Heating, AC, Plumbing & Electric in Bedford, OH

Completed installation of 80% AFUE gas furnace in residential mechanical room. Unit installed with proper metallic ductwork connections, gas line hookup, and venting system. Installed new Kidde carbon monoxide alarm as required safety measure for combustion appliance installation. All equipment positioned and secured per manufacturer specifications and local code requirements.

Responded to no-heat call on 15-year-old gas furnace with reported humming noise upon startup. Upon inspection, found extensive dirt and debris accumulation throughout the unit's interior components, including control module, blower compartment, and ductwork connections. The heavy buildup of dust and grime on electrical components and surrounding surfaces indicated prolonged operation without proper maintenance, which was contributing to operational issues. Assessed system condition, documented equipment state with photographs showing significant contamination on control boards and mechanical housing, and provided recommendations for thorough cleaning and maintenance to restore proper function and prevent future failures.

Responded to service call for air conditioning system with reported refrigerant leak. Performed comprehensive diagnostic evaluation of existing Trane furnace and dual outdoor condenser units installed on brick paver pad adjacent to residence. Assessment revealed active refrigerant leak in AC system requiring repair, humidifier component needing replacement, and potential furnace issues warranting further evaluation. Provided detailed estimate for complete HVAC system replacement including new furnace, air conditioning equipment, and associated components to address multiple system deficiencies and ensure reliable climate control operation.

Responded to service call for non-functioning water heater that required electrical verification following previous unsuccessful repair attempt. Inspected electrical panel, junction box, and associated wiring in utility room to diagnose power supply issues affecting water heater operation. Verified electrical connections and circuit integrity to mechanical equipment, documented existing conditions with photos showing panel configuration and utility room electrical infrastructure.

Responded to service call addressing multiple plumbing concerns including a stuck hose fitting on exterior spigot, frequently clogging floor drain, and non-functioning water heater. Inspected outdoor spigot mounted on foundation where hose end was seized to the connection point. Assessed electrical panel and water heater system to diagnose heating failure. Documented site conditions with photographic evidence showing exterior spigot location on brick and vinyl siding foundation area, as well as electrical panel configuration for water heater troubleshooting purposes.

Responded to no cooling complaint on 21-year-old air conditioning system. Upon arrival, performed diagnostic testing using digital multimeter to measure electrical values and system performance. Also inspected 23-year-old furnace and humidifier as requested, as these components had not been serviced recently and customer was concerned about their operational status.

Replaced existing garage floodlight fixture with customer-provided dual-head LED motion sensor security light on exterior metal building. Removed old fixture, installed new mounting hardware, connected electrical wiring to the dual-head unit with central motion detector, and verified proper operation of both LED light heads and motion sensing functionality.

Completed MVP air conditioning maintenance service. Inspected and tested electrical components including time-delay fuses rated at 250V in outdoor disconnect, verified proper amperage ratings and fuse integrity. Performed electrical diagnostics using clamp meter to measure current draw on system wiring, confirmed normal operating parameters within manufacturer specifications. All electrical connections, wiring, and safety components found in satisfactory working condition.

Responded to no-cooling complaint on newly installed Lennox system. Upon arrival, confirmed outdoor condensing unit fan motor was not operating. Diagnosed failed capacitor preventing compressor and condenser fan operation. Replaced defective dual-run capacitor with OEM replacement part, restoring proper system function. Verified correct amperage draw on both compressor and fan motor, confirmed adequate refrigerant charge, and tested system through complete cooling cycle. Unit now operating within manufacturer specifications with proper airflow and temperature differential across evaporator coil.

# HVAC Install - Complete System ## Summary Completed full HVAC system installation including 90% efficiency furnace with humidifier and matching air conditioning unit, verified proper venting installation to ensure flues are not cellular core construction. ## Work Performed Installed complete residential heating and cooling system in basement mechanical room and exterior location. System consists of Trane brand furnace unit with integrated humidifier and corresponding outdoor condensing unit. **Indoor Equipment Installation:** - Mounted gray metal furnace unit on concrete basement floor - Connected white PVC intake and exhaust venting from furnace, routing upward through structure - Verified all flue pipes are appropriate non-cellular core material per code requirements - Installed electrical connections with proper wiring run along installation perimeter - Connected silver metallic supply ductwork to furnace plenum - Positioned tall air handler unit adjacent to furnace with prope

