HVAC, Electrical & Plumbing Services in Strongsville, OH

Replaced a 120-volt, 2000-watt heating element on a Rheem low boy water heater. Rebuilt the cold water supply line to install a vacuum breaker, which was previously absent and causing the tank to siphon when water service was shut off. All necessary parts were procured and the installation was completed with proper copper piping, brass fittings, and flexible connectors to ensure code-compliant operation and prevent backflow issues.

Replaced failed 2002 A.O. Smith 40-gallon water heater with new Bradford White 40-gallon tall unit featuring 8-year manufacturer warranty. Installation included replacement of existing cold water shut-off valve, installation of bonding wire per code requirements, thermal expansion tank, and drain pan for leak protection. All copper connections completed with proper fittings, system tested and operational.

Completed comprehensive AC tune-up and preventative maintenance on a four-year-old cooling system for MVP member. Performed full system inspection including evaporator coil assessment, refrigerant line connections, and service valve examination. Observed dust and dirt accumulation on evaporator coil assembly and surrounding components, which is normal for system age and operation. Inspected air filtration system and noted heavily soiled pleated air filter requiring replacement. Verified refrigerant lines, brass fittings, and service valves showed no signs of leaks or degradation. System operational with no reported issues or symptoms prior to service call. All components functioning within normal parameters following maintenance procedures.

Replaced defective outdoor spigot at building exterior. Removed old fixture, installed new frost-proof hose bib, and tested for proper operation and leak-free connections.

Completed MVP cooling maintenance visit on outdoor air conditioning unit. Inspected and replaced failed TR30R 200/250A fuses in the electrical disconnect, which had prevented system operation. Verified proper connections of capacitor wiring and all electrical components within the unit compartment. System tested and confirmed operational upon completion.

Conducted on-site assessment and provided estimate for gas water heater replacement in residential property. Evaluated existing A.O. Smith ProMax gas water heater, approximately twenty years old, located in unfinished basement area with exposed framing. Documented current installation configuration including gas line connections, water supply piping with brass fittings and shutoff valves, vent pipe system, and drain connections. Assessed structural conditions of installation area, noting exposed wooden joists and adequate clearance for replacement unit. Photographed existing equipment and plumbing connections to provide accurate quote for new gas water heater installation, including removal and disposal of old unit and necessary code-compliant connections.

Completed scheduled preventative maintenance cooling visit on 2-year-old outdoor air conditioning unit. Performed comprehensive system inspection including electrical diagnostics using clamp meter to verify amperage draws and voltage readings across key components. Measured compressor amperage at 0.33A and monitored system performance parameters. Inspected capacitor condition, noting visible corrosion and rust on terminal connections with degraded wiring insulation present. Evaluated condenser coil fins and heat exchanger surfaces. Observed accumulated debris, dirt, and organic matter throughout unit housing with evidence of extended outdoor exposure causing weathering to internal components. Documented multicolored electrical wiring configuration and connection integrity across control board terminals. Unit operational at time of service completion with all findings photographed for maintenance records.

Responded to service call for filter replacement on HVAC system. Upon inspection, discovered significant dust and cobweb accumulation on electrical control board and system components, indicating extended period without maintenance. Replaced air filters, cleaned electrical connections and control board terminals to ensure proper system operation and prevent potential electrical issues from debris buildup. Verified all wire connections secure at terminal points and documented equipment serial number and manufacturer information for service records.

Responded to service call for 11-year-old Trane central air conditioning unit experiencing repeated breaker trips and system shutdowns. Upon arrival, performed diagnostic testing using thermal imaging to identify hot spot measuring 98.2°F at electrical connection point, indicating excessive resistance or loose connection. Utilized digital multimeter to verify electrical readings and confirm abnormal amperage draw of 12.93 amps at affected circuit. Identified failing contactor and compromised wiring as root cause of breaker trips. Repaired electrical connections, replaced defective contactor, and installed new programmable thermostat per customer request. Tested system operation through complete cooling cycle, verified proper amperage draw, and confirmed no further breaker trips. Unit restored to normal operating condition with stable electrical performance.

Completed installation of single-head Mitsubishi mini-split system in residential space. Mounted indoor air handler unit on interior wall above shelving area, installed outdoor condenser, ran refrigerant lines and electrical connections, and performed system startup and testing. Verified proper operation with temperature readings confirming unit cooling to 68.7°F at time of completion.

