HVAC, Plumbing & Electrical Services in Barberton, OH

Completed scheduled MVP preventive maintenance heating visit on furnace system. Performed comprehensive inspection of heating unit, documented control board wiring and diagnostic information with photos, and provided customer with additional air filter for future use. All components operating within normal parameters at time of service.

Responded to service call for sump pump drainage failure in basement with dual pump system. Upon inspection, identified non-functioning primary sump pump preventing proper water evacuation from pit. Diagnosed issue, performed necessary repairs to restore pump operation and verified proper drainage function. System tested and confirmed operational with both pumps discharging correctly through existing PVC discharge lines.

Performed routine maintenance flush on a 3-4 year old electric tanked water heater. Drained sediment buildup from tank bottom through drain valve, flushed system with cold water supply until discharge ran clear, and inspected all plumbing connections including copper supply lines and shut-off valves for proper operation. Verified temperature and pressure relief valve functionality, checked anode rod condition, and confirmed water heater was heating properly after refilling. All components operating within normal parameters with no leaks detected at connections or fittings.

Completed spring maintenance and tune-up on Carrier outdoor condensing unit. Inspected control board, electrical connections, and wiring harness; all components found in good operational condition. Noted vegetation overgrowth around unit base and recommended clearance maintenance for optimal airflow and efficiency.

Completed preventative maintenance tune-up on 6-7 year old residential air conditioning system. Performed comprehensive inspection of air handler unit including blower wheel assembly, electrical components, and condensate drain lines. All system components found operating within normal parameters with no deficiencies noted at time of service.

Completed heating system tune-up and performance evaluation. Performed combustion analysis on natural gas furnace using Bacharach Fyrite InTech analyzer, confirming optimal operating parameters with 98.4% efficiency, O₂ at 9.3%, CO at 13 ppm, and CO₂ at 6.5%. Measured electrical amperage draw at 5.16 amps using digital clamp meter to verify proper motor operation and system performance within manufacturer specifications.

Completed MVP cooling maintenance visit on Lennox residential air conditioning system. Upon inspection, discovered severe ice buildup on evaporator coil assembly and refrigerant lines inside air handler unit, indicating restricted airflow or low refrigerant charge. Documented system condition with photos showing frozen copper lines and iced coil fins. Exterior condenser unit operating, properly mounted on concrete pad with electrical connections and refrigerant lines secured. Further diagnostics required to determine root cause of freezing condition and restore proper system operation.

Completed plumbing repair in attic and crawl space areas involving copper pipe installation and replacement. Ordered necessary parts through warehouse with delivery coordination, managing backorder items until all components arrived. Installed new copper piping with proper support straps, hangers, and insulation foam where required, connecting to existing drainage lines and ensuring proper integration with PVC plumbing system and structural framework.

Completed MVP recurring cooling maintenance visit on residential HVAC system located in crawl space/basement area. Performed comprehensive inspection of air handler unit, ductwork, refrigerant lines, and condensate drainage system. All components found operating within normal parameters with appropriate condensation present on supply duct indicating active cooling mode. Verified proper operation of system controls and status indicators. Documented equipment condition through photographic records showing air handler cabinet, insulated refrigerant lines with proper connection caps, PVC condensate drain lines, and sealed ductwork connections.

Replaced leaking Bradford White 50-gallon power vent water heater with new Bradford White 50-gallon power vent unit featuring 8-year manufacturer warranty. Installed new thermal expansion tank, retained existing cold water ball valve, eliminated electric anode rod, reworked hot water connections, and tied into existing exhaust vent pipe.

Completed water line installation and connection to Rheem Performance tanked water heater. Connected hot and cold water supply lines using copper piping with shut-off valves featuring red handles installed at the top of the unit for proper water flow control and future maintenance access. All connections were secured with threaded fittings and compression nuts to ensure leak-free operation, and the unit was verified to be properly positioned and ready for service.

Completed comprehensive AC tune-up on 8-year-old system, including inspection of evaporator coil and blower assembly. Found significant dust accumulation on blower wheel and blades, along with visible corrosion and rust buildup around copper refrigerant line connections at evaporator coil; cleaned components and documented condition with photos for maintenance records. System operational upon completion of preventative maintenance service.

Completed full HVAC system installation including 80% AFUE furnace and air conditioning unit in basement utility area. Installed new air handler with proper electrical connections and junction box wiring. Ran refrigerant lines with appropriate insulation wrapping from condensing unit to air handler. Installed PVC condensate drain piping with proper pitch and mounting brackets secured to wall framing. Connected flexible metal conduit for electrical service and mounted all components to manufacturer specifications. Routed metallic flexible ductwork for supply air distribution. System tested and operational upon completion.

Completed scheduled MVP air conditioning maintenance on Heil outdoor condenser unit. Performed comprehensive system inspection including electrical connections at attic-mounted control box, verified proper operation of all components, and documented equipment condition with photos showing unit in good working order with no visible deficiencies noted.

Responded to warranty callback for Lennox AC unit making unusual noises upon first seasonal startup. Unit was installed five months prior but had not been operated until customer activated system. Performed comprehensive inspection of outdoor condenser unit, checking all mechanical components, fan operation, and securing hardware. Identified and resolved noise issue by tightening loose fan guard mounting hardware and verifying proper fan blade clearance. Tested unit operation through full cooling cycle to confirm normal sound levels and proper system performance. System now operating within manufacturer specifications with no abnormal sounds present.

Responded to emergency call for busted pipes in basement utility area. Upon arrival, discovered significant water damage to flooring with multiple deteriorated layers and extensive staining indicating prolonged moisture exposure. Assessed compromised plumbing infrastructure with visible pipe deterioration and accumulated debris throughout affected space. Documented conditions showing water-damaged subflooring, discolored wood panels, and compromised structural materials requiring immediate attention to prevent further damage.

Completed installation of a 90% efficiency furnace and air conditioning system in basement mechanical room. New furnace unit was positioned and connected with metal supply ductwork and flexible ducting for proper air distribution throughout the structure. Electrical connections were terminated and new FLNR 25A time-delay dual element fuses were installed in the disconnect for overcurrent protection per manufacturer specifications. All ductwork transitions were secured, refrigerant lines were connected to the outdoor condensing unit, and system was tested for proper operation. Installation included proper clearances from existing water heater and integration with existing infrastructure in unfinished basement space.

Completed MVP recurring cooling maintenance visit on HVAC system. Performed thorough inspection of evaporator coil assembly, which showed normal dust accumulation on aluminum fins and serpentine refrigerant tubing. Examined air handler unit interior components including control boards, wiring harnesses, and electrical connections—all found to be in proper working condition with secure connections and no signs of overheating or component failure. System operational and functioning within normal parameters.

Completed promotional A/C tune-up service on residential cooling system. Connected manifold gauges to service ports to verify refrigerant pressures and system operation. Inspected and removed electrical fuses from disconnect box for examination, confirming proper amperage rating and blade condition before reinstallation. All components found operating within normal parameters upon completion of tune-up procedures.

Responded to customer concern regarding recently replaced outlets and potential open neutral condition. Performed comprehensive electrical safety inspection of affected circuits during active renovation work. Tested outlet wiring connections and verified proper neutral and ground continuity throughout the circuit. Confirmed no hazardous wiring conditions present. Documented existing conditions with photos showing exposed electrical boxes in walls during construction phase. Provided technical assessment confirming electrical system safety and discussed options for any additional work needed as renovation progresses.