Air Conditioning, Heating, Electrical & Plumbing Services in Tallmadge, OH

Replaced faulty sump pump check valve and rebuilt the discharge line section exiting the residence. Secured piping to wall with appropriate strapping to ensure proper drainage flow and prevent future movement. Work completed over two hours following parts delivery to shop.

Performed descaling maintenance on a 17-year-old Rinnai tankless water heater unit. Flushed the heat exchanger with descaling solution to remove mineral buildup, verified proper operation of all components, and confirmed unit was functioning within manufacturer specifications upon completion.

Responded to no heat call on one-year-old furnace system. Upon arrival, accessed unit and performed diagnostic inspection of internal components including blower assembly, control board wiring, and ignition system. Verified all electrical connections were secure and inspected copper refrigerant lines and condensate drainage system. System restored to proper heating operation and tested for normal cycling.

Responded to sump pump overflow and drainage blockage in 20-year-old residential property. Upon inspection, identified compromised sump pump system in basement with discharge pipe configuration issues and evidence of water intrusion around basin perimeter. Assessed exterior drainage concerns including significant standing water accumulation on patio area, indicating potential backflow or inadequate discharge routing. Cleared blockage from pump system, verified proper operation of discharge lines, and restored functionality to prevent further basement flooding and exterior water pooling.

Completed annual air conditioning maintenance and tune-up on a 4-year-old residential cooling system. Performed comprehensive inspection of all major components including blower motor assembly, refrigerant lines, and electrical connections. Examined control board circuitry and verified proper operation of outdoor discharge air sensor and integrated circuit components. Checked wire terminations and connections throughout the system, ensuring all wire nuts and harness connections were secure. Inspected copper refrigerant lines for proper insulation and connections to blower motor housing. Verified all safety labels and operational information were visible and legible. System tested and operating within normal parameters upon completion of maintenance service.

Responded to service call for non-operational sump pump with rising water levels in basement utility area. Upon arrival, inspected sump pump basin and found pump had failed, preventing proper drainage and allowing water accumulation in pit. Removed defective pump unit from basin and tested float switch mechanism, confirming mechanical failure. Installed replacement sump pump with appropriate horsepower rating for residential application. Connected discharge piping to existing white PVC vertical pipe running up wall. Verified all electrical connections were secure and properly grounded. Tested pump operation by filling basin and confirming automatic float activation and proper water discharge through existing drainage system. Pump cycled correctly and reduced water level as designed. Advised property occupant of extensive moisture damage and water staining visible on basement walls and floor, indicating history of water infiltration issues that may require additional waterproofing measu

Responded to gas service call for reported gas leak with gas supply shut off at roadside meter. Performed systematic leak detection inspection throughout property, checking all natural gas appliances, connections, and supply lines. Inspected interior gas piping at electrical panel area and exterior meter installation. Documented findings with photos and contacted property owner with results and recommendations for restoring gas service.

Completed MVP cooling maintenance on residential HVAC system. Performed comprehensive inspection of outdoor condensing unit, verified all refrigerant lines and electrical connections were secure and properly functioning, and inspected indoor air handler with pleated filter in place. All system components found to be in operational condition with no repairs required at this time.

Completed routine MVP heating maintenance visit on residential HVAC system. Performed comprehensive inspection of furnace mechanical components, condensate drainage system with PVC piping, and ductwork connections. Verified proper operation of Aprilaire whole-house humidifier unit including control settings, water supply connections, and electrical components to ensure optimal system performance for the heating season.

Performed inspection of outdoor condensing unit and identified significant dirt buildup on condenser coil affecting system efficiency. Recommended annual chemical cleaning of outdoor condenser to maintain peak performance and optimal heat transfer. Additionally recommended installation of surge protector on outdoor condenser to provide protection against electrical surges and voltage spikes that could damage compressor and electrical components.

Completed preventive maintenance cooling visit on outdoor HVAC unit. Inspected electrical components, capacitor, and wiring connections; all found to be in good working condition with proper organization and no signs of deterioration. Unit exterior showed normal weathering with system operating within manufacturer specifications.