Replaced both exterior hose spigots with frost-free units to bring the installation up to current plumbing code. Removed existing gate valves and installed new quarter-turn ball valves for improved shutoff reliability. Ran new copper supply lines from the ball valves to the frost-free spigots, utilizing proper soldering techniques at all joints and connections. Secured both spigot assemblies to the exterior wall with appropriate mounting hardware and sealed all penetrations through the siding to prevent water intrusion and air leakage.

Performed annual maintenance and flush service on Navien tankless water heater. Descaled heat exchanger, cleaned inlet filter screen, inspected all plumbing connections and electrical components, and verified proper operation. Unit tested and confirmed functioning within normal parameters upon completion.

Removed existing two-handle shower valve and tub spout assembly from tiled shower enclosure. Accessed plumbing from rear access panel and cut copper supply lines, installing new ball valves to provide future isolation capability for the shower system. Installed new Moen single-handle Posi-Temp pressure-balancing shower valve, connecting to existing riser within wall cavity. Mounted chrome trim kit and single-handle control on valve body. Installed new chrome tub spout on copper stub-out. Fitted white remodel escutcheon plate over wall penetrations to conceal openings left by previous two-handle configuration. Applied silicone bead around perimeter of remodel plate to secure fixture and create water-resistant seal preventing moisture intrusion behind shower wall. Tested system for proper operation, temperature control, and verified no leaks at connections. Installation restored full shower and tub functionality with updated single-handle control system.

Completed estimate for full air conditioning system replacement due to non-operational unit with evaporator coil icing issues. Assessed existing outdoor condenser unit and indoor air handler, documented current equipment condition, and provided quote for complete system replacement including new outdoor condensing unit and indoor air handler with associated ductwork modifications.

Responded to service call for 10-year-old whole-house AC system not cooling properly. Upon inspection, discovered evaporator coil completely frozen with extensive ice buildup throughout the unit, indicating restricted airflow or low refrigerant charge. Documented frost accumulation on coil assembly and surrounding components. Assessed outdoor condensing unit and associated refrigerant lines at exterior of property. System required defrost cycle completion before further diagnostic testing could be performed to determine root cause of freezing condition, which may include dirty air filter, blocked return air, low refrigerant levels, or failed blower motor.

# HVAC Service Report Responded to no-cooling complaint on 5-year-old residential AC system affecting entire home. Upon inspection, found exterior condensing unit filter and condenser coil heavily contaminated with dirt, dust, and debris buildup, significantly restricting airflow and reducing system efficiency. Removed and cleaned exterior filter, which showed substantial dust accumulation and discoloration from extended use without maintenance. Thoroughly cleaned condenser coil fins, removing thick layers of accumulated particulate matter that had embedded between the horizontal fins, particularly concentrated on the left and center portions of the coil. Heavy contamination was preventing proper heat exchange and causing system to fail cooling. After cleaning both components, verified adequate airflow through condenser unit and confirmed system restored to normal cooling operation. Documented condition with photos showing before-cleaning state of filter and coil. Advised homeowner on

Completed comprehensive tune-up on 10-year-old air conditioning system. Performed full system inspection including evaporator coil examination, blower wheel assessment, and refrigerant line connections verification. Documented system components with photographic evidence showing clean evaporator coil with serpentine fins, properly functioning centrifugal blower assembly, and filter drier installation with secure copper line connections, confirming all components operating within normal parameters.

Responded to service call for water heater leaking from bottom in utility closet. Upon arrival, inspected A.O. Smith tanked water heater and confirmed active leak originating from base of unit. Evaluated tank condition and determined internal tank failure causing water discharge onto concrete floor. Documented existing installation including copper supply lines, expansion tank, and flue venting system. Due to compromised tank integrity and safety concerns, recommended immediate replacement of failed water heater unit. Coordinated with property manager for approval and scheduling of replacement installation.

Responded to drain pipe maintenance call for shower in 40-year-old home where previous repair from two years ago had failed. Upon inspection, found bathtub drain assembly showing significant buildup and discoloration around lower drain fitting, with debris accumulation affecting proper drainage. Accessed crawlspace area to inspect drain line routing and connections through floor structure. Cleared obstruction from shower drain, removed accumulated debris and buildup from drain fittings, and verified proper water flow through drain system. Tested drain operation to ensure complete resolution of drainage issue.

Completed scheduled cooling maintenance visit on 13-year-old HVAC system. Inspected electrical disconnect panel and identified signs of age-related wear, heat discoloration, and charring near wire entry points at the base of the enclosure. Examined internal wiring connections, terminal screws, and bus bar assembly for proper contact and potential safety concerns. Performed necessary electrical connection assessment and documented condition of disconnect mechanism and associated wiring for maintenance records.