HVAC, Plumbing & Electrical Services in Barberton, OH

Performed a scheduled heating maintenance visit, inspecting the furnace control board and low-voltage wiring and verifying connections at the terminal block and connector. Measured gas manifold pressure with a digital manometer, recording approximately 11 inH₂O, and confirmed operation with no visible damage, corrosion, or leaks noted. Recommend securing and rerouting loose wiring and splices to prevent future connection issues.

Performed MVP furnace maintenance, including inspection of the burner assembly, heat exchanger inlets, and gas valve connections, and documented rust, flaking corrosion, and scorching around the burner rims indicating age-related wear. Replaced the pleated return air filter, which showed uneven, bulging pleats, and checked the condensate drain piping and floor drain, noting dampness and staining that warrants monitoring for leaks or drainage restrictions. Recommend follow-up evaluation of the burner and heat exchanger components to ensure continued safe, efficient operation.

Performed scheduled heating maintenance on the gas furnace, including inspection of the gas valve, pressure switch, inducer assembly, and associated wiring and connections. Verified gas manifold and system pressures using a dual-port digital manometer and measured electrical values with a clamp multimeter to confirm proper component operation. No signs of corrosion, damage, or abnormal wear were observed, and the furnace was left operating within normal parameters.

Performed annual maintenance on a 6-year-old gas furnace, including combustion analysis in natural gas mode with readings of 9.9% O2, 6.2% CO2, 15 ppm CO, and 97.0% efficiency, all within acceptable operating ranges. Verified electrical operation with a clamp meter, measuring approximately 120 VAC supply voltage, and confirmed the unit is operating safely and normally with no abnormal conditions observed.

Installed a dedicated circuit for the AC unit, running flexible metal conduit to a galvanized junction box mounted on the joist, with conductors spliced using listed twist-on wire connectors. Routed supply cabling through the basement framing, secured to the underside of the beam with cable staples. Verified connections and confirmed the circuit is properly terminated and ready for operation.

Performed electrical maintenance on the standby generator, including a battery health assessment using a digital battery/CCA tester. Results confirmed the starting battery is in good condition, with 97% state of health, 100% state of charge, 13.34V, and 528A measured against the 540A rated CCA, indicating reliable starting capability.

Performed seasonal heating maintenance on the furnace, including inspection of the integrated control board, wiring harness connections, and terminal fastenings, with all connections found secure and properly routed. Removed and inspected the flame sensor/ignition electrode rod, confirming no cracking or major damage to the ceramic insulator, and noted light surface oxidation on the rod consistent with normal wear. Observed minor rust spotting on the control panel and verified flue pipe and sealant details per installation guidelines.

Performed a replacement estimate on a 40+ year-old furnace with a no-heat condition; unit is obsolete and replacement parts are unavailable. Inspected the basement installation, including the furnace, flue/vent piping, ductwork, and adjacent water heater, and documented existing conditions with photos. Recommended full furnace replacement.

Responded to a no-heat call on a 41+ year old basement furnace and inspected the blower/motor compartment, finding the motor, wiring, and cabinet heavily coated with dust, dirt, and cobwebs. Evaluated the blower motor, wiring, and cabinet condition to diagnose the loss of heat, noting the unit's advanced age and deteriorated condition.

Performed annual heating maintenance on a 5-year-old furnace, including inspection and cleaning of the hot surface ignitor assembly and flame sensing components. Inspected the blower wheel and housing, removed accumulated dust and debris from the blades, and verified secure motor shaft and set screw. Checked the PVC flue/vent connection and rubber coupling, noting minor discoloration at the pipe base, and confirmed secure fasteners and proper operation of the unit.

Performed seasonal heating maintenance on a 5-year-old gas furnace, inspecting the blower assembly, control board, transformer, and low-voltage wiring, and found all components intact with no visible damage, corrosion, or frost. Verified the condensate drain line connection and checked the cabinet interior, noting loose low-voltage wiring in the lower cabinet and dust accumulation. Unit is in good working condition.

Performed scheduled maintenance on a Generac standby generator, removing the top and side access panels to inspect the interior components, including the battery, terminal connections, and enclosure. Verified the unit was clean, intact, and free of visible damage, with the flexible conduit connection to the structure and the controller indicator in normal condition.

Responded to a no-heat call on a Lennox gas furnace over 30 years old, accessed the control compartment, and performed electrical diagnostics with a clamp meter on the contactor/relay, wiring, and associated components to identify the cause of the heat failure. Unit is well past its expected service life, with heavy dust and grime buildup on the cabinet and ductwork and corroded, aged piping and insulation noted; replacement should be considered.

Inspected the gas fireplace supply and located the branch line with its shutoff valve in the joist space below the fireplace. Verified the gas supply path and valve position to the log set and burner, confirmed the control module and burner assembly were intact, and restored gas flow to the fireplace.

Performed seasonal heating maintenance on a Lennox gas furnace, including inspection of the blower compartment, control board, and low-voltage wiring, and noted heavy dust and lint accumulation at the filter slot and cabinet floor. Inspected the PVC combustion air and venting assembly and observed orange-brown staining on the floor beneath the unit, indicating prior moisture or rust residue that should be monitored for leaks or condensate drainage issues. Unit was left operational, with recommendations for filter replacement and cabinet cleaning.

Responded to a report of a 4-5 year old sump pump short-cycling, turning on and off every couple of minutes. Marked underground utilities in the work area and staged discharge piping components on site. Inspected the pump system and discharge line to diagnose the cycling condition.

Performed a 100A electrical service upgrade, including installation of an exterior service disconnect and updated grounding electrode system to meet 2023 National Electrical Code requirements. Excavated and installed new ground rod(s) with proper bonding and connections, and verified the completed installation for code-compliant operation.

Replaced the failed toilet supply shut-off valve that had broken off, restoring a functional isolation point at the water supply line. Inspected the tank and installed new toilet repair components, including a flush valve assembly, flapper, and handle, to address the worn internal parts and discolored, stained tank conditions. Verified the supply connection was leak-free and confirmed proper fill and flush operation.

Removed the existing toilet and installed a customer-supplied American Standard Edgemere toilet. The closet flange showed heavy rust and scale buildup, and the finished installation was left clean and operational with no additional parts required.

Performed a complete furnace tune-up, including inspection and testing of components and verification of safe, proper operation. Inspected the whole-house humidifier and found the evaporator pad showing mineral buildup and discoloration, with the unit's drain line and housing in place. Completed the maintenance membership renewal.