Your Trusted HVAC, Plumbing & Electrical Experts in Wadsworth, OH

# Service Summary Responded to no-heat call on 7-year-old residential gas furnace. Upon arrival, performed diagnostic inspection of unit and internal components to identify cause of heating failure. # Work Performed Accessed furnace control compartment and conducted systematic troubleshooting of electrical and ignition systems. Inspected all internal components including control board, wiring harnesses, capacitors, and safety switches. Tested voltage and continuity at key connection points to isolate the malfunction. Identified failed component preventing furnace operation. Replaced defective part and verified proper electrical connections throughout the system. Restored power to unit and cycled furnace through complete heating sequence to confirm ignition, flame sensing, and blower operation. Verified proper airflow through supply plenum and ductwork system. Conducted final system test to ensure furnace achieved and maintained call for heat. Confirmed all safety controls function

Performed routine maintenance on 5-year-old furnace, including inspection and cleaning of blower wheel which showed significant dust accumulation on lower section. Used hex key tool to make necessary adjustments to system components, restoring optimal airflow and efficiency.

Diagnosed 17-year-old Generac generator that was starting but failing to supply power to the residence. Inspection of electrical panels revealed issues with the transfer switch connections and deteriorated wiring insulation in the control box. Repaired faulty connections and replaced damaged wiring to restore proper functionality.

Diagnosed and serviced a 15-year-old heating system that was not producing heat. Upon inspection of the furnace interior, found electrical issues affecting the blower motor and control board which were repaired to restore proper heating function. System was fully tested to confirm normal operation before completing service.

Identified and repaired a faulty bedroom circuit that was causing repeated breaker trips. Inspection revealed improper wire connections at the junction box, with exposed copper conductors and loose terminations. Rewired the connections according to code, secured all terminations, and verified circuit stability under load testing.

Performed comprehensive tune-up on 6-year-old furnace, including inspection of electrical components and control board. Opened unit to check wiring connections, examined fan motor assembly for proper operation, and inspected heat exchanger for signs of rust/corrosion. All systems tested and verified to be functioning within normal parameters.

Responded to a no power call following a storm where customer experienced partial power initially before complete loss. Upon inspection of the electrical panel, identified the main disconnect switch as the source of failure. Replaced faulty main breaker and restored full power to the residence.

Reconnected internal toilet components in 40-year-old home. Inspected tank mechanism including float ball assembly and flush valve. Completed service and tested for proper functionality.

Inspected property and identified outdated outlets requiring replacement along with an exposed live wire on the exterior of the home. Installed GFCI outlets to bring electrical fixtures up to current safety standards and properly secured the hazardous exterior wiring to eliminate shock risk.

Performed routine heating maintenance on 16-year-old HVAC system. Inspected blower motor assembly and electrical connections, documenting all components with photos. Confirmed proper operation of residential heating unit.

Conducted assessment of 50-gallon power vent water heater requiring replacement. Provided quote for new natural gas MVP water heater with power vent capability. Documented existing installation environment in basement utility area with proper venting and connection points for efficient replacement planning.

Performed scheduled furnace tune-up, identifying that filter replacement was due. Inspected blower wheel assembly which showed normal wear patterns and some residue buildup. Utilized Draper diagnostic equipment to complete the maintenance service.

Successfully completed the rebuild of the house side water line by eliminating the leaking meter horn above the main water shut off valve. Installed new meter spuds, adapted to CPVC, added a new shut off valve, and reconnected to the outlet side, resolving the leak issue as confirmed by the water department's recommendation.

Completed heating system maintenance on unit of unknown age. Inspected ductwork, insulation, and drainage components in utility area. Checked quarter-turn ball valve with proper thread seal tape on supply line; system functioning normally after service.

Performed scheduled MVP furnace maintenance service. Inspected furnace system components including ductwork, connections, and water heater installation. Examined control board and electrical connections, verifying all wiring harnesses were properly secured and functioning normally. All systems operating within normal parameters.

Responded to service call for 12+ year old gas furnace that was shutting off intermittently following a power outage. Upon inspection, found the control board had failed due to power surge damage. Replaced circuit board, verified proper connections of all wiring harnesses, and conducted full system test with multiple heating cycles to confirm reliable operation.

Performed scheduled MVP Heating maintenance service. Inspected electrical control panel components including PCB, wire harnesses, and terminal connections. Noted minor A/C condensate leak which appears infrequent and minimal; will continue to monitor condition.

Responded to no heat call for a 25-year-old furnace. Diagnosed faulty ignition control module with corroded connector pins. Replaced electronic control board and verified proper system operation, restoring heat to the home.

Performed scheduled heating maintenance on a Lennox furnace system. Inspected and evaluated the filter condition, noting some dust accumulation. Completed comprehensive system check including examination of PVC venting, refrigerant lines, electrical connections, and condensate drainage components to ensure proper operation for the heating season.

Performed scheduled maintenance on heating system. Inspected control board and electrical connections, noting all components functioning properly. Observed significant copper line oxidation and corrosion at heat exchanger connection; cleaned affected areas and verified proper operation of system.