HVAC, Electrical & Plumbing Services in Hinckley, OH

Responded to service call for A/C unit short cycling every 4 minutes, 13 days post-installation. Upon inspection, identified issue with the control board and thermostat communication. Verified all wiring connections at the control module terminal block, checked thermostat status indicators showing proper power and communication signals, and confirmed the wireless setup module was functioning correctly. Addressed the short cycling issue by reconfiguring the control board settings and ensuring proper sensor operation. System tested and verified to be operating within normal parameters with appropriate run cycles restored.

Responded to emergency call for damaged underground utilities. During excavation work, both water and electrical lines running to the septic system were struck and compromised. Successfully repaired the damaged water line on-site. Electrical line remains damaged and requires follow-up service, as it may be heat tape which can be addressed by plumbing technician.

Responded to failed electrical inspection for generator installation. Corrected undersized seal tight connector at generator knockout to prevent water intrusion and installed proper size straps on seal tight conduit. Upgraded number 4 copper conductor to appropriately rated wire for 100-amp service. Documented existing electrical panel configuration showing main breaker section and distribution breakers with conduit routing. Awaiting delivery of 2-pole breaker to complete final connection.

Responded to no-cooling complaint on 3-year-old residential air conditioning system. Upon arrival, connected manifold gauges to measure refrigerant pressures and utilized digital instruments to diagnose the condenser unit. System was found to have improper refrigerant charge affecting cooling performance. Corrected refrigerant levels to manufacturer specifications, verified proper operation of condenser fan and compressor, and restored unit to normal cooling function.

Completed annual maintenance on one-year-old air conditioning system, performing standard inspection and servicing of outdoor condensing unit. Provided homeowner education on proper air filter replacement procedures and demonstrated condensate drain line maintenance using distilled white vinegar flush method to prevent future clogs and ensure optimal system performance.

Responded to service call for gas fireplace pilot light issues. Successfully relit pilot lights on two gas fireplaces in residence and verified proper ignition and flame operation on both units.

Successfully installed a 28kW Generac generator system with dual 200-amp automatic transfer switches to provide comprehensive backup power coverage for the residence. Installation included integration of cold weather protection kit with oil heater, dual load shed modules for prioritized power management, and two slow start kits to minimize startup surge demands on the system. Coordinated with gas line contractor for 30-foot natural gas supply line installation to fuel source. Mounted generator unit on exterior pad adjacent to stone facade wall, routing electrical conduit and gas piping along building exterior to minimize visual impact. Installed grey conduit vertically down stone wall corner with proper weatherproof fittings and junction boxes for code-compliant electrical connections. Configured both transfer switches to automatically detect utility power loss and seamlessly transfer critical circuits to generator power. Programmed load shed controllers to sequence non-essential loads

Completed installation of new Lennox 90% efficiency air conditioning system. Installed FLNR 45 amp fuses in outdoor disconnect for proper overcurrent protection of the condenser unit. System tested and operational upon completion.

Conducted on-site evaluation for whole-house standby generator installation. Assessed existing electrical service panel to determine compatibility and required modifications for generator integration. Panel inspection revealed 200-amp main service with adequate breaker capacity and proper circuit identification for essential loads. Documented current electrical configuration including HVAC systems, garage circuits, and critical household loads to establish transfer switch requirements. Photographed electrical panel layout and circuit distribution for accurate material estimation and permit preparation. Provided homeowner with recommendations for generator sizing based on existing electrical demand and discussed placement options for outdoor generator unit and automatic transfer switch installation.

Conducted comprehensive estimate for furnace and air conditioning system replacement at residential property. Customer reported unusually high utility bills and history of multiple refrigerant recharges by previous service provider. Evaluated existing Carrier furnace installation and associated air conditioning system, documenting current equipment configuration including PVC venting, electrical connections, and ductwork integration. Assessed system performance concerns and provided replacement options to address ongoing efficiency issues and repeated refrigerant loss indicating potential system failure.

Installed new gas line from main residence to pool and barn area to replace previously severed line. Trenched and ran new gas piping underground across property, connecting to existing gas supply at the home. Installed appropriate shutoff valves and flexible connectors at termination points, ensuring proper support and mounting of exposed pipe sections at structure connections.

Conducted on-site evaluation for whole home generator installation. Assessed basement utility area to determine electrical service capacity, available space for transfer switch installation, and proper routing for electrical conduit from main service panel. Evaluated attic space to identify optimal location for generator connection and reviewed existing electrical infrastructure. Documented current water heater, plumbing, and HVAC configurations to ensure proper clearances and code compliance for generator placement. Photographed electrical panel access points and structural considerations for load calculation and equipment sizing recommendations.

Completed preventive maintenance on a 2-year-old MVP air conditioning system. Inspected control board electronics, verified all wire connections and harnesses were secure, and examined the pleated air filter element which showed normal condition for the system's age.

Completed installation of 22kW Generac standby generator with 200-amp automatic transfer switch, oil warmer, and surge protection system. Ran 15 feet of gas line to unit and coordinated with gas utility for service connection. Wired transfer switch to main electrical panel, configured all circuits for automatic transfer during power outages, and verified proper operation of all safety systems and electrical connections per manufacturer specifications and local code requirements.

Responded to service call for 16-year-old Generac generator with reported low oil pressure issue. Upon arrival, performed comprehensive diagnostic evaluation of the unit including visual inspection, oil level verification, and pressure system assessment. Documented existing conditions with measurements and photographs of the generator installation at the exterior foundation location. Customer was advised that a detailed estimate for necessary repairs would be provided following the diagnostic evaluation.

Completed water heater replacement in residential utility room. Removed existing unit and installed new A.O. Smith ProLine tanked water heater with proper plumbing connections, expansion tank, drain pan, and temperature control assembly. All copper and PVC piping configured to code specifications with system tested and operational upon completion.

Responded to emergency call for outdoor GFCI outlet that experienced arcing and sparking incident. Upon arrival, found existing outlet installation with severely corroded metal electrical box, deteriorated weatherproof housing, and compromised wire connections due to prolonged moisture exposure. Removed damaged GFCI receptacle and corroded junction box from exterior wall. Installed new weather-resistant electrical box with proper sealing, replaced all compromised wiring, and installed new GFCI outlet with appropriate weatherproof-in-use cover rated for outdoor applications. Verified proper ground fault protection functionality through testing of trip mechanism. Additionally installed second outdoor receptacle at separate location on property as requested, ensuring compliance with exterior outlet spacing requirements and proper GFCI protection for outdoor circuits.

Conducted comprehensive HVAC estimate for complete system replacement including heat pump, furnace, and generator installation. Assessed existing mechanical room configuration with vertical ductwork and evaluated electrical panel capacity to determine requirements for new equipment integration and necessary electrical upgrades to support the proposed three-unit system installation.

Completed comprehensive air conditioning tune-up on residential HVAC system. Inspected evaporator coil and condenser components, noting minor surface oxidation at coil seam but no performance issues. Verified proper operation of furnace unit, condensate pump, and all associated drainage systems.

Performed comprehensive maintenance on Kohler residential backup generator system including inspection of all external components, conduit connections, and mounting hardware. Generator found in good operating condition with proper ventilation and secure installation on concrete pad. Investigated reported flickering lights throughout house and weak power issues in shed; inspected main electrical panel, branch circuits, and outdoor wiring runs. Examined exterior lighting circuits and conduit routing along foundation as requested. Verified all generator transfer switch connections and tested automatic startup functionality. Documented equipment condition with photographs showing generator placement, electrical connections, and associated exterior components including meter box and conduit pathways.