescent light fixture and installed LED replacement while properly enclosing associated open splice in junction box. All work completed to bring electrical system into compliance with current National Electrical Code standards for sub panel feeders, GFCI protection, and splice enclosures.

Completed MVP cooling maintenance visit on residential air conditioning system. Performed comprehensive inspection of outdoor condensing unit, including internal components such as compressor, refrigerant lines, electrical connections, and housing condition. Documented equipment condition through photographs showing normal operational wear and seasonal debris accumulation, with all major components functioning within acceptable parameters.

Completed MVP cooling maintenance visit on 15-year-old HVAC system. Performed system diagnostics using digital measurement tools, recording airflow readings of 665 CFM at supply register. Inspection revealed significant dust and debris accumulation on vent louvers and visible surface oxidation on ductwork. Observed heat-related discoloration and oxidation patterns on condensate drain pan, indicating extended thermal exposure consistent with system age. Documented equipment condition with photographic evidence for maintenance records.

Responded to service call for bathtub drain obstruction with complete drainage failure. Upon arrival, assessed the fixture and plumbing system, then successfully cleared the clog using appropriate drain cleaning equipment. Restored full drainage function to the bathtub, tested water flow to confirm proper operation, and left the fixture in working condition.

Completed warranty repair by reattaching separated water line sections using copper pipe fittings and connections. Retrieved necessary parts from will call and reinstalled piping infrastructure to restore proper water flow. All connections were secured and tested to ensure leak-free operation of the plumbing system.

Returned to property for callback to address incomplete work from previous service visit. Reconnected copper piping to exterior hose bibs and detached garage that had been inadvertently left disconnected during prior repair. Verified all connections were properly secured and tested water flow to exterior spigots to ensure full system functionality. All plumbing connections in basement utility area now operational with no leaks detected.