Reliable HVAC, Plumbing & Electrical Services in Aurora, OH

Performed scheduled maintenance on MVP furnace system. Inspected copper refrigerant lines and checked for proper condensation drainage. Examined blower motor assembly and control board components, verifying all electrical connections and wire harnesses were secure with no signs of wear or damage.

Performed scheduled MVP furnace maintenance visit, inspecting the basement-installed HVAC system including the main furnace unit and associated ductwork. Examined the ECM drive control board which displayed a "3" code, verified all electrical connections were secure, and confirmed proper operation of all components including the PVC venting system.

Completed routine maintenance on MVP furnace system. Inspected all components including heat exchanger, burners, blower assembly, and refrigerant lines. System appears to be properly installed on wooden supports with appropriate ductwork connections and is functioning within normal parameters.

Performed scheduled heating maintenance visit on residential HVAC system. Inspected air filter housing and confirmed filter is properly installed with no visible damage. Examined gas valve and copper supply lines for proper operation and signs of leakage; all components functioning normally with no issues detected.

Performed comprehensive furnace tune-up service, including inspection of internal components (blower motor, circuit board, electrical connections) and replacement of air filter (20x25x4). System functioning properly with no issues identified.

Responded to service call for furnace making abnormal noise. Upon inspection, found water damage and rust on blower motor housing causing vibration against the frame. Replaced ECM motor and inspected control board for potential electrical issues, confirming proper operation after installation.

Conducted site assessment for generator installation in unfinished basement with existing gas supply. Evaluated utility area containing galvanized ductwork, insulated walls with vapor barrier, and multiple conduit runs. Created detailed layout diagram noting front/back orientation and elevation requirements for proper generator placement.

Performed scheduled MVP Heating maintenance service that was rescheduled from previous date. Inspected control wiring connections and examined evaporator coil, noting dust accumulation and minor oxidation on the aluminum fins. Documented system condition with photographs for service record.

Successfully replaced standard circuit breakers with tandem breakers in the garage electrical panel as confirmed. Parts were ordered and received, with installation completed according to electrical code requirements.

Responded to customer complaint of burning odor throughout home. Inspection revealed dust buildup on heat exchanger causing burn-off during initial seasonal operation. Cleaned heat exchanger, verified proper condensate drainage system function, and confirmed normal furnace operation with no gas leaks.

Diagnosed and serviced Argo electric boiler experiencing heat output issues. Accessed control panel to inspect circuit board and electrical connections. Verified proper terminal connections and system functionality, resolving the heating performance problem.

Performed scheduled heating system maintenance on a residential furnace unit. Conducted thorough inspection of the system components and used hex key tool for necessary adjustments. Service was rescheduled from previous appointment on 12/26.

Inspected leaking humidifier system and identified significant corrosion and mineral buildup on copper pipe connections and central valve assembly. Also examined reported leaky cast iron faucet. Both issues showed advanced deterioration requiring replacement of affected components to resolve water leakage problems.

Accessed wall cavity to diagnose and repair a burst copper water line. Located frost-covered pipe within structural framing, opened drywall for proper access, and completed necessary repairs. Parts were ordered and received for the repair work as specified.

Inspected 12-year-old furnace and found critical crack in primary heat exchanger, requiring full system replacement. Documented existing installation in basement utility room which includes furnace with PVC ventilation pipes, copper line connections, and associated ductwork. Recommended complete HVAC system replacement due to safety concerns with the compromised heat exchanger.

Performed scheduled MVP heating maintenance on 9-year-old system. Inspected furnace unit, ductwork connections, and associated whole-house humidifier. Verified proper operation of control systems including humidifier's digital interface and adjustment mechanisms. All components functioning within normal parameters.

Responded to emergency call for burst pipe in 25-year-old residence. Accessed plumbing through bathroom wall panel behind toilet, identified source of leak, and completed necessary repairs to restore proper water flow and prevent further damage.

Completed installation of a single head mini split system. Installed 20A fuses for proper electrical protection and mounted the outdoor condenser unit on a pad in a narrow alcove between exterior walls. All connections were properly secured and system was tested for operation.

Responded to service call for frozen pipes causing complete water outage in the home. Inspected the water heater (Lochinmar model) and plumbing system in the utility area. Provided customer with professional guidance on safely thawing frozen pipes and proper procedure for restoring water service to prevent potential pipe damage and future freezing issues.

Installed dedicated circuit for mini split system in electrical panel. Removed panel cover to access interior components, connected appropriate gauge wiring to new breaker, and ensured proper termination of all conductors. Verified circuit functionality and reinstalled panel cover upon completion.