Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Performed routine maintenance on 7-year-old Lennox gas furnace, inspecting key components for proper operation. Examined system connections including the quarter-turn gas shut-off valve, confirming proper installation and functionality. Assessed ductwork condition and recommended professional cleaning service to improve system efficiency.

Inspected reported bathtub leak at return service call. Checked exterior water pressure gauge showing 80-90 PSI (exceeding recommended residential levels). Adjusted pressure regulator to prevent excessive pressure causing fixture leaks.

Performed diagnostic assessment on tanked water heater due to no hot water supply throughout residence. Replaced faucet fixture in half bathroom sink and installed new wax seal on master bathroom toilet to resolve leak. All systems tested and functioning properly after service completion.

Replaced defective mixing valve cartridge in high-end shower system featuring multiple body sprays and handheld shower attachment. Removed old cartridge, installed customer-provided replacement part, and verified proper water temperature control and operation of all shower components. System now functioning correctly with no leaks observed.

Conducted comprehensive camera inspection of floor drain system in basement utility area. Identified significant debris accumulation around drain grate and documented presence of white powdery material (possible insulation) scattered across concrete floor. Visual inspection also revealed deterioration of drainage components and potential ventilation system issues associated with the nearby HVAC equipment.

Confirmed electrical wiring update quote with customer. Performed inspection of electrical panel, which revealed approximately 20 circuit breakers in good working condition with proper labeling. Service completed as quoted, with photographs taken of the breaker panel and access area for documentation.

Performed routine cooling maintenance on 1.5-year-old HVAC system for MVP member. Inspected heat exchanger fins and found them in good condition with no visible damage. Examined refrigerant lines, electrical connections, and system components which appeared operational with normal dust accumulation but no significant corrosion or damage.

Completed preventative maintenance on 2-year-old furnace. Inspected PVC drainage system, galvanized ductwork, and filtration components - all in good working condition. Checked Aprilaire control panel functionality; display and indicator lights operating normally with proper wire connections.

Performed scheduled duct inspection to evaluate system condition and suitability for cleaning. Utilized specialized probing tool to access and examine ductwork integrity at connection points, identifying minor wear but overall satisfactory condition.

Performed scheduled MVP heating maintenance on 2-year-old system. Inspected and documented basement plumbing and ductwork configuration. Replaced air filter which showed normal accumulation of particulates, ensuring proper system airflow for optimal performance.

Conducted scheduled heating maintenance visit for MVP customer. Inspected ignition assembly components and performed combustion analysis using digital analyzer, confirming proper system operation with readings within acceptable parameters. All diagnostic tests completed successfully with photographic documentation of components and test results.

Performed scheduled furnace tune-up, inspecting system components and operation. Noted significant dust accumulation on blower wheel requiring cleaning to improve airflow efficiency. Utilized hex key tool to access and service internal components during maintenance procedure.

Responded to no-water service call at multi-unit building with 3 hot water tanks and boiler system. Inspection revealed significant water damage and fire/smoke damage to the basement utility area, with compromised plumbing fixtures including a main valve with an orange warning label. Identified and repaired faulty pressure regulator valve that was preventing water flow to the building.

Conducted comprehensive electrical inspection of commercial property with focus on car charging station infrastructure. Documented existing electrical systems through photographic assessment of both exterior and interior spaces, including ceiling-mounted fixtures and available power distribution points. All inspection requirements from provided checklist were completed and documented according to specifications.

Responded to a no-water service call at a multi-unit building with 3 hot water heaters and a boiler. Inspection revealed significant water damage to structural wood elements with visible deterioration and mold formation. Documented extensive damage to the plumbing system including corroded copper and PVC pipes. Also inspected the pressure regulation system which showed signs of leakage at the regulator/valve assembly and possible issues with the flow control mechanism.

Completed routine MVP Heating Service including inspection of plumbing connections and examination of control board circuitry. Documented aging pipe joints with visible wear and verified proper wire connections on the electrical control panel, ensuring all components remain in functional operating condition.

Diagnosed and repaired a non-functioning basement light fixture in a 20-year-old residence. Inspection of the electrical panel revealed loose connections at the breaker, which were properly secured and tested with a multimeter to verify circuit integrity and proper voltage.

Responded to service call for suspected broken drain pipe beneath concrete in 70-year-old residence. Upon inspection of basement utility area, conducted thorough assessment of the plumbing system including cast iron drain pipes and connections. Identified source of issue at junction point where deterioration had occurred due to age, creating subsurface leakage affecting foundation. Implemented repair solution using appropriate materials compatible with existing plumbing infrastructure.

Responded to no-heat call for residential gas furnace. Upon inspection, found faulty flame sensor preventing ignition sequence completion. Cleaned flame sensor using emery cloth to remove carbon buildup, verified proper ignition sequence, and confirmed normal operation through complete heating cycle. System now functioning correctly with proper flame detection.

Performed routine maintenance and tune-up service on 1.5-year-old furnace. Inspected blower wheel assembly for proper operation, noting good condition with no visible damage or debris accumulation. Examined internal components including motor, wiring harnesses, gas valve, control module, and circuit board connections - all functioning within normal parameters. System is operating efficiently with no issues identified.