Air Conditioning, Heating, Electrical & Plumbing Services in Tallmadge, OH

Completed maintenance tune-up on two 15-year-old outdoor AC units. Cleared significant accumulation of mulch, leaves, and organic debris from around and beneath both units to restore proper airflow and prevent potential drainage issues. Inspected refrigerant lines, verified proper connections, and ensured both systems were operating within normal parameters.

Completed scheduled maintenance visit for MVP customer at confirmed 8:30 AM appointment. Performed standard cooling system inspection on outdoor condenser unit, documenting equipment condition with photographs showing unit operating on concrete pad with proper clearances maintained.

Responded to service call for flickering garage light caused by loose socket connection. Inspected and tightened the light fixture socket to eliminate flickering issue and restore proper electrical contact. Also discussed heat tape installation options for gutter snow melting with the customer, explaining the system requirements and providing guidance for future consideration.

Completed MVP cooling maintenance visit on HVAC system. Performed comprehensive inspection of equipment components, including evaporator coil assembly and control board systems. Documentation revealed significant rust and corrosion on copper tube coil assembly and mounting brackets, indicating extended exposure to moisture. Inspected electrical control panel, circuit board, relays, contactors, and wiring connections. All system components photographed for maintenance records. Unit operational at time of service completion.

Completed first MVP maintenance visit on Lennox heating and cooling system following initial installation. Inspected furnace, air handler, and associated components including PVC venting, ductwork connections, and Aprilaire humidifier unit. Documented heavily soiled air filter requiring replacement due to significant dust and debris accumulation across pleated surface. Verified system operation, checked all connections, and photographed equipment condition for service records.

Responded to service call regarding chirping smoke detector near bedroom door. Upon arrival, inspected ceiling-mounted smoke alarm unit and confirmed customer had attempted battery replacement but was unable to properly install new batteries. Assessed smoke detector installation and battery compartment accessibility. Opened detector housing, removed old batteries, and installed fresh batteries with correct polarity. Verified secure battery connection and proper seating within compartment. Tested smoke detector functionality to confirm chirping issue was resolved and unit was operating correctly. Reinstalled detector cover and ensured proper mounting to textured ceiling surface.

Responded to service call for leaking shower shut-off valve at wall connection. Upon inspection, identified active leak at the wall-mounted shower valve assembly. Repaired the faulty shut-off mechanism to restore proper function and eliminate water seepage at the fixture mounting point.

Completed comprehensive AC tune-up on 6-year-old outdoor condensing unit. Performed standard maintenance protocol including inspection of condenser coils, fan assembly, and electrical components; unit operational with normal airflow and no issues identified. Cleaned debris from base area and verified proper operation of all systems.

Performed annual maintenance flush on tankless water heater system in residential basement. Isolated unit using shutoff valves, circulated descaling solution through heat exchanger to remove mineral buildup, flushed system thoroughly, and restored operation. Unit tested successfully with proper flow rates and temperature output; system operating within normal parameters with no leaks detected at connections.

Conducted comprehensive assessment of existing residential HVAC system for replacement estimate. Evaluated indoor Amana furnace unit and associated ductwork in basement utility area, documenting equipment age, condition, and configuration. Inspected outdoor air conditioning condenser unit, electrical disconnect, and installation pad. Photographed both indoor and outdoor components to provide detailed documentation for replacement system specifications and scope of work.

Responded to service call for Generac Evolution 2.0 generator that would not shut off over the weekend and had to be manually unplugged by homeowner. Upon arrival, inspected generator control panel displaying firmware/hardware version V1.6 and verified all control buttons (AUTO, MANUAL, OFF) for proper operation. Examined automatic transfer switch assembly, including Generac control module with status indicators, circuit breakers, contactors, and associated wiring connections. Tested system functionality, verified proper shutdown sequence, and confirmed generator now responds correctly to OFF command and operates normally through all control modes.

Performed routine maintenance inspection on 16-year-old residential air conditioning system for MVP customer. Appointment was rescheduled to accommodate customer availability, and service was completed as requested with diagnostic equipment and testing tools deployed at outdoor condenser unit.

