HVAC, Plumber & Electrician Services in Fairlawn, OH

Performed maintenance inspection on the gas furnace in response to a reported strong odor resembling hot glue near the control area. Inspected the burner compartment, flame rollout/limit switch, and associated wiring, confirming secure connections and proper burner flame characteristics. No overheated components, damaged wiring, or active source of the odor was identified; the unit was left operating normally.

Performed a diagnostic inspection of the furnace in response to a home inspector's report of a potential issue, using a borescope camera to visually examine internal components and surrounding areas. Imaging captured discoloration and staining consistent with possible moisture, soot, or heat-related residue, which has been documented for further evaluation and recommendations. No operational issues were reported by the homeowner at the time of service.

Performed annual preventive maintenance on a Carrier upright gas furnace, including inspection of the cabinet, PVC vent and condensate lines, gas supply line and shutoff valve, flexible electrical conduit, and supply ductwork connections. All components were found free of visible rust, frost, or damage, and the unit was left operational. Noted that the supply plenum insulation shows minor deterioration with debris along the seams, and recommend monitoring or repair at a future visit.

Diagnosed a 4-year-old Navien tankless water heater requiring replacement of the heat exchanger and main PC board, with both parts covered under manufacturer warranty. Inspected the control board and internal wiring, documenting the unit's condition prior to repair. Parts were ordered and received for the scheduled replacement, which is a lengthy repair; venting was identified as a concern on this unit and should be evaluated during installation.

Performed a seasonal heating tune-up on a 2-year-old Lennox gas furnace in the basement, including inspection of the Aprilaire media air filter and the blower wheel, which was found clean with no debris buildup. System was verified for proper operation under the maintenance membership plan, and the customer's request to remove a previously owned property from the account was noted for processing.

Accessed the main stack clean-out in the basement and ran a drain cable through the main line to clear the blockage. Performed a camera inspection with a locator, which identified a mass of tangled debris, including root intrusion, approximately 23 feet into the line, and confirmed the condition of the pipe wall further downstream at roughly 60 feet.

Performed scheduled heating maintenance on the gas-fired furnace, including a combustion analysis using a Bacharach analyzer. Readings on natural gas showed CO at 24 ppm, CO₂ at 5.5%, O₂ at 11.2%, stack temperature of 419°F, and combustion efficiency of 76.0%, with no visible damage, rust, or abnormal conditions observed.

Performed MVP furnace maintenance, inspecting and servicing the humidifier evaporator pad, which showed mineral and dust buildup, and verifying the supply tubing and housing connections. Removed the dirty Aprilaire 413 media air filter, installed a new replacement, and tagged the unit with a replacement notation for future reference.

Installed a customer-supplied drop-in utility sink and faucet, including cutting the countertop opening to size for the sink. Secured the sink in the cutout and connected the faucet and supply lines for proper operation.

Performed MVP furnace maintenance, including inspection and servicing of the return air filter slot and replacement of the pleated air filter to restore proper airflow. Inspected the Aprilaire bypass humidifier and found the evaporator pad heavily soiled with mineral scale buildup, indicating the pad was due for service.

Performed annual heating maintenance on a 16-year-old natural gas furnace, including inspection of the gas valve assembly, burner compartment wiring, and heat exchanger area. Combustion analysis was completed with the following results: CO at 18 ppm, CO2 at 6.7%, stack temperature of 106°F, and combustion efficiency of 94.0%. Noted heavy surface rust on an internal metal component within the furnace cabinet, which should be monitored at future visits.

Performed MVP furnace maintenance on a gas-fired, condensing furnace, including inspection of the blower assembly, control board, transformer, and low-voltage and line-voltage wiring connections within the cabinet. Verified condensate drain line, PVC intake/exhaust venting, and plenum and ductwork connections, and secured and organized loose wiring and wire nuts in the control compartment. Observed dampness on the floor in front of the unit and recommended monitoring the condensate drain and related connections to ensure proper drainage.

Performed annual maintenance on a 3-year-old natural gas furnace, including a combustion analysis that recorded 7.7% O2, 98 ppm CO, 7.5% CO2, and 80.7% efficiency, and replaced the air filter. Inspected the adjacent Aprilaire whole-house humidifier, its drain line, and the supply plenum, with no frost, rust, or major damage observed.

Performed scheduled heating maintenance on a Lennox furnace, inspecting the air handler cabinet and filter compartment. Found the pleated air filter deteriorated, with frayed and bunched media along its edge, indicating it was restricting airflow and due for replacement. Verified the unit cabinet was clean and intact, with no visible rust, cracks, or damage.

Diagnosed a Navien tankless water heater displaying an error code, inspecting the heat exchanger, control board, gas and water connections, and venting. Serviced the unit and addressed the associated plumbing repair, including reseating and securing the PVC intake/exhaust vent adapters and clamps. Verified proper operation after reassembly.

Performed a routine tune-up on a 5-year-old Lennox gas furnace, including inspection of key components and combustion analysis. Flue gas readings on natural gas showed O2 at 7.6%, CO at 44 ppm, CO2 at 7.5%, and combustion efficiency of 80.8%, with CO within acceptable limits. System operated properly at completion with no major issues noted.

Performed scheduled maintenance on a Bradford White Brute FT combi boiler, inspecting the unit, control interface, and vent/air intake piping. Verified the system following the customer's prior descaling, and inspected the air separator, auto air vent, and associated copper and brass piping, finding no leaks, frost, or visible issues.

Diagnosed a leaking double-handle kitchen sink faucet and replaced the worn cartridges in both handles, restoring proper operation and eliminating the leak. Inspected the under-sink supply lines, shutoff valves, and drain assembly during the repair, and tested the faucet for leaks and function.

Installed two customer-supplied Delta widespread lavatory faucets with new P-traps, along with new oil-rubbed bronze Moen shower trim, waste and overflow trim, and a handheld shower head. Opened the wall behind the tub to install two Webstone ball valves on the tub supply lines for service isolation, then finished the opening with a flat return air cover as an access panel.

Performed scheduled heating maintenance on the furnace, including inspection and cleaning of the blower wheel to remove dust and debris buildup and restore proper airflow. Inspected the control compartment, including the control board, wiring harness, and wire connections, and confirmed the unit is operating properly.