Your Trusted HVAC, Plumbing & Electrical Experts in Wadsworth, OH

Repaired leaking CPVC water line in basement ceiling at a 3/4" x 3/4" x 1/2" tee fitting with a 3/4" street 90 connection. Reconfigured the piping by installing a 90-degree elbow on the straight run, adding a tee fitting in the middle section, coupling back to the existing 3/4" pipe, and installing a street 90 to complete the final connection. All fittings were properly secured and tested for leaks to ensure system integrity.

Completed full HVAC system installation including 80% efficiency furnace, air conditioning unit, and complete ductwork system in attic space over multiple days. Installed new electrical disconnect with 30-amp Littelfuse fuses and proper conduit routing at outdoor condensing unit location, ensuring all components meet code requirements and manufacturer specifications for safe system operation.

Completed preventive maintenance cooling visit on 6-year-old air conditioning system for first-time service customer. Performed comprehensive inspection of air handler unit located in basement mechanical room, verified proper operation of all components including blower assembly and electrical connections. Inspected and documented Aprilaire humidifier installation, ductwork connections, and condensate drainage system to ensure all equipment functioning within manufacturer specifications.

Responded to water leak originating from basement floor tiles in a 23-year-old residential property. Upon arrival, accessed ceiling infrastructure to inspect exposed plumbing system, including PVC drain lines and vent pipes mounted to wooden support beams. Identified leak source in overhead plumbing connections, documented existing pipe configuration with vertical drain line and horizontal waste lines. Repaired faulty connection point, tested system for proper drainage and verified no additional moisture intrusion. Trip charge waived due to membership status.

Responded to a toilet leak at the base with visible discoloration on a 21-year-old condo unit. Upon inspection, identified failed wax ring seal as the source of water seepage around the toilet base. Removed and reset toilet with new wax ring and hardware to restore proper seal and prevent further water damage to flooring.

Completed scheduled preventative maintenance cooling visit on 5-year-old air conditioning system. Performed comprehensive system inspection including cleaning of heavily soiled blower wheel assembly which showed significant dust and debris accumulation on fan blades and internal components. Inspected evaporator coil and heat exchanger fins within air handler, verified proper airflow through ductwork, and documented system condition with photos. All components operational upon completion of maintenance service.

Performed comprehensive assessment of 60-year-old residential boiler system for replacement estimate. Unit shows significant age-related wear with deteriorated components, oxidized copper piping, and outdated safety mechanisms. Documented existing equipment configuration including expansion tank, pressure relief systems, and distribution piping to provide accurate replacement specifications and scope of work required for new installation.

Completed routine air conditioning maintenance on 6-year-old system located in basement utility area. Performed standard tune-up procedures including inspection of HVAC unit, ductwork, and associated components. Evaluated ductwork condition and discussed cleaning recommendations with customer. Customer declined membership program enrollment at this time.

Responded to report of natural gas odor detected near 3-year-old generator unit. Upon inspection, identified corroded gas line connections at the flex connector coupling point where the rigid pipe meets the flexible metal conduit supplying the generator. The threaded metal fittings showed significant rust deterioration and weathering from outdoor exposure, which compromised the integrity of the gas line connection. Documented the corroded components and deteriorated mounting hardware with photographic evidence showing the extent of rust damage on the vertical supply pipe, valve assembly, and coupling connections. The installation showed signs of prolonged moisture exposure with biological growth on surrounding surfaces, contributing to accelerated corrosion of the gas line components.

Diagnosed HVAC system with inoperative blower and discovered blown 30-amp fuses supplying power to the blower motor. Upon further inspection, identified heat damage to the electrical disconnect box, indicating excessive current draw or poor connections. Measured electrical current at 52 amps using clamp meter, confirming overload condition. Determined blower motor module failure as root cause of fuse failure and heat damage. Ordered replacement blower motor module under warranty coverage and new disconnect box as non-warranty repair. Coordinated parts delivery and scheduled follow-up installation after components arrived. Documented electrical measurements and heat damage with photographs for warranty claim and customer records.

Completed scheduled maintenance on 8-year-old York air conditioning system. Performed comprehensive inspection of outdoor condensing unit, verified proper operation of all electrical connections at junction box, and confirmed system functionality. Unit operating within normal parameters with no issues identified during routine preventative maintenance visit.

Completed scheduled preventive maintenance on residential air conditioning system. Inspected outdoor condensing unit, verified proper operation of all electrical components at breaker panel, and confirmed system functionality. Unit showed signs of vegetation encroachment which was noted for ongoing monitoring.

Completed scheduled MVP cooling maintenance visit on outdoor condensing unit. Performed standard system inspection, verified proper operation of all components, and documented equipment condition with unit showing normal wear consistent with outdoor exposure. Refrigerant lines and electrical connections inspected and found secure with no immediate service concerns noted.

Completed scheduled cooling system maintenance visit. Performed comprehensive inspection of outdoor condensing unit including electrical disconnect switch, control wiring, and internal electrical components. Verified proper operation of safety disconnect mechanism and examined all wire connections within the unit's electrical compartment. All electrical connections found secure with appropriate wire terminations. System operational and ready for continued service.

Completed scheduled cooling maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified proper operation of compressor and fan motor, checked refrigerant levels, and cleaned condenser coils. Unit operating within normal parameters with no issues identified.

Completed MVP air conditioning maintenance service. Performed comprehensive system inspection including internal components, checked refrigerant levels, inspected electrical connections, and verified proper operation of all mechanical parts. Unit found to be operating within normal parameters with no immediate service needs identified.

Completed MVP cooling maintenance visit on outdoor condenser unit. Upon arrival, found the top cover severely damaged with protective covering torn and peeling away, exposing internal components, and significant debris accumulation including dead leaves and organic matter around the base and on top of the unit. Performed thorough cleaning of condenser coil fins, removed all accumulated debris from unit exterior and surrounding area, and assessed overall system condition as part of recurring maintenance service.

Completed tankless water heater replacement, removing existing unit and installing new Rinnai tankless system. Installation included mounting unit to wall, connecting copper water supply lines with brass shut-off valves and pressure gauge, routing PVC exhaust venting through ceiling, connecting yellow flexible gas line, and establishing electrical connections. System tested and operational at 120 degrees, with all connections verified for proper function and leak-free operation.

Completed warranty replacement of electric water heater in basement utility area. Retrieved water heater kit from shop and picked up pre-ordered parts from Ferguson supply house as scheduled. Installed new electric water heater with proper copper piping connections, pressure relief valve, and expansion tank mounting, ensuring all connections were secure and system was operational alongside existing water treatment equipment.

Responded to no power call at residential property. Upon arrival, inspected main electrical panel and circuit breakers in basement utility area. Found tripped breakers and reset affected circuits. Verified proper breaker operation and tested electrical system functionality. Confirmed power restoration to all areas of home and ensured panel components were secure and properly functioning.