Blind & Sons: Trusted HVAC, Plumbing & Electrical Services in Massillon, OH

Completed installation of new air conditioning system including outdoor condensing unit and indoor evaporator coil. Outdoor unit was positioned on concrete pad against exterior brick wall with proper clearances maintained, electrical disconnect box mounted to structure, and line set connected between indoor and outdoor components. Indoor evaporator coil was installed in conjunction with existing Trane furnace in basement utility area, with refrigerant lines and condensate drainage properly routed through PVC piping. System was pressure tested for leaks, evacuated to manufacturer specifications, charged with appropriate refrigerant, and cycled through operational testing to verify proper cooling performance and airflow.

Installed electrical infrastructure for ceiling fan in residential room by tapping power from existing kitchen counter outlet on opposite side of wall. Ran switch leg from single gang box to attic, installed fan-rated junction box at ceiling location, and temporarily covered with blank plate pending homeowner's installation of fan fixture.

# Plumbing Service Completed Responded to a comprehensive plumbing service call addressing multiple system issues throughout the property. Primary focus involved snaking the downspout drain to clear blockages and restore proper drainage flow. Removed a malfunctioning garbage disposal unit from the kitchen sink assembly. Inspected the tankless water heater and identified significant mineral buildup requiring descaling service to restore efficiency and proper operation. Noted the absence of a drain line installation for the temperature and pressure relief valve, which presents a code compliance concern. Addressed basement plumbing needs by removing the existing toilet fixture and properly capping the drain line to prevent sewer gas infiltration and prepare the area for future use. Identified a leak in the cast iron stack line requiring repair to prevent water damage and maintain the integrity of the main drainage system. Documentation photos captured the utility area ceiling showin

Installed 25 feet of above-ground gas piping using pre-staged materials including gas line kit and pipe components. Routed new gas line through crawlspace area beneath floor joists alongside existing mechanical systems and stone foundation wall. Installation completed and confirmed operational per specifications.

Conducted comprehensive assessment of residential HVAC system experiencing major refrigerant leak resulting in complete loss of cooling capacity. Identified significant crack in furnace heat exchanger posing safety concern. Provided detailed replacement estimate for air conditioning system and recommended obtaining quote for complete system replacement versus partial repair approach. Documented existing Trane furnace installation, ductwork configuration, refrigerant lines, and condensate drainage system. Scheduled follow-up appointment with equipment buyback option to finalize replacement decision.

Installed dedicated electrical circuits for furnace and air conditioning system. Ran new wiring through unfinished framing to exterior disconnect box and HVAC equipment location. Verified proper circuit protection and confirmed all connections meet code requirements for HVAC electrical supply.

Responded to service call for 14-year-old air conditioning system with reduced cooling capacity. Performed diagnostic inspection using camera equipment to assess ductwork and system components for potential airflow restrictions, leaks, or structural issues affecting performance.

Completed routine MVP cooling maintenance on 5-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verifying proper operation of compressor, fan motor, and electrical connections. Inspected evaporator coil assembly and internal components, noting normal wear consistent with system age. Checked refrigerant lines for proper insulation and connections. Verified all electrical wiring and control circuits functioning within specifications. System operating efficiently with no immediate repairs required.

Installed four hardwired Ring security cameras on residential property with no existing fixtures or electrical boxes. Ran new wiring through attic space, sourcing power from garage door opener circuit. Mounted two floodlight cameras on siding blocks at rear and right-side roof peaks, installed standard camera on left roof peak with siding block, and mounted fourth standard camera in old work box on patio soffit above sliding glass door. All cameras hardwired and operational upon completion.

Responded to service call for attic ventilation fan cycling on and off intermittently. Inspected electric fan motor assembly and electrical connections, documenting condition of motor housing, wiring terminals, and fan blade assembly. Found older unit with accumulated dust and debris on motor components and blade surfaces, which can cause overheating and trigger thermal cutoff cycling.

