Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Completed maintenance inspection on 1-year-old heat pump system per MVP agreement. Customer reported excessive noise during operation. Upon arrival, performed standard cooling season maintenance protocol including visual inspection of outdoor unit. Examined condenser coil and found moderate accumulation of dirt, dust, and debris on fins, with visible discoloration indicating environmental exposure. Noted debris buildup at base of unit near foundation level. Assessed unit operation and confirmed noise concern. Documented equipment condition with photos showing exterior unit placement, condenser coil condition, and debris accumulation. System operational at time of inspection.

Responded to a boiler service call for a leaking pressure relief valve that was discharging water during heating system operation. Inspected the boiler system, expansion tank, and associated piping in the mechanical room, identifying the faulty pressure relief valve and verifying proper system pressurization. Documented existing conditions of the aging copper piping system and pressure control components for service records.

Completed furnace replacement estimate for residential HVAC system. Evaluated existing York Diamond 80 furnace installation in basement utility area, documented current equipment configuration including PVC venting connections, ductwork interface, and proximity to water heating equipment. Photographed unit specifications, ventilation components, and mechanical room layout to provide comprehensive assessment for replacement options.

Conducted on-site assessment for mini split installation in enclosed patio/sunroom with vaulted beadboard ceiling and wood-paneled walls. Evaluated space layout, electrical requirements, and optimal placement for indoor air handler and outdoor condenser unit to provide efficient climate control for the three-season room.

Replaced two deteriorated shut-off valves in bathroom plumbing system. The existing valves showed significant corrosion and rust, compromising their functionality and reliability. Installed new wheel-style shut-off valves on vertical supply lines to restore proper water control and prevent potential leaks. Work completed in utility access area beneath bathroom fixtures.

Completed MVP backflow prevention test on system up to 2" in size per regulatory requirements. Tested backflow assembly mounted on exterior brick wall, verified proper operation of check valves and relief valve, and documented water meter readings. All components passed inspection and system is functioning within acceptable parameters for cross-connection control.

Replaced existing chandelier with a six-arm brushed nickel fixture featuring candle-style bulbs in residential room. Installed ceiling fan with integrated light fixture and dark wooden blades into builder-wired junction box in separate room, ensuring proper mounting and electrical connections for both fixtures.

Responded to intermittent power loss affecting kitchen microwave and stove circuits. Upon inspection, discovered severe corrosion and rust on electrical terminal block connections serving these appliances. Corroded terminals were creating poor contact and intermittent power delivery, posing a potential fire hazard. Replaced damaged terminal block, cleaned and secured all wire connections, and verified proper power supply to both appliances to eliminate the intermittent fault condition.

Responded to emergency water leak call for 52-year-old HVAC system with condenser and air handler located in attic space. Upon arrival, accessed attic-mounted equipment and performed thorough inspection of air handler, condensate drain system, and associated piping. Identified active water leak originating from primary drain line connection at air handler, which had caused water damage to living room ceiling below. Cleared clogged condensate drain line, repaired loose drain connection, and verified proper drainage flow. Inspected evaporator coil and drain pan for additional issues, finding drain pan showed signs of age-related deterioration. Tested system operation and monitored for proper condensate removal. Documented equipment condition with photos showing outdoor condenser unit and internal components including capacitor and wiring connections. Advised that system age and attic installation may require future maintenance attention, particularly regarding condensate management and p

Opened wall to access existing washer box and replaced it with a similar recessed outlet box model. Installed new brass shut-off valves with dual hot and cold water connections and connected flexible stainless steel braided supply lines. Protected work area with plastic sheeting and painter's tape throughout the installation process.

Performed comprehensive cooling season tune-up and maintenance on 6-year-old Lennox air conditioning system. Completed full system inspection, cleaning, and performance testing of outdoor condensing unit, verified proper refrigerant levels, checked electrical connections, and documented equipment condition with photos showing unit in operational status on concrete pad with adequate clearance from structure.

Completed installation of new air conditioning system with evaporator coil for mobile home application. Installed outdoor condensing unit on prepared rock bed with proper clearances, ran refrigerant lines and electrical conduit up exterior wall to weatherproof disconnect box, and replaced fused disconnect with 20-amp fuses. System tested and operational upon completion.

Responded to no-cool complaint on residential split system. Upon arrival, performed diagnostic inspection of indoor air handler and outdoor condensing unit. Verified system age and conducted visual inspection of both components. Indoor unit showed normal condition with no visible damage or environmental concerns. Outdoor condenser unit displayed typical weathering consistent with age but appeared structurally sound with intact grille and housing. Completed standard diagnostic procedures to identify cause of system failure and determine appropriate corrective action to restore cooling operation.

Completed comprehensive tune-up on York Diamond 80 furnace system, including inspection of all mechanical components, burner assembly, blower motors, and actuators. Customer rescheduled appointment from original date; all standard maintenance procedures performed and unit operating within manufacturer specifications.

Performed complimentary first-year descaling service on Navien NPE-240A2 natural gas tankless water heater per manufacturer warranty requirements. Completed flush and fill procedure using descaling solution to remove mineral buildup from heat exchanger, ensuring optimal efficiency and performance of the instantaneous water heating system.

Completed comprehensive preventive maintenance tune-up on residential outdoor condensing unit. Performed system inspection, verified electrical connections at disconnect box, checked refrigerant line insulation integrity, and confirmed proper unit operation with all components functioning within normal parameters.

Completed installation of Lennox air conditioning system including outdoor condensing unit and indoor evaporator coil with air handler. Installed outdoor condenser on concrete pad with proper clearances from structure, established refrigerant line connections using copper tubing, and completed electrical wiring with disconnect box mounted to exterior wall. Interior installation included mounting air handler unit in utility room, connecting supply and return ductwork, installing condensate drain lines with PVC piping, and making all necessary refrigerant line connections between indoor and outdoor components. Verified all electrical connections, tested system operation, and confirmed proper drainage.

Completed comprehensive furnace tune-up including inspection of air handler unit, control board functionality verification, and ductwork connection assessment. All electrical connections, wiring harnesses, and safety controls were examined and found to be secure and operating within specifications. System tested successfully with no deficiencies noted.

Conducted on-site electrical assessment for standby generator installation. Evaluated existing electrical infrastructure including main service panel capacity, available circuit breaker positions, and current electrical load distribution. Documented gas meter location and utility connections in basement area to determine optimal generator placement and fuel supply routing. Photographed electrical panel configuration showing circuit layout and available capacity for generator transfer switch integration. Assessment completed to provide comprehensive estimate for generator system installation including required electrical upgrades and transfer switch specifications.

Responded to service call for water leaks under kitchen sink and at exterior spigots. Inspected under-sink plumbing assembly including PVC P-trap configuration, compression fittings, and garbage disposal unit connections. Identified leak sources at drain connections and addressed failing seals. Tightened compression fittings and replaced deteriorated gaskets as needed. Checked exterior hose bibs for leaks and performed necessary repairs to stop water loss. Documented existing water filtration system during inspection. All leak points were successfully repaired and tested for proper operation.