Heating, AC, Plumbing & Electrical Services in Twinsburg, OH

Repulled wiring for under cabinet lighting circuit on kitchen's far left section. Removed existing puck lights and installed three new 24-volt LED puck lights with corresponding 24-volt driver to ensure proper voltage compatibility and operation. Replaced exterior deck outlet with new GFCI receptacle and weatherproof cover. Attempted to source power from bathroom circuit to provide independent GFCI protection for deck outlet; however, existing bathroom GFCI already protects two additional bathrooms, making independent operation unfeasible without compromising current protection scheme. Completed installation with existing circuit configuration to maintain proper GFCI protection throughout affected areas.

# HVAC Duct Cleaning and Humidifier Maintenance Performed comprehensive duct cleaning service for residential HVAC system with approximately 8 supply and return vents. Upon initial inspection, discovered extensive biological growth, including mold and mildew contamination throughout the main trunk line and branch ductwork. Noted significant accumulation of dust, debris, and fibrous insulation material within the ventilation system, indicating prolonged lack of maintenance. Utilized negative air pressure equipment and rotary brush system to thoroughly clean all accessible ductwork from supply plenum through branch runs to individual vent terminals. Removed heavy deposits of mold, dust, lint, and organic matter from interior duct surfaces. Applied particular attention to corner joints and connection points where contamination was most concentrated. Addressed water damage indicators and surface corrosion observed on interior metal surfaces. Cleaned ceiling, wall, and floor surfaces of

Returned to property to level outdoor air conditioning unit that had settled unevenly on its concrete pad. Applied gravel base material from warehouse inventory beneath and around the equipment pad to ensure proper drainage and stability. Work was performed during appropriate weather conditions with temperatures consistently at or above 65 degrees as required for safe installation. Completed exterior work without requiring interior access to the residence. Both HVAC units now sit level on stabilized concrete pads with adequate gravel bedding for long-term support and water management.

Completed installation of new Lennox 90% AFUE gas furnace and air conditioning system at residential property. Installed outdoor condensing unit on concrete pad against exterior wall with proper clearances and mounted electrical disconnect box with 35-amp Littelfuse FLNR fuses for equipment protection. Ran refrigerant lines, established electrical connections, and verified all components operational per manufacturer specifications.

Completed routine AC maintenance on residential Lennox condenser unit. Performed standard inspection of outdoor unit including visual assessment of cabinet condition, clearances, and surrounding area. Inspected electrical components and replaced TR25CR time-delay fuse (250VAC, RK5 rated) in disconnect box. Unit operational with proper clearances maintained from structure and adequate airflow around condenser. All electrical connections secure and system functioning within normal parameters.

Completed scheduled heating maintenance visit on a 2-year-old Lennox gas furnace system. Performed comprehensive inspection of unit including verification of proper venting through metallic exhaust system, confirmed all components operational with access panel properly secured, and documented equipment condition showing no visible defects or concerns.

Completed startup and commissioning of newly installed air conditioning system. Verified proper installation of exterior line set connections, diverter box mounting, and electrical conduit routing along building exterior. System tested and confirmed operational, ready for customer use.

Conducted comprehensive on-site evaluation of existing Bradford White residential water heater installation to provide replacement estimate. Assessed current unit configuration including copper supply line connections, brass fittings, pressure relief valve piping, and exhaust flue venting system. Inspected all shut-off valves, pressure regulators, and control devices for proper operation and code compliance. Documented existing plumbing infrastructure, ductwork connections, and mechanical space constraints. Photographed installation details including hot and cold water line routing, valve assemblies, and ventilation components to prepare accurate replacement proposal.

Completed on-site evaluation for complete HVAC system replacement at residential property. Assessed existing basement-installed furnace unit with associated gas lines, plumbing connections, and electrical components, as well as exterior air conditioning condenser unit with protective cage mounted on concrete pad. Provided comprehensive estimate for furnace and air conditioning system replacement based on current equipment condition and customer requirements.

Responded to service call for malfunctioning outdoor water spigot with active water leak. Upon arrival, found existing hose bib continuously flowing water due to failed internal valve mechanism. Shut off water supply at main line to prevent further water waste and potential property damage. Removed deteriorated copper spigot assembly from exterior wall mounting point. Installed new frost-free hose bib with proper sealing and secure attachment to existing copper supply line. Restored water main, tested new fixture for proper operation and verified no leaks at connection points or valve seat.

