Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Replaced two corroded FIP angle stop shut-off valves and supply lines in basement half bath, including a hot water shut-off valve that was actively dripping. All new components were installed and tested for proper operation with no leaks detected.

# HVAC Maintenance - Cooling Service Completed Performed comprehensive preventive maintenance on residential split-system air conditioning unit. Inspected indoor Lennox furnace with integrated cooling coil in basement mechanical room and outdoor condenser unit. Conducted complete system evaluation including refrigerant line inspection, electrical connections verification, and airflow assessment. All components found operating within normal parameters. System tested and confirmed functioning properly for cooling season.

# Main Drain Cleanout Service Report Responded to callback for recently installed main drain backing up with mud and sediment. Upon arrival, found floor drain with significant accumulation of sand, dirt, and debris around the drain opening and on surrounding concrete surface. This issue was related to a previous floor drain replacement that had been installed under concrete. Inspected the white PVC drainage lines connected to the black floor drain assembly and verified structural integrity of the piping system. The backup appeared to be caused by sediment infiltration into the newly installed drain system. Assessed the grated drain cover and surrounding area for proper installation and potential entry points for debris. Documented conditions with photographs showing the extent of sediment accumulation and moisture patterns on the concrete floor surface indicating recent drainage activity. Cleaned out accumulated mud and dirt from the drain area and verified proper drainage flow thro

# Service Summary Completed routine A/C tune-up on 3-year-old residential condensing unit per promotional service request. Performed standard maintenance protocol including system inspection, coil cleaning, and operational testing. Unit found in serviceable condition with minor cosmetic corrosion on top grille; all mechanical components functioning within normal parameters and refrigerant levels adequate for continued operation.

Provided comprehensive HVAC system replacement estimate for 20-year-old furnace and air conditioning unit. Customer expressed interest in promotional offer for air conditioning replacement. Documented existing equipment configuration including furnace installation in basement mechanical room and ductwork system, photographed current system components and layout for proposal specifications.

Responded to service call for 1-year-old furnace not heating upstairs area. Upon inspection, discovered significant ceiling damage in utility space with charred wooden beams, water damage, and accumulated debris in ceiling opening. Identified this structural damage as the source of heat loss affecting upstairs temperature regulation.

Successfully installed 18kW generator system with 150A service. Ran 18' gas line from home to generator location and completed all necessary electrical connections, including panel modifications and conduit installation. System was properly staged, installed, and tested for operation.

Completed comprehensive duct cleaning service using MVP system on residential HVAC ductwork. Inspection revealed significant accumulation of dust, lint and possible mold growth throughout the ventilation system, with debris buildup measuring several millimeters thick in some areas. Successfully cleaned and sanitized all ducts, removing obstructions and restoring proper airflow to improve indoor air quality and system efficiency.

Performed comprehensive gas leak investigation in response to customer-reported odor. Conducted pressure test on existing gas lines and inspected exposed piping in unfinished areas, including basement utility space with copper lines and wall cavity with PVC piping. No active leaks detected; provided customer with quote for requested gas line relocation for kitchen stove as discussed with on-site contractor.

Performed routine maintenance on 3-year-old gas furnace including inspection of electrical connections and gas line fittings. Assessed ductwork condition and recommended professional duct cleaning to improve system efficiency and indoor air quality.

Successfully installed a 90% efficient Trane furnace with proper venting using PVC exhaust and intake piping. System includes a condensate pump to manage water discharge. All connections were verified and temperature differential testing was performed to confirm proper operation.

Performed routine maintenance on heat pump system as part of recurring MVP Heating Visit service. Inspected outdoor condensing unit, checking electrical connections and control board wiring. Examined condenser fan, cooling fins, and refrigerant lines for proper operation and condition.

Diagnosed and repaired inoperative thermostat which was preventing heat call to furnace. Inspected system components and connections, verifying proper operation after repair. System is now functioning as designed with normal heating cycle confirmed.

Performed diagnostic assessment on 24kW Generac residential backup generator experiencing connectivity issues. Inspected the communication module and signal strength, determining intermittent connectivity was not related to customer's WiFi network as initially suspected. Reconfigured monitoring settings and reset communication protocols to restore stable remote monitoring functionality.

Performed scheduled maintenance on Generac standby generator that failed to activate during recent power outage. Inspected internal engine components and control panel connections, then tested the automatic transfer switch functionality. Identified and resolved ignition timing issue, confirming proper operation through simulation test.

Completed scheduled furnace tune-up service, inspecting interior components and heat exchanger which showed oxidation on metal connections. Examined and cleaned blower wheel assembly, which was found to be in good working condition with no debris accumulation between the fan blades.

Performed inspection of 26-year-old 50-gallon gas water heater exhibiting significant leakage throughout unit. Photos documented aged unit installed against basement cinder block wall with copper supply lines and metal vent piping. Provided estimate for complete replacement system including new water heater, required code-compliant connections, and proper disposal of existing unit.

Performed scheduled maintenance on 10-year-old heating system. Inspected electrical control module and PCB connections, noting all wires were properly secured and in good condition. Examined blower wheel assembly which showed normal dust accumulation; cleaned fins to ensure optimal airflow and system efficiency.

Performed complimentary cooling system maintenance for MVP member. Inspected circuit board connections and wiring in air handler, finding all components properly connected. Noted significant dirt accumulation on air filter with visible orange-brown staining, indicating filter replacement is needed for optimal system performance.

Completed kitchen drain line replacement, removing old galvanized and cast iron piping. Installed new basket strainer, tubular dishwasher tailpiece and trap, then ran new 2" PVC piping with air admittance valve for proper venting. All new piping was properly secured to joists and connected to existing PVC drain line.