Completed MVP Cooling Visit on a 2-year-old Lennox EL17XC1-030-230A02 system containing HFC-410A refrigerant with a factory charge of 6 lbs 8 oz. Performed comprehensive maintenance inspection of both indoor and outdoor units. Verified electrical specifications are within acceptable parameters (208/230V nominal, MIN 197, MAX 253). Inspected outdoor condenser unit positioned on concrete pad, noting environmental debris accumulation and vegetation growth in surrounding area. Evaluated wall-mounted electrical disconnect box and associated conduit connections for proper operation. Documented equipment specifications including compressor ratings and fan motor specifications (0.7 FLA, 1/8 HP). Recommended installation of surge protector on motherboard to safeguard against electrical surges from home power supply or furnace-generated fluctuations. System operational and performing to manufacturer specifications upon completion of maintenance visit.

Responded to service call for multiple electrical issues including blown circuit requiring split, non-functioning kitchen outlet, and garage motion detector with suspected improper wiring. Inspected electrical panel, identified tripped breaker, and assessed circuit loading to determine need for circuit split to accommodate two customer-supplied light fixtures requiring installation. Troubleshot and corrected motion detector wiring in garage and restored power to inoperative kitchen outlet.

Conducted comprehensive HVAC system evaluation for equipment replacement estimate. Assessed existing gas furnace/air handler unit located in basement utility area, including connected ductwork distribution system, copper refrigerant lines, and electrical connections. Evaluated outdoor condensing unit positioned on concrete pad adjacent to building foundation, inspecting refrigerant line sets, electrical conduit routing, and overall system configuration. Documented current equipment specifications, installation conditions, and provided replacement recommendations based on system age and performance requirements.

Installed GFCI outlet in upstairs bathroom per customer request, replacing standard receptacle to provide ground fault protection in wet location as required by electrical code. Coordinated arrival time with customer's wife due to homeowner being unavailable during service call.

Responded to service call regarding electrical concerns following recent roof work. Performed comprehensive inspection of exterior electrical panel and associated systems. Panel inspection revealed proper circuit breaker configuration with no immediate safety hazards observed. Verified all branch circuit connections, main breaker functionality, and panel integrity. Examined exterior conduit penetrations and junction points near roofline to ensure no damage occurred during roofing operations. All electrical connections found secure with no loose wiring or compromised conductors. Documented panel conditions and surrounding utility infrastructure with photographic evidence for record.

Completed MVP recurring cooling maintenance visit on 4-year-old Lennox HVAC system. Inspected furnace unit, ductwork, refrigerant lines, electrical components including capacitor and contactor, and verified proper system operation. Documented equipment condition with photos showing normal wear and minor debris accumulation in outdoor unit; all components functioning within normal parameters.

# HVAC Service Report ## Summary Responded to no-cool complaint on 3-year-old AC system. Diagnosed failed contactor with severe contamination and burn damage, replaced contactor and damaged line set section, restored system to normal cooling operation. ## Work Performed Upon arrival, found AC system completely non-operational with no power to outdoor condensing unit. Visual inspection revealed contactor assembly heavily contaminated with dust, dirt, and carbon deposits indicating electrical arcing and overheating. Terminal connections showed significant discoloration and tarnishing, with evidence of sustained arcing damage to contact surfaces. Performed electrical testing and confirmed contactor failure as primary cause of system shutdown. Contacts were welded together from excessive current draw, preventing proper cycling. Brass terminal screws exhibited heat damage and oxidation consistent with poor electrical connection over time. During outdoor unit inspection, discovered refr

Completed installation of 80% efficiency furnace and air conditioning system in attic location. Installed new furnace unit with proper venting and exhaust piping, connected gas lines with appropriate securing, and integrated air handler with metallic supply ductwork. Installed outdoor condensing unit with proper electrical connections including 25-amp fused disconnect, ran refrigerant lines between indoor and outdoor equipment, and verified all electrical wiring and safety controls are functioning correctly per manufacturer specifications.

Performed comprehensive cooling system tune-up and preventative maintenance on properly functioning HVAC unit. Conducted electrical diagnostics using digital multimeter, measuring system amperage at 8.68A and verifying voltage readings to ensure equipment operating within manufacturer specifications. All components inspected and found to be functioning correctly with no issues identified.

Responded to hail damage assessment request for outdoor mini-split condenser unit. Conducted thorough visual inspection of equipment, documenting extensive rust staining on fan guard and top rim, along with weathered concrete pad showing algae growth. Performed electrical diagnostics using digital multimeter to verify system functionality and assess potential component damage from hail impact. Documented unit condition with photographs and provided customer with detailed repair quote based on findings.