Completed estimate for furnace and air conditioning system replacement in residential basement mechanical room. Evaluated existing HVAC equipment including water heater, ductwork, and associated piping infrastructure. Quoted BOGO 120 BB system package rated at 540 capacity. Identified and documented high and low pressure switch failures with visible cracks requiring replacement, estimated at 2000+ for repair components. Assessed current installation including gas line connections, copper piping, flexible ductwork, and mounting configurations. Provided comprehensive replacement proposal for complete heating and cooling system upgrade.

Completed full HVAC system installation including 90% AFUE gas furnace and air conditioning condenser unit. Installed furnace in basement mechanical room with proper venting using white PVC piping, connected to existing ductwork infrastructure via galvanized metal plenum and flexible duct connectors. Routed copper refrigerant lines from basement to exterior condenser location, installed attic ductwork components with insulated plenum box to ensure proper airflow distribution throughout residence. Verified all electrical connections, tested system operation for heating and cooling cycles, confirmed proper condensate drainage, and ensured all safety controls functioning within manufacturer specifications.

Responded to service call for Daikin mini split system experiencing short cycling issues with outdoor unit turning on and off every few minutes. Inspected condenser unit, mounting pad, electrical connections, and drain line configuration. Unit found properly secured on pad with adequate clearance; documented current installation condition with photos for service records.

# Tankless Water Heater Maintenance Service Performed preventative maintenance flush and descaling service on wall-mounted tankless water heater unit. Isolated unit from water supply, connected flushing equipment, and circulated descaling solution through the heat exchanger for recommended duration to remove mineral buildup and calcium deposits. Removed and cleaned inlet filter screen, which showed typical sediment accumulation from normal operation. Flushed system thoroughly with clean water to remove all descaling solution and debris. Reinstalled cleaned filter, restored water supply, verified proper operation of unit including flow rates and temperature output. Unit returned to service with no performance issues noted. System operating efficiently with clear water flow and proper heating function confirmed.

Performed routine maintenance on a 2-year-old air conditioning system under manufacturer's MVP program. Inspected and cleaned outdoor condenser coil which showed moderate dirt and debris accumulation on aluminum fins. Cleared condensate drain line of mineral deposits and verified proper drainage flow to prevent future blockages.

Performed comprehensive preventive maintenance on two-year-old HVAC cooling system for MVP member. Conducted complete system tune-up including inspection of control board, capacitor, and electrical connections. Verified proper operation of all electronic components, circuit board functionality, and wiring harness integrity. Inspected and tested run capacitor, confirmed secure mounting and proper electrical connections. Checked all wire terminations, terminal blocks, and connector housings for signs of wear or loose connections. Documented system condition with photographs of control panel and electrical components. All components found in good working condition with no immediate repairs required. System operating within manufacturer specifications.

Responded to service call for 15-year-old air conditioning system experiencing intermittent cooling cycles. Upon inspection, diagnosed faulty compressor contactor and deteriorated refrigerant line insulation in attic space. Replaced defective contactor with OEM-spec component, securing all electrical connections. Re-insulated exposed refrigerant lines with proper R-value wrap to prevent condensation and maintain system efficiency. System tested through multiple cooling cycles, verified consistent operation with no interruptions, and confirmed proper amperage draw at compressor.

Responded to service call for clogged bathroom sink with water backing up. Upon inspection, accessed the drain assembly beneath the sink and found accumulated debris and buildup in the P-trap causing the blockage. Disassembled the drain components, cleared the obstruction, and cleaned the trap thoroughly. Reassembled all plumbing connections, tested drainage flow, and verified proper operation with no leaks detected.

# HVAC Install - Complete System Completed installation of 80-foot AC lineset routed through attic space to connect outdoor condensing unit to indoor air handler. Installed Lennox furnace system in utility closet with proper ductwork connections, including flexible metal ducting and silver-colored supply/return plenums with elbow joints for optimal airflow distribution. System positioned adjacent to existing Rheem water heater with adequate clearance for service access and ventilation requirements. All refrigerant lines properly insulated and secured throughout attic run to prevent energy loss and ensure efficient operation. Electrical connections completed per manufacturer specifications and local code requirements. Verified all mechanical connections, tested system operation, and confirmed proper airflow through ductwork. Installation includes all necessary labels, warning stickers, and specification documentation affixed to equipment. System commissioned and ready for operation.

Disconnected and relocated outdoor condenser coil at homeowner's request, reinstalling unit in the same position. Verified system pressures and subcooling values using manifold gauges to ensure proper refrigerant charge and system operation after reconnection.