Heating, Air Conditioning, Electric & Plumbing Services in Cleveland, OH

Performed seasonal heating maintenance on an 8-year-old gas furnace, inspecting the blower motor and housing, gas valve, burner assembly, wiring connections, and control board, with no rust, frost, or visible damage found. Also verified operation of the Aprilaire humidifier control, which displayed a normal humidity reading of 57%.

Installed a new 80% AFUE gas furnace and matching split-system air conditioning unit as a complete system replacement. The furnace was set in the basement utility area and connected to the existing supply plenum and galvanized trunk ductwork, with the flue vent, condensate drain, and gas supply connected. The outdoor condenser was set on its pad and tied to the indoor coil with refrigerant lines and brazed connections, with the system charged with R-454B (A2L) refrigerant and the suction line insulated.

Performed cooling maintenance on two units, including inspection of the Lennox outdoor condenser (intact, clean, with no visible damage, frost, or corrosion) and the indoor air handler cabinet. Noted moisture staining and water residue on the air handler drain pan, indicating possible condensate leakage, along with a loose control wire and accumulated dust and debris at the control board; recommend condensate drain line and pan evaluation and securing of wiring to prevent further moisture-related issues.

Installed a dedicated electrical circuit for a power vent water heater, running new cable to a mounted junction box and making secure wire connections in the utility space. Routed and secured the wiring clear of the insulated piping and verified the circuit was properly terminated and ready for the water heater connection.

Installed a new Lennox condenser on a level pad beside the exterior wall, with line-voltage whip run from the disconnect to the unit. Replaced the 20A cartridge fuses in the disconnect and confirmed the electrical connections were secure.

Performed a seasonal heating maintenance inspection on the natural gas furnace, including inspection of the blower wheel and housing, which showed light dust accumulation and minor surface wear. Conducted a combustion analysis with a flue gas analyzer, recording O₂ at 5.7%, CO at 85 ppm, CO₂ at 8.6%, and steady-state efficiency of 83.5%. System operation was verified following the inspection.

Installed and commissioned a new 80% AFUE gas furnace as the second unit on this job, completing the equipment setup and verifying proper operation. Installed an Aprilaire digital thermostat for system control and a Kidde carbon monoxide alarm for combustion safety, with the manufacturer's warranty documentation provided.

Installed new residential subpanel in utility area with proper grounding and bonding connections. Ran 10/2 and 12/2 Romex wiring through exposed ceiling joists to supply dedicated AC circuit and additional branch circuits as required. Terminated all conductors per NEC standards, verified proper panel labeling, and ensured all circuit breakers were correctly sized for connected loads.

# Attic Rewiring Assessment Conducted comprehensive attic inspection to evaluate existing electrical infrastructure and provide detailed rewiring quote. Assessed exposed wooden framing structure with existing white electrical wiring running through wall studs and joists. Examined current wire routing through vertical studs and horizontal cross-members, noting installation challenges due to insulation materials and confined workspace conditions. Documented structural framework including wooden beams, masonry elements, and mechanical components that will impact rewiring scope. Evaluated access points, clearances, and potential obstruction from ductwork and vapor barriers. Photographed existing conditions including wire placement, mounting brackets, and framing configuration to develop accurate material and labor estimates for complete attic electrical system upgrade.

Completed comprehensive furnace maintenance including inspection of heat exchanger assembly, gas valve connections, and burner components. Performed diagnostic testing of electrical systems using digital multimeter to verify proper voltage readings and system operation, confirming all components functioning within manufacturer specifications.

Conducted comprehensive HVAC system evaluation for furnace and air conditioning replacement in residential property. Documented existing equipment configuration including basement-installed ductwork system with galvanized metal construction, horizontal trunk line penetrating foundation wall, and current mechanical room layout. Assessed ductwork condition, clearances, and structural considerations for new equipment installation. Provided replacement options and recommendations to homeowner's family members who manage the property.

Completed comprehensive MVP heating maintenance on residential HVAC system. Performed thorough inspection of gas furnace components including gas valve assembly, blower motor housing, electrical connections, and control wiring. Verified proper operation of all safety controls and replaced faulty flame sensor to ensure reliable ignition and system performance. All components tested and confirmed operational, with system returning to full heating capacity.

Completed comprehensive maintenance service on gas-powered furnace system including inspection of blower motor assembly, electrical connections, and all associated components. All systems tested and verified operational, with blower motor showing proper function and secure wire connections across all control circuits.

Performed comprehensive furnace tune-up and cleaning on residential heating unit of unknown age. Conducted thorough inspection of all internal components including blower motor assembly, draft inducer, burner assembly, gas valve, flame sensors, and electrical connections. Cleaned combustion chamber and removed dust accumulation from mechanical components. Verified proper operation of all safety controls, sensors, and switches. Inspected wiring harnesses and electrical connections for signs of wear or damage. Noted significant rust and corrosion present on burner assembly components, which will require monitoring for future replacement consideration. All components tested and confirmed operational at time of service completion.

Performed annual preventative maintenance on 2-year-old generator unit per manufacturer specifications. Customer reported red warning light illuminated on control panel prior to service. Conducted comprehensive system diagnostics using digital multimeter to test voltage output, electrical connections, and control circuits. Inspected all major components including engine, alternator, transfer switch, and battery system. Verified proper operation of all safety features and warning indicators, addressed red light alert condition, and confirmed unit returned to normal operational status with all systems functioning within acceptable parameters.

Completed comprehensive HVAC system evaluation for both furnace and air conditioning replacement at residential property. Assessed existing equipment located in basement utility area, documented current mechanical systems including ductwork configuration, electrical service panels, and venting infrastructure. Provided replacement options and equipment recommendations to homeowner in consultative manner per customer's preference for low-pressure sales approach.

Conducted comprehensive assessment of existing 20-year-old Rheem Criterion II Plus gas furnace and heating/cooling system located in basement serving medium-sized residential property of 1500-3000 square feet. Evaluated current equipment condition, ductwork configuration, and overall system performance to determine replacement specifications. Documented existing installation including furnace unit, metallic supply and return ductwork, PVC condensate drainage, gas piping, and ventilation components. Provided replacement estimate for complete HVAC system upgrade to address age-related efficiency decline and ensure continued reliable heating and cooling operation. Photographed existing equipment configuration and installation details for proposal documentation.

Completed comprehensive furnace maintenance and tune-up on a Lennox ML180UH090E48B unit installed in 2021. Performed standard heating system inspection including visual assessment of all components, electrical connections, and condensate drainage system. Documented equipment condition with photographs showing proper installation and operational status of the furnace, associated ductwork, and mechanical connections in the utility space.

Completed comprehensive MVP furnace maintenance service including inspection of blower assembly and control board components. Blower wheel showed normal dust accumulation on fins and housing; verified proper operation of centrifugal fan assembly and brass center fitting. Inspected electronic control board with heat sink, inductors, capacitors, and multi-colored wiring connections; confirmed all electrical connections secure and system operating within normal parameters.

Completed MVP cooling maintenance visit and addressed outdoor condenser unit settling issue. Performed standard system inspection of indoor air handler and outdoor condensing unit, verified refrigerant pressures using manifold gauges, and assessed structural stability concerns with outdoor unit placement on grade. Unit currently operational with settling condition documented for monitoring.