Trusted HVAC, Plumbing & Electrical Services in Clinton, OH

Installed a customer-supplied wall-mounted garage heater, including mounting, connection of the unit, and roof penetration with vent pipe and flashing for exhaust venting. Performed a post-installation inspection and used a digital meter to verify proper operation, with no visible frost, rust, or other anomalies observed.

Installed a new 80% AFUE gas furnace with a galvanized flue connected to the existing masonry chimney, and reconnected the gas supply through a shutoff valve and the condensate/drain piping. Installed an AprilAire media air filter cabinet, verified static pressure across the filter with a digital manometer, and sealed the sheet metal duct seams with foil tape. Also installed a whole-home surge protector.

Performed an on-site furnace replacement estimate, evaluating the existing equipment area in the unfinished basement, including the Honeywell Home whole-house humidifier mounted on the supply plenum with flexible duct and control wiring, and noting no visible rust, frost, or cracking. Documented the adjacent main electrical panel and surrounding wiring, copper piping with shutoff valve, and available clearances for the new installation. Photos were captured to support equipment sizing and replacement scope.

Performed a complete duct cleaning on a ranch-style home's supply and return system (under 14 vents), removing heavy accumulations of dust, debris, and cobwebs from the trunk lines and branch runs. Documented severely deteriorated duct lining and a breach in the duct wall exposing the masonry beneath, and recommended repair or replacement of the damaged sections to prevent further debris intrusion and air leakage.

Installed a Navien tankless water heater on a plywood backer board mounted to the masonry wall, with new press-fit copper supply and return piping, isolation valves for service flushing, and an expansion tank. Terminated the PVC venting and condensate/combustion piping through the exterior brick wall, then verified that all connections were secure and leak-free.

Performed an on-site estimate for replacing the existing power-vent tank-style water heater with a tankless unit, and evaluated relocating a furnace to the garage. Inspected the existing Smith water heater, PVC exhaust venting, expansion tank, copper supply piping with isolation valve, condensate/drain routing, and electrical connections, and found no visible leaks, rust, or damage. Documented the mechanical room layout with photos to determine gas, venting, and water line requirements for the tankless installation.

Performed a recurring heating maintenance inspection on the gas-fired furnace, including combustion analysis with a calibrated analyzer (CO 28 ppm, CO2 7.2%, stack temperature 108°F) and electrical testing of the inducer and blower motor circuits with a true RMS clamp meter. Inspected the gas valve, control board, wiring harness, and condensate/vent piping; components were dusty but showed no signs of rust, frost, or damage, and the unit is operating normally.

Performed MVP heating maintenance, including inspection of the gas furnace cabinet, gas valve assembly, inducer motor, and control board wiring. Inspected the blower wheel, which showed noticeable dust and debris accumulation on the blades, and noted light corrosion on the internal divider shelf near the inducer motor along with loose, disorganized low-voltage wiring in the lower compartment. Documented all findings with photos for system records.

Performed duct cleaning on the galvanized sheet metal supply trunk, removing accumulated dust, debris, and reddish-brown residue from the duct floor and seams. Inspected the interior and documented a section of broken wood paneling at the duct ceiling opening, recommending repair or replacement to restore system integrity and airflow.

Responded to a service call for a heat pump system delivering lukewarm air at the supply registers despite reaching setpoint. Inspected the air handler/furnace cabinet, ductwork, and surrounding equipment, finding no visible damage, frost, or corrosion. Further diagnostics of the heat pump's refrigerant circuit, reversing valve, and auxiliary heat operation are recommended to determine the cause of reduced heating output.

Performed a descaling flush and refill of the Rinnai wall-mounted tankless water heater by isolating the unit, circulating flushing solution through the heat exchanger to remove mineral buildup, then rinsing and restoring service. Verified proper operation after refill, with no visible leaks, corrosion, or equipment damage observed at the unit or supply piping.

Performed seasonal heating maintenance on a 5-year-old system, including inspection and cleaning of the blower wheel to remove accumulated dust and debris for improved airflow and motor efficiency. Inspected the humidifier water panel and found heavy mineral and rust scaling, which reduces humidification performance, and recommended panel replacement and routine cleaning of the housing.

Delivered and placed two bags of solar salt for the water softener brine tank during a scheduled maintenance visit, and supplied a replacement pleated sediment filter cartridge for the whole-house filtration system. System inspection found the softener, control valve, and PEX supply lines in good condition, with no leaks, rust, or corrosion observed.

Performed scheduled heating maintenance on the gas furnace, inspecting the inducer motor, gas valve, and control wiring for secure connections and proper condition. Removed the flame sensor, which showed corrosion and carbon buildup, and cleaned it to restore reliable flame sensing and ignition performance.

Responded to a callback to complete a previously diagnosed dripping faucet repair, installing the manufacturer-supplied replacement Moen cartridges and associated seals and O-rings that had been ordered for the fixture. Removed the worn, debris-laden cartridges and installed the new components, restoring proper faucet operation and eliminating the drip.

Delivered water softener salt to basement location and loaded brine tank for customer with mobility limitations. Verified proper salt level in softener system that was previously installed in May. System inspected and confirmed operational with adequate salt supply for continued water treatment.

Completed routine preventative maintenance on residential Generac standby generator unit located outside near garage. Inspected and serviced dual battery system, verifying proper terminal connections and cable integrity. Documented battery compartment condition showing normal weathering and minor dust accumulation consistent with outdoor installation, with all electrical connections secure and functional.

Completed electrical estimate for standby generator installation. Assessed existing outdoor generator pad location and mounting frame structure, evaluating site conditions including clearances and environmental factors. Inspected current electrical service panel configuration, documenting existing bus bar connections, terminal blocks, and available breaker positions to determine proper integration point for generator transfer switch and associated circuits.

# HVAC Install - Complete System Completed installation of a 90% efficiency furnace and air conditioning system at residential property. Installed new dark gray air handler unit in basement utility room with proper vertical positioning and clearances. Ran white PVC condensate drain lines and installed black electrical conduit to unit per code requirements. Connected unit to existing ductwork system in basement mechanical room. Exterior work included placement of beige/tan air conditioning condenser unit on ground pad adjacent to building. Mounted gray electrical disconnect box on exterior wall with proper wiring connections. Ran copper refrigerant lines from condenser to indoor air handler, completing refrigerant circuit between components. System tested and confirmed operational with proper airflow and temperature differential across both heating and cooling modes.

Replaced failed air handler unit under manufacturer warranty with new Mitsubishi Electric SVZ-AP48NL system. Upon installation, performed complete system commissioning including refrigerant charge verification and adjustment to manufacturer specifications, and properly dialed in humidity control settings to ensure optimal performance and comfort levels.