Removed cracked ABS fitting and surrounding drain pipe from the main stack. Installed new ABS piping with two no-hub fittings to tie into the main stack, along with a new 3"x1½" sanitary tee. Ran new drain piping through the wall cavity to the back bathroom vanity location and stubbed out piping at the wall for vanity connection.

Responded to service call for broken outdoor water spigot with water shut off to the property. Successfully replaced the failed exterior spigot and restored water service to the residence. Additionally inspected and addressed concerns with an interior faucet as requested by the customer.

Installed a dedicated 20-amp circuit to power a new 1500-watt electric fireplace unit. Ran romex wiring across the basement through floor joists to the fireplace location, installed a junction box below the fireplace to convert to MC cable, and drilled a penetration to the left of the existing gas line. Fished MC cable up through the existing coal chute, drilled through the brick backing inside the fireplace, and installed a surface-mount receptacle in the rear of the fireplace cavity to provide power for the new electric unit.

Responded to water leak issue affecting multiple baseboard heating units supplied by aging 16+ year old boiler system. Upon inspection, found active leaks at several baseboard connections requiring immediate shutdown of boiler to prevent further water damage. Documented existing hydronic heating system configuration including expansion tank, circulator pump, zone valves, and copper piping network showing significant age-related corrosion and oxidation throughout. System remains offline pending customer decision on repair versus replacement options given the advanced age of equipment and extent of deterioration observed in piping components.

Responded to complaint of gurgling noises and odors emanating from garage sink drain when kitchen sink was in use. Conducted inspection of drainage system and plumbing connections in garage area. Upon examination, identified improper venting or potential partial blockage in shared drain line causing air pressure issues between fixtures. Documented existing plumbing configuration including exposed drain lines and mechanical systems for service records. Explained to customer that gurgling sounds indicate negative air pressure in the drain system, typically caused by inadequate venting or restriction in the common waste line. Recommended follow-up evaluation of vent stack and potential drain line cleaning to resolve cross-fixture drainage issues and eliminate odor problems.

Responded to water leak originating from upstairs toilet with visible damage in basement area. Upon arrival, accessed crawl space to inspect plumbing infrastructure serving second-floor bathroom. Located source of leak at toilet supply line connection. Identified compromised pipe fitting allowing water to travel through floor joists into basement ceiling area. Secured water supply, replaced faulty connection with proper fitting, and tested system under pressure to verify repair integrity. No further leakage detected upon completion of pressure test.

Completed scheduled MVP heating maintenance visit. Performed comprehensive system inspection of furnace unit, including examination of blower wheel assembly which showed proper blade alignment and clean operation. Verified all ductwork connections, condensate drainage system, and humidifier components were functioning correctly with no issues identified.

Completed comprehensive heating maintenance inspection on residential HVAC system. Examined and documented blower motor assembly, verified proper operation of sight glass moisture indicators on refrigerant lines showing clear liquid levels, and inspected copper line connections for integrity. All components found to be functioning within normal parameters with no immediate service needs identified.

Performed routine tanked water heater flush and maintenance inspection. Drained sediment buildup from tank bottom through drain valve, flushed system with fresh water until discharge ran clear, and verified proper operation of temperature/pressure relief valve. Unit showed normal condensation on exterior surface consistent with recent hot water usage, all components functioning within manufacturer specifications with no leaks or operational concerns detected.

Installed battery backup sump pump system to complement existing one-year-old primary pump. System includes backup pump unit, battery power supply with monitoring capabilities, and properly configured discharge piping integrated with existing PVC discharge line. All electrical connections completed, monitoring panel mounted and programmed, and system tested to ensure automatic activation during primary pump failure or power outage scenarios.

Completed scheduled MVP heating maintenance visit. Performed comprehensive system inspection with access panel removal, documenting internal components including blower motor assembly, control board, electrical connections, and ductwork. All wiring, connections, and mechanical components verified to be in proper operating condition with no visible wear or damage requiring immediate attention.

Completed MVP recurring cooling and heating maintenance visit. Inspected and photographed HVAC system components including copper refrigerant lines, electrical fuse assembly (Edison ECNR15 dual-element class RK1), rooftop unit with parallel refrigeration tubing, control panel with circuit breakers, and associated wiring connections. All equipment operational with normal wear patterns observed; system functioning within specifications.

Completed MVP furnace maintenance on residential heating system. Performed comprehensive system inspection and diagnostics using digital multimeter to verify proper electrical readings and system performance. Measured and documented amperage draw at 8.109 amps, confirming unit is operating within manufacturer specifications. Inspected pressure switch assembly, including tubing connections and diaphragm components, ensuring proper operation for safe furnace cycling. Examined gas valve, burner assembly, and ignition components for proper function. Verified all wiring connections, including control board circuits and safety switches. Checked condensate drainage system including PVC piping and trap assembly. All components found to be functioning correctly with no immediate repairs required. System tested and left in proper working order.

Completed comprehensive furnace tune-up including inspection of blower motor assembly, control board, and all electrical connections. Verified proper operation of all system components, checked wiring harnesses and safety controls, and confirmed unit is functioning within manufacturer specifications.

Completed preventive maintenance cooling service on 3-year-old electric furnace system with integrated cooling capabilities. Performed comprehensive inspection of HVAC equipment including furnace unit, ductwork connections, control board components, and all system connections. Verified proper operation of DIP switch settings on control board, checked all electrical connections and terminal blocks, and confirmed outdoor interchange jumper configurations were properly set. System tested and operating within normal parameters with no issues found or repairs required.

Responded to service call for 5-year-old furnace displaying 5 red flash error code. Upon inspection, found air filter had been partially drawn into the blower compartment due to negative pressure, causing deformation and restricted airflow. Removed damaged filter and inspected blower assembly and internal components for debris accumulation. Performed thorough cleaning of blower motor, blower wheel, and cabinet interior to remove dust and particulate buildup. Cleared all obstructions from air pathway and verified proper airflow through the system. Inspected control board connections and electrical components for proper operation. Reset error code and cycled unit to confirm normal operation. Advised on proper filter installation and recommended regular filter replacement to prevent future airflow restriction issues.

Completed comprehensive cooling maintenance on 8-year-old air conditioning system and furnace. Inspected and photographed air filter showing standard diamond-pattern mesh construction, verified evaporator coil assembly with serpentine refrigerant lines and finned heat exchanger, and documented system components including refrigerant piping with brass fittings. All maintenance procedures performed according to manufacturer specifications with unit operating within normal parameters.

Completed scheduled MVP heating maintenance visit. Performed system diagnostics including electrical testing with multimeter to verify proper resistance readings and electrical continuity. Inspected and serviced gas valve assembly, checking wire connections and ensuring proper operation of the heating system components. Verified all electrical connections including the white connector harness with red and white wiring. Brought replacement filter as backup in case customer-purchased filter was incorrect size or specification.

Completed scheduled recurring maintenance on dual HVAC systems, ages 5 and 6 years. Performed comprehensive inspection of control boards, electrical connections, blower assembly, and all major components. Verified proper operation of both heating and cooling systems, confirmed all connections secure, and documented equipment condition with photos.

Completed comprehensive tune-up and safety inspection on two furnace units. Performed visual inspection of electrical connections, control boards, and wiring systems; verified proper operation of all safety controls and heating components; cleaned and tested both units to ensure optimal performance for the heating season.