HVAC, Plumbing & Electrical Services in Lakewood

Completed full HVAC system installation in basement utility space, including 80% efficiency furnace unit, air conditioning system, and 40-gallon water heater. Installed and connected metallic spiral ductwork with proper insulation wrapping at connection points, configured rectangular sheet metal ducts and flexible round ducting to furnace unit. Mounted furnace against concrete block wall, integrated humidifier or air quality device with white PVC piping, and ensured all equipment properly positioned and secured with appropriate ventilation routing through exposed ceiling joists.

Completed full HVAC system installation in basement mechanical room, including new furnace/air handler unit and associated components. Installed and connected refrigerant lines, PVC condensate drain and vent piping, and integrated metal ductwork transitioning from rectangular to round configuration extending through ceiling joists. All equipment properly labeled, secured, and tested for operational functionality per manufacturer specifications.

Completed heating maintenance visit for MVP customer. Performed system diagnostics using digital multimeter, recording readings of 3754 on UEi EM2818 instrument while inspecting electrical components, ductwork connections, and gas valve assembly. Inspected blower wheel assembly and housing for proper operation and cleanliness, confirming all mechanical components functioning within normal parameters.

Conducted on-site evaluation for replacement estimate of residential split HVAC system, including both furnace and air conditioning unit, both approximately 10 years old. Assessed existing equipment configuration consisting of basement-installed forced air furnace with plenum assembly and exterior-mounted AC condenser unit positioned beneath wooden deck structure. Documented current system specifications, installation conditions, and equipment placement for comprehensive replacement proposal development.

Replaced corroded section of stack vent by opening additional drywall to expose the vertical run and access sound pipe for proper connection. Removed deteriorated pipe at base and installed new section, securing connection to structurally intact portion of existing stack. Documented existing conditions showing exposed framing, PVC drainage components, and insulation in ceiling cavity prior to repair completion.

Inspected deteriorating stack pipe identified by previous water damage assessment team. Observed black PVC waste pipe with multiple connection points running vertically through wooden joists showing signs of moisture damage. Documented condition of T-junction and connecting fittings where leakage was evident. Prepared detailed quote for replacement of compromised section of drainage system to prevent further structural damage to surrounding wooden framework.

Identified and repaired toilet leak that was previously overlooked, which was causing water to drip into basement electrical box. Inspected toilet base and supply line connection, replaced faulty wax ring and tightened loose fittings to ensure proper seal and eliminate water seepage.

Responded to service call for water leak in upstairs bedroom causing wall cracking. Upon inspection, identified water damage on ceiling with yellowish discoloration and installed protective tarp secured with painter's tape to prevent further interior damage while awaiting comprehensive repair.

Performed scheduled MVP furnace maintenance with confirmed trip. Inspected air filter component and found normal working condition with no visible damage. Observed heat exchanger coils with notable frost accumulation and documented drain pan showing signs of rust and corrosion in the collection tray, which may require future attention.

Performed complete water system upgrade including replacement of multiple 9 1/2" shut-off valves in basement with new ball valves. Coordinated with city water department for main water valve replacement. Installed new Bradford White 50-gallon water heater with thermal expansion tank per code requirements, including 6-year warranty. Replaced outdated 1/2" gas valve to furnace with quarter-turn valve. Successfully cleared drain blockage in third floor tub/shower and installed new waste and overflow assembly.

Completed re-plumbing of the kitchen and upstairs hot water loop to address low flow issues, installing a new manifold system with purge valves and isolation valves for improved sectional control. Replaced water-logged expansion tank with a new 2.1 gallon unit, ensuring proper system pressure regulation and enhanced hot water distribution throughout the property.

Responded to service call regarding leaking plumbing stems for hot and cold water fixtures in bathroom sink. Inspected the bathroom installation featuring six porcelain cross-handle fixtures (three upper and three lower) with signs of normal wear. Further examination of the utility area revealed copper pipes with soldered joints and a central cast iron pipe with two red valve handles controlling water flow through the system.

Diagnosed and repaired water leak in high-efficiency condensing furnace installed by Blynd and Sons. Found damaged condensate drain line with moisture accumulation on concrete floor; replaced PVC condensate piping and sealed connections at furnace exhaust vent to prevent further leakage.

Completed installation of rigid metal dryer vent ductwork in basement laundry area, replacing non-compliant flexible hose to meet city code requirements for electric dryer ventilation. System includes properly sealed 90-degree elbow joints and secure wall mounting for optimal airflow in this 60+ year old residence.

Conducted a comprehensive HVAC replacement estimate for a remodel project with no existing system currently in place. Assessment included evaluation of space requirements for new furnace, air conditioning unit, and complete ductwork installation in a residential interior with ornate trim work and hardwood flooring.