Responded to emergency call for outdoor water spigot leaking into basement. Upon inspection, identified failed connection at exterior hose bib where copper pipe penetrated brick foundation, allowing water to flow through foundation opening and into interior space below. Accessed plumbing from basement side, replaced defective fittings and connections at spigot penetration point, and properly sealed foundation opening to prevent further water intrusion.

Responded to service call for toilet leaking from base onto floor below. Upon inspection, identified water seepage at toilet base causing damage to ceiling in room below, evidenced by cracking and separation at wall-ceiling junction. Documented existing conditions with photographs showing toilet installation and resulting water damage to lower level ceiling structure.

Installed eight customer-supplied LED recessed light fixtures in the living room and hallway ceiling. Verified proper electrical connections, tested all fixtures for functionality, and ensured even spacing and alignment throughout both areas.

Responded to report of water leak under kitchen sink with concern about loose spigot or malfunctioning garbage disposal. Upon inspection, identified active leak originating from garbage disposal unit and discharge connections. Assessed mounting hardware, drain connections, and disposal discharge pipe for proper seal and alignment. Placed absorbent materials beneath unit to contain water damage during diagnostic evaluation. Inspected water heater components in adjacent area as part of comprehensive plumbing system assessment. Verified all connections, tightened mounting assemblies, and tested for proper drainage flow to resolve leak issue.

Completed electrical panel replacement at residential property in preparation for fall season. Installed new circuit breaker panels to replace outdated equipment, ensuring proper load distribution and code compliance. Exterior meter base and junction box connections verified and secured with appropriate conduit routing along building siding. Interior basement installation included mounting dual panel configuration on concrete block wall with organized circuit breaker arrangement. All electrical connections tested and confirmed operational, improving overall system safety and reliability for the residence.

Responded to failed electrical inspection for grounding system deficiencies. Upon arrival, located two ground rods marked with identification flags in landscaped area. Inspection revealed ground rod clamp at first ground rod was not properly attached to the ground rod itself, compromising the grounding electrode system integrity. Additionally, found the grounding electrode conductor (GEC) wire exhibited significant damage at both ground rod connection points, with visible deterioration and compromised insulation. Documented all deficiencies with photographs showing the disconnected clamp, damaged conductor, and overall condition of the grounding system components. Work completed in one hour.

Responded to callback for leaking sink and garbage disposal connections following previous service visit. Upon inspection, identified active leaks at sink drain assembly and dishwasher discharge line connections. Removed and reinstalled garbage disposal with new mounting assembly and drain connections. Replaced deteriorated hose clamps and secured all drain hoses with stainless steel worm gear clamps. Reconnected dishwasher discharge line to disposal inlet with proper positioning to prevent backflow. Tested all connections by running water through sink basin and operating dishwasher through full drain cycle. Verified no leaks present at sink flange, disposal mounting ring, dishwasher connection, or waste line connections. All plumbing connections secure and functioning properly upon completion.

Responded to water leak complaint and performed diagnostic inspection of copper refrigerator supply line. Located active leak at connection point and assessed condition of existing saddle valve and shut-off valve assembly. Provided customer with repair options and quote for replacement saddle valve and shut-off valve installation to resolve leak and prevent future failures.

Completed routine maintenance visit on 6-year-old air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified blower wheel assembly operation, and assessed ductwork condition for potential cleaning needs. Unit found in operational condition with minor debris accumulation on top screen, which was noted for future service consideration.

Responded to water leak at toilet base with visible pooling after flushing. Upon inspection, confirmed failed wax ring seal causing water to seep from beneath toilet bowl onto carpeted bathroom floor. Removed toilet, scraped old wax ring and flange residue, inspected closet flange for damage and proper mounting. Installed new wax ring with plastic horn, reset toilet with new closet bolts, torqued to manufacturer specifications, and reconnected water supply line. Tested multiple flush cycles to verify proper seal and confirmed no leakage at base. Advised customer on signs of future seal failure and recommended monitoring for any moisture.