Your Trusted HVAC, Plumbing & Electrical Experts in Wadsworth, OH

Performed an on-site evaluation for a standby generator replacement, as the existing Generac unit is aged and not operating properly. Inspected the main electrical service panel, including the breaker layout, circuit directory labeling, available breaker spaces, and panel condition, and documented water staining on the directory strip along with an AFCI-protected circuit. Gathered the information needed to size and quote a new generator installation with transfer switch connection.

Performed seasonal heating maintenance on the gas-fired furnace, including a combustion analysis that showed O2 at 6.4%, CO at 42 ppm, CO2 at 8.2%, and steady-state efficiency of 93.8%. Inspected the integrated control board, wiring harness, and low-voltage connections, finding no signs of corrosion, frost, or physical damage. The system was operating within normal parameters at completion.

Performed annual heating maintenance on the furnace, including inspection of the control board and ECM drive circuitry, verification of wiring connections and terminal strip integrity, and examination of the power module and heat sink for proper operation. Checked the humidifier and cooling control relays and confirmed all components were secure and functioning within normal parameters. Inspected and utilized a bent probe tool to access and verify internal furnace components, ensuring the system is operating safely and efficiently.

Performed MVP furnace maintenance on an upright gas furnace with attached evaporator cabinet, including inspection of the Lennox integrated control board, wiring harnesses, and connections for signs of burning, corrosion, or damage. Verified condensate drain and PVC venting and ductwork were intact and free of leaks, frost, or rust, and confirmed the filter and system documentation were in place. Unit was left in good working condition with no deficiencies noted.

Completed scheduled heating maintenance on a 2-year-old Bryant Plus 90t furnace system. Performed comprehensive inspection of all internal components, burner assembly, heat exchanger, blower motor, and electrical connections. Verified proper operation of all safety controls, checked airflow, and confirmed system is functioning within manufacturer specifications with no issues identified at this time.

Replaced 3/4" mixing valve, ball valve, and associated piping at walk-in tub installation. Installed new Flexlite pressure tank with tee package and connecting piping, integrating system with existing water treatment equipment including filtration units. Routed blue PEX supply lines through ceiling joists and secured with appropriate clips. All necessary parts were coordinated through suppliers and delivered to complete installation. System tested and verified operational upon completion.

Completed routine maintenance and tune-up on three-year-old furnace located in basement. Performed comprehensive inspection of all system components including control board assembly, electrical connections, and multi-pin connector interfaces. Verified proper operation of integrated circuits, capacitors, and control circuitry. Inspected all wire connections and harnesses for secure attachment and proper routing. All components found to be functioning within normal parameters with no deficiencies noted. System operating as designed with maintenance now current through 2026.

Completed annual maintenance on 8-year-old boiler system that had been rescheduled from October 2nd. Performed comprehensive inspection of burner assembly, heat exchanger, and all associated components. Inspected burner tubes and brass fittings, noting normal accumulation of dust and surface oxidation consistent with system age. Examined finned heat exchanger coil and found moderate dust buildup on surfaces. Verified integrity of all electrical connections including visible wiring harnesses and mounting hardware. Checked gas piping connections and brass fittings for proper seating and signs of wear. All components found to be functioning within normal parameters for unit age and operating conditions.

Completed comprehensive MVP heating maintenance inspection and system evaluation. Thoroughly examined and photographed blower assembly components, including squirrel cage fan wheel and motor bearing assembly, confirming clean operation and proper mechanical condition with no debris accumulation or wear indicators. Inspected control board and electrical connections within the air handler, verifying all wire terminations, circuit board integrity, and safety systems are functioning correctly with no signs of overheating, corrosion, or component failure.

Completed recurring MVP heating maintenance visit on residential HVAC system. Performed comprehensive inspection of gas furnace and blower assembly, documenting condition of blower wheel which showed moderate dust and dirt accumulation on fan blades and housing. Verified proper operation of heating equipment, water heater connections, and associated venting systems including PVC condensate drainage lines.