Conducted comprehensive assessment of existing HVAC system in basement mechanical room for complete furnace and air conditioning replacement estimate. Evaluated current Luxaire furnace unit and associated air handler, documented existing ductwork configuration including flexible and rigid metal ducts, and assessed utility room infrastructure including water heater clearances and available space for new equipment installation. Photographed all existing equipment, connections, and mechanical room layout to provide accurate replacement specifications for bundled furnace and AC system upgrade per promotional offer inquiry.

Responded to water leak under kitchen sink in 22-year-old residential property. Upon inspection, discovered active leak in PVC drainage assembly beneath sink, with visible water damage and dark staining present on cabinet floor in multiple areas. Plumbing configuration included white PVC P-trap system, garbage disposal unit with connecting drain lines, dishwasher drain connection, and standard hot/cold water supply lines with braided flex hoses. Customer indicated that kitchen pipes had been previously replaced approximately 14 months prior and inquired about potential warranty coverage or service discount. Documented existing conditions with photographs showing full plumbing assembly, drainage connections, water supply lines, and extent of water damage to cabinet interior. Service appointment was rescheduled to allow for warranty verification and proper repair planning.

Completed comprehensive estimate for furnace and air conditioning system replacement. Evaluated existing Lennox outdoor condensing unit and indoor gas furnace installation in garage, documented current equipment condition and configuration through detailed site photography. Customer interested in BOGO half-off promotion; left message to confirm discount eligibility and finalize replacement proposal.

Replaced 40-gallon tall residential water heater in basement utility area. Installed new unit with complete water heater kit including copper supply lines, brass fittings, and proper venting connections. All plumbing connections secured and tested for leaks, system restored to full operation with 6-year warranty coverage.

Responded to service call for leaking water heater. Upon arrival, performed diagnostic inspection of residential tanked water heater located in basement utility area. Confirmed active leak originating from bottom of tank, indicating internal tank failure. Water heater identified as Rheem Professional Series unit of unknown age with significant corrosion and deterioration at base. Documented equipment condition with photographs showing compromised tank integrity, existing plumbing connections including copper supply lines, temperature and pressure relief valve, expansion tank, and proximity to HVAC furnace system. Advised customer that bottom tank leaks are non-repairable and require complete water heater replacement due to structural failure of inner tank lining. Provided replacement options and recommendations for new installation.

Replaced an 80-gallon AO Smith electric water heater experiencing severe corrosion with a new Navien NPE-240A2 tankless water heater. Connected gas supply to existing 1-inch main trunk line and mounted unit in utility area. Core drilled through brick exterior wall at front of house for proper venting and exhaust installation. Installed condensate pump with discharge line routed to furnace drain location. Coordinated electrical conversion from 240V to 110V service. All copper supply lines connected, system tested and operational.

Performed electrical estimate for generator installation in unfinished basement utility space. Assessed existing electrical infrastructure including 200-amp Eaton BMH125K circuit breaker panel with proper UL certification and busbar configuration. Documented site conditions including exposed ceiling joists, existing plumbing and HVAC systems, concrete block walls, and available floor space for equipment placement. Evaluated electrical service capacity and panel accessibility for generator transfer switch integration. Photographed electrical panel specifications, existing conduit routing, and workspace layout to prepare comprehensive installation estimate.

Installed six ceiling fans throughout a residential property, including one in the first-floor living room, four in second-floor bedrooms, and one in the second-floor living room. Five of the six locations had no existing wiring, switch boxes, or mounting hardware, requiring complete electrical rough-in from scratch. Ran new electrical circuits from the panel to each fan location, installed junction boxes rated for fan support, and mounted appropriate wall switch boxes where none existed. The second-floor living room location had an existing switch box, simplifying installation at that point. Fished wiring through walls and attic spaces in the 2-3 year old home, ensuring minimal wall damage and proper code compliance. Installed fan-rated electrical boxes securely fastened to ceiling joists at all six locations. Completed all wiring connections, mounted ceiling fan brackets, assembled and hung all fan units, and installed corresponding wall controls. Verified proper operation of all fan