HVAC, Plumber & Electrician Services in Fairlawn, OH

# Service Summary Responded to service call for leaking toilet in upstairs bathroom of 1973-built single-family residence. Inspected toilet assembly, identified source of leak, and performed necessary adjustments to restore proper function and eliminate water seepage. # Work Performed Upon arrival, conducted thorough visual inspection of the toilet assembly including tank, bowl, supply line, and floor-mounted connections. Examined the chrome braided supply line and shut-off valve for signs of moisture or deterioration. Assessed the tank-to-bowl connection, flush valve assembly, and fill valve operation to isolate the leak source. Identified worn flapper valve and deteriorated tank-to-bowl gasket as primary causes of water leakage. Shut off water supply at the wall-mounted valve and drained the tank completely. Removed tank lid and disconnected supply line from tank inlet. Unbolted tank from bowl to access and replace the compromised rubber gasket between components. Installed new

Performed annual maintenance on 11-year-old gas furnace. Inspected ignition system using hex key for adjustments and conducted electrical diagnostics with clamp meter showing 5.2 amp reading. System operating within normal parameters after service.

Responded to service call for clogged kitchen sink in 50-year-old home. Inspected drainage system in basement utility area, which revealed significant buildup in the main vertical waste stack. Successfully cleared obstruction using auger and restored proper drainage function throughout kitchen plumbing system.

Performed routine MVP Heating maintenance service, inspecting furnace components and electrical systems. Examined control board wiring connections and circuit integrity, confirming proper operation of all electronic components. Verified condensate drainage system functioning correctly with no blockages in PVC piping.

Performed routine cooling maintenance on Lennox outdoor AC unit. Inspected fan motor and blower assembly for proper operation, cleaned unit exterior, and verified system is functioning correctly. All components in working order with no issues detected.

Completed installation warranty service of a tanked water heater system, including copper pipe configuration with multiple joints and connections. Installed expansion tank with proper brass fittings and resolved previous installation balance issue as requested.

Diagnosed faulty thermostat connections by inspecting internal wiring and terminal connections. Identified and repaired corrosion issues on copper refrigerant lines at the evaporator coil, restoring proper system operation and cooling function.

Completed installation of new dedicated circuit for tankless hot water heater in basement and upgraded subpanel due to rust damage from exterior conduit water infiltration. Expanded electrical capacity with multiple new outlets including dedicated refrigerator circuit, installed nine recessed can lights with dual dimmer control, and added two LED fixtures in panel area. Installed whole home surge protector for improved electrical system protection.

Performed scheduled heating tune-up, inspecting gas valve assembly and electrical connections. Verified proper function of all components including wiring (red, white, green, yellow) and PVC ventilation system. System operating within normal parameters with no issues detected.

Performed scheduled MVP Heating maintenance service on Lennox furnace unit. Inspected and noted dust accumulation on air filter requiring replacement. Service was temporarily interrupted due to power outage but was successfully completed after power restoration.

Performed scheduled MVP heating maintenance on Lennox furnace system. Conducted comprehensive inspection of furnace unit, including examination of ductwork connections, ventilation system, and condensate drainage components. All systems functioning properly with no issues identified; unit appears well-maintained with secure connections throughout.

Responded to service call for gate valve inspection on exterior water faucet. Examined copper pipe system with visible red manual wheel valve and verified proper operation. No leaks or damage observed in the plumbing infrastructure; all connections and insulated sections remain in good working condition.

Completed routine MVP heating maintenance service. Inspected furnace unit and associated components including PVC exhaust, copper lines, and connections. Checked PROFLO shutoff valve for proper operation and verified no signs of leakage at threaded connections.

Responded to a service call for a laundry drain backup in the basement. Upon inspection, found standing water and moisture around the utility area with the blockage occurring in the main drain line connected to the laundry appliances. Successfully cleaned out the clogged drain line, restoring proper drainage functionality and preventing further water accumulation on the concrete floor.

Performed complimentary electrical inspection per customer request. Examined main service panel and identified intermittent breaker tripping issues. Inspected meter installation (reading: 15638) and evaluated distribution panel, finding properly routed wiring with no visible damage or code violations, though some breakers showed signs of wear that may contribute to reported tripping problems.

Performed scheduled MVP Heating Visit, conducting combustion analysis on natural gas system. Testing revealed CO levels at 11ppm, system efficiency at 80.3%, CO2 at 5.6%, and stack temperature at 308°F. Inspected blower assembly and heat exchanger components, noting normal dust accumulation but confirming all mechanical connections remain intact and functional.

Performed comprehensive AC tune-up on residential system of undetermined age. Inspected and cleaned outdoor condenser unit, removing accumulated debris from around base and fins. Examined motor/compressor assembly, noting normal operational wear and verified proper electrical connections to ensure optimal system performance.

Performed scheduled maintenance visit on furnace system. Conducted thorough inspection of electrical components and wiring connections within the unit, noting complex but functional wiring arrangement. Examined the Aprilaire Home Comfort Control unit mounted on the HVAC cabinet, documenting some signs of wear on the controller.

Responded to customer report of whistling noise from new furnace. Inspected unit's underside components including insulated hoses, ventilation openings, and connection lines. Identified and corrected improper routing of the black insulated hose that was causing air restriction and resulting noise.

Performed routine AC tune-up on 9-year-old Carrier system. Inspected and verified proper operation of the furnace and humidifier unit. System is functioning correctly with no issues detected; all components including PVC venting system and connections are in good working condition.