Completed scheduled MVP heating maintenance visit. Performed comprehensive system inspection including visual assessment of motor and compressor assembly components, noting surface oxidation on mounting brackets and fasteners consistent with normal aging. Conducted internal ductwork inspection using camera equipment, documenting interior conditions with temperature reading of 118°F at time of inspection. All mechanical components operational and system functioning within normal parameters.

Completed installation of 24kW Generac home standby generator with 200-amp automatic transfer switch and whole home surge protector. Installed oil warmer for cold weather operation. Ran approximately 20 feet of electrical conduit from main service panel to generator location and coordinated with gas line contractor for 30 feet of natural gas supply line installation. Mounted generator on exterior concrete pad adjacent to house, installed gray electrical panel and white Generac transfer switch on vinyl siding with proper clearances. Routed white PVC and gray conduit along exterior wall using appropriate fittings and supports. Configured system for whole-home backup power operation without requiring utility disconnect. All electrical connections completed per NEC standards and manufacturer specifications. System tested and operational upon completion.

Completed comprehensive MVP furnace maintenance on residential Lennox heating system, including full inspection of unit components, burner assembly, heat exchanger, and PVC intake/exhaust venting configuration. Verified proper operation of all safety controls, tested system performance, and confirmed efficient heating cycle with no issues detected.

Completed installation of 90% AFUE gas furnace and air conditioning system. Installed new ductwork with proper sealing at joints and connections, mounted outdoor condensing unit on pad with appropriate clearances, and ran refrigerant lines and electrical disconnect. Verified all components operational, system charged to manufacturer specifications, and confirmed proper airflow throughout the system.

Responded to service call for reported water leak near water treatment equipment. Upon inspection, determined that the water softener and pressure tank system were not the source of the leak. Located actual leak source in ceiling above the water softener, where plumbing connections showed signs of water discharge. Documented conditions with photographs showing standing water on basement floor around equipment and identified overhead piping with PEX and PVC connections requiring attention. Customer unable to access basement for personal inspection due to mobility constraints.

Completed MVP Cooling Maintenance on HVAC system. Performed thorough inspection of evaporator coil assembly, noting normal condensation on drain pan and minor dust accumulation on aluminum fins. Examined control board components including DIP switches, circuit connections, and LED display showing proper operational status. All system components found to be functioning within normal parameters.

Performed site assessment and provided estimate for installation of natural gas line to power standby generator. Evaluated existing gas meter location and determined optimal routing path from meter assembly to proposed generator placement area. Documented current gas infrastructure including aged copper piping with visible corrosion and patina, existing meter connections, and protective bollards. Assessed wall penetration requirements through white brick exterior and measured distances for material calculations. Generator unit to be supplied by property owner. Provided comprehensive estimate covering gas line installation, required fittings, pressure testing, and connection specifications per local code requirements.

Responded to lightning strike damage affecting multiple light fixtures throughout the residence. Replaced damaged recessed light fixture in bedroom, installed new closet light fixture, and replaced rear deck floodlight. All fixtures tested and verified operational upon completion of installation.

Completed scheduled maintenance on residential standby generator unit. Performed visual inspection of equipment exterior, verified proper operation of control panel indicators including run status light, and confirmed unit is in good working condition with all components functioning as designed.

Responded to customer complaint of rattling and banging noises occurring intermittently during washing machine fill cycles and occasionally when shower is running. Upon arrival, inspected main water supply plumbing system and identified water hammer condition caused by inadequate air cushioning in the supply lines. Examined vertical copper pipe assembly including main shutoff valve, pressure regulator, and associated brass fittings for proper operation and secure mounting. Verified pressure gauge readings were within normal parameters and confirmed all compression fittings and connections were tight with no visible leaks. Assessed condition of existing plumbing infrastructure, noting aged copper piping with minor surface oxidation but structurally sound. Documented installation with photographs showing complete plumbing assembly, pressure regulation equipment, and valve configuration for service records.