HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Completed routine AC tune-up on residential outdoor condenser unit. Inspected electrical connections, contactor, and wiring within compartment; verified proper grounding and terminal tightness. Cleared debris and leaves from around unit and concrete pad to ensure adequate airflow and proper operation.

Responded to water leak at toilet base. Upon inspection, removed toilet to assess wax ring and flange condition. Reset toilet with new wax ring and closet bolts, ensuring proper seal and secure mounting to prevent future leaks at base.

Responded to service call for 5-year-old gas furnace located in upstairs area experiencing operational issues. Upon arrival, performed diagnostic inspection of unit including visual assessment of internal components, blower motor assembly, gas valve connections, and control board wiring. Inspected and photographed air filter condition, which showed signs of restriction, and verified proper clearances for all mechanical and electrical components within the furnace cabinet. All accessible components including PVC venting, electrical connections, and safety controls were examined for proper operation and compliance with manufacturer specifications.

Completed MVP cooling maintenance visit on residential air conditioning system. Inspected outdoor condenser unit, verified proper operation of compressor and condenser fan motor, and checked electrical connections at disconnect box. Examined and photographed dual-element time-delay fuses (Ferraz Shawmut TR50R, 50A 250V AC) to document current protective device specifications. Noted significant debris accumulation including wet leaves on concrete pad surrounding unit and recommended clearing area to maintain proper airflow and drainage around equipment.

Completed full HVAC system installation including new 90% efficiency furnace and air conditioning unit. Installed outdoor condensing unit on exterior pad against brick wall with proper electrical disconnect box and conduit routing, verified 20-amp fuse protection, and ran refrigerant lines and drainage piping to interior equipment. All components tested and operational upon completion.

Replaced defective gas valve on HVAC system to restore proper gas pressure operation. Verified correct gas pressure reading of 0.16 inches water column using calibrated digital manometer after installation. System tested and confirmed operating within manufacturer specifications with proper airflow through heat exchanger louvers.

Completed scheduled MVP heating maintenance visit. Performed comprehensive system inspection and documented equipment condition, noting corrosion present on refrigerant line components that will require monitoring for potential future service needs. All system operations verified and unit confirmed functional at time of service.

Completed comprehensive assessment for furnace replacement on 26-year-old heating system that had reached end of serviceable life. Evaluated existing HVAC equipment including outdoor condensing unit positioned on concrete pad with proper landscaping clearances and basement furnace installation with associated ductwork and plenum assembly. Documented current system configuration, gas line routing, and existing duct connections to prepare detailed replacement quote for new high-efficiency heating equipment.

Completed scheduled BS-MVP cooling maintenance visit on HVAC system. Performed comprehensive inspection of control board assembly, documenting internal circuitry, wiring connections, and electronic components including PCB with integrated circuits, capacitors, and DIP switch configurations. Verified proper operation of all system controls and photographed control panel interior showing heat sink assembly, power supply unit, and sensor connections for maintenance records.

Completed installation of 80% efficiency furnace and air conditioning system. Replaced electrical disconnect fuses with Littelfuse Class RK5 time delay FLNR 20A 250VAC fuses to ensure proper overcurrent protection for the new HVAC equipment. System installed, tested, and verified operational.

Cut and removed existing 2" galvanized drain line in second floor bathroom wall. Adapted connection with new PVC fitting and 90-degree elbow, then reduced to 1-1/2" using bushing. Installed new Desanco fitting to accommodate existing 1-1/4" tubular trap from sink fixture. Installed new 1/2" ball valve for exterior spigot connection. All connections tested and verified leak-free upon completion.

Completed on-site evaluation of existing older furnace and air conditioning system for replacement estimate. Assessed current basement-mounted furnace unit and outdoor condenser positioned against brick exterior wall, documenting equipment condition, installation configuration, and necessary replacement specifications for both heating and cooling systems.

Responded to no-cool call on 11-year-old air conditioning system that had previously experienced coil freeze-up. Upon arrival, system had thawed but was not operating. Inspected outdoor unit service valves and refrigerant lines, which showed significant age-related deterioration and oxidation. System evaluated and customer advised of findings.

Completed multi-location plumbing fixture replacement and repair service. Installed customer-supplied kitchen faucet with new angle stop shut-off valves and supply lines beneath cabinet. Replaced basement lavatory faucet with customer-supplied unit, including installation of new shut-off valves and supply lines. Performed repairs on second-floor hallway bathroom, replacing the lavatory S-trap assembly and installing new flush valve seal in American Standard Champion toilet. All fixtures tested for proper operation and verified leak-free connections upon completion.

Responded to service call for plumbing modifications in kitchen area to accommodate installation of combo washer/dryer unit replacing existing dishwasher. Replaced existing hot water supply line and installed new cold water supply line to meet specifications for the new appliance. Ensured proper shutoff valves were installed for both supply lines, verified connections for leaks, and confirmed adequate water pressure and flow rates for optimal appliance operation.

Responded to a return visit for a previously repaired leaking pipe that had failed, likely due to freezing conditions. Opened interior wall and ceiling to access the affected copper plumbing, revealing deteriorated insulation and water damage in the wall cavity. Assessed the failed repair site, documented the condition of the copper piping showing varying degrees of oxidation, and prepared the area for proper re-repair of the leaking section.

Addressed electrical safety hazards in basement by properly securing open splices and installing code-compliant covers on junction boxes that were previously exposed. All electrical connections were verified for proper termination and boxes were secured to structural members per NEC requirements.

Responded to service call for 30+ year old natural gas furnace that was squealing and subsequently stopped operating. Accessed property using provided entry code as tenant was not home. Performed diagnostic inspection of furnace components and control systems. Examined electrical control board, wiring harness, and connections for signs of failure or deterioration. Inspected heat exchanger coils and associated mechanical components. Documented equipment condition through photographs showing control board with multiple wire connections, manufacturer specification labels with model and serial number information, and internal mechanical components including heat exchanger coils. Service waived as part of MVP membership enrollment.

Replaced failed sump pump system in 64-year-old residential basement with evidence of water intrusion and moisture damage to foundation walls. Installed new pump unit with proper drainage connections to existing white PVC discharge piping, verified electrical connections, and tested system operation to ensure adequate water removal capacity for basement protection.

Completed comprehensive MVP furnace maintenance inspection including combustion analysis using gas analyzer to verify proper natural gas operation and efficiency levels. Performed internal ductwork inspection with camera equipment, documenting moderate dust and debris accumulation throughout ventilation system that may impact airflow and indoor air quality if not addressed during future maintenance cycles.