Completed installation of new internal check valve and flow sensor on existing Navien 240a tankless water heater. Accessed internal components of the unit, integrated the flow sensor into the water supply line, and installed the check valve to prevent backflow and ensure proper system operation. All connections were secured with appropriate fittings, electrical connections were made to the control board, and the unit was tested to verify proper flow detection and valve function. The water heater was reassembled and returned to full operational status.

Responded to slow bathroom drain complaint at 62-year-old residential property. Accessed plumbing assembly beneath sink and inspected P-trap, drainage connections, and supply lines. Disassembled chrome P-trap to remove accumulated debris and buildup causing drainage restriction. Cleared blockage, reassembled all compression fittings, and tested drainage flow to confirm proper operation. All components reinstalled and system restored to normal function.

Inspected outdoor condenser unit and found coil heavily packed with dirt and debris, significantly restricting airflow and reducing system efficiency and cooling capacity. Recommended chemical coil wash to restore proper airflow and performance. Scheduled service for dry weather conditions to ensure optimal cleaning results.

Completed MVP cooling maintenance visit on residential Lennox air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified proper refrigerant line connections and electrical disconnect functionality. Inspected indoor evaporator coil and documented moderate dust accumulation on aluminum fins, which may impact airflow efficiency if not addressed during future maintenance intervals. All system components operational and accessible for ongoing service requirements.

Completed MVP cooling maintenance visit and inspection of residential HVAC system. Upon inspection, discovered significant frost and ice accumulation on the evaporator coil assembly, indicating a system malfunction. The heavy crystalline buildup was covering the serpentine aluminum tubes and backing plate, with frost also present on the blower wheel component. This condition typically results from restricted airflow, low refrigerant charge, or other system inefficiencies that prevent proper heat exchange. Documented the furnace and air handler installation in the utility area, noting the configuration of ductwork, PVC condensate drainage, gas line connections, and associated components including the humidifier unit. Photographed the frosted evaporator coil assembly showing the extent of ice buildup on the heat exchanger tubes, refrigerant lines with brass fittings, and areas of rust or corrosion on metal components. The system requires immediate attention to address the icing conditio

Upon arrival, conducted a comprehensive basement plumbing inspection and identified multiple concerns requiring immediate attention. Discovered eight corroded SharkBite fittings throughout the basement plumbing system, presenting potential failure points in the water distribution infrastructure. Evaluated the whole home shutoff valve and determined replacement was necessary to ensure proper water supply control and system integrity. Assessed shutoff valves serving both front and outdoor spigots and recommended complete replacement including installation of new sillcocks to provide reliable exterior water access and prevent future leaks. Documented existing copper and PVC piping configuration in the unfinished basement area, noting the various supply and drainage lines mounted to ceiling joists. Provided the homeowner with comprehensive repair options addressing all identified issues, including individual component repairs and a complete system upgrade package. Explained that replacem

Completed recurring maintenance visit on two 26-year-old HVAC systems. Performed system diagnostics including amperage readings which measured 90.1A on the compressor unit. Identified heavily clogged evaporator coil with significant dust and debris accumulation obstructing airflow through the fins. Documented equipment condition through photos for service records.

Completed annual air conditioning tune-up and system inspection on Airtemp unit. Performed comprehensive evaluation of indoor air handler components including blower motor, electrical connections, and control board, confirming all wiring harnesses and mechanical components operating within normal parameters. Inspected outdoor condenser unit, verified proper operation of compressor and fan motor, and checked refrigerant levels and system pressures. All components found to be functioning properly with no immediate service needs identified.

Completed MVP cooling maintenance visit on residential HVAC system. Performed comprehensive inspection of outdoor heat pump unit and indoor Lennox furnace, examining electrical connections, capacitor, contactor, and refrigerant line connections at both locations. Documented equipment condition through photographic records showing all major components operating within normal parameters.