Blind & Sons: Trusted HVAC, Electrical & Plumbing Services in Mogadore, OH

Performed a fire-safety inspection of the garage Reznor unit heater following recent attic insulation work, checking the heater, gas piping and shutoff, flexible vent connection, and galvanized flue/vent pipe for proximity to combustibles. Observed fiberglass batt insulation with torn or sagging kraft facing in the surrounding ceiling cavity and loose, displaced insulation near the vent elbow, and documented all conditions with photos.

Completed scheduled heating maintenance on a 7-year-old Lennox gas furnace system. Performed comprehensive inspection of all components including burner assembly, heat exchanger, ignition system, blower motor, and venting system with white PVC exhaust pipes. Verified proper operation of gas valve, electrical connections, and integrated water treatment device, confirming all equipment is functioning within normal parameters and does not require replacement at this time.

Completed full HVAC system installation including 80% efficiency furnace in basement and air conditioning unit in attic over multiple days. Installed complete new ductwork distribution system throughout attic space and basement areas to ensure proper airflow and system efficiency. Replaced electrical fuses with 30-amp Littelfuse FLNR dual-element time-delay fuses rated for 250 volts to provide appropriate overcurrent protection for the new equipment. All components tested and verified operational upon completion.

Installed gas line routing for attic-mounted gas furnace installation. Ran black iron pipe from exterior meter location through basement ceiling joists to attic furnace position, ensuring proper support brackets and code-compliant installation throughout run.

Installed dedicated electrical circuits for AC and furnace systems. Ran new wiring through attic space and mounted junction box on structural beam to facilitate proper wire routing and connections. Installed gray PVC conduit from junction box to electrical panel for code-compliant wire protection. Made all necessary wire terminations using appropriate wire nuts for red, black, green, and yellow conductors within junction box. Extended circuit wiring to main electrical panel and installed new circuit breakers in available positions on bus bars. Connected all hot, neutral, and ground conductors to their respective terminals and grounding bar within panel. Secured all wiring with proper mounting brackets and ensured conduit was firmly attached to structural members. Verified all connections were tight and properly torqued. Tested circuits for proper voltage and confirmed both AC and furnace systems received adequate dedicated power supply per manufacturer specifications and local electric

Completed estimate for replacement of 40+ year old oil furnace rated at 120,000 BTU with 10/2 electrical service at 230 volts. Unit has reached end of service life with obsolete parts no longer available for repair. Documented existing HVAC system configuration including ductwork connections, water heater proximity, and mechanical room layout for replacement planning.

Responded to no-heat call on oil furnace with pilot light failure. Upon inspection, found flame sensor heavily corroded with significant mineral buildup and oxidation preventing proper flame detection. Removed and cleaned flame sensor assembly, restored proper operation, and verified pilot light ignition and main burner function.

Completed annual maintenance on one-year-old furnace system. Performed standard tune-up procedures, inspected all components for proper operation, and verified system is functioning within manufacturer specifications.

Conducted furnace replacement estimate for Armstrong Air Ultra V unit with reported cracked heat exchanger as identified by previous contractor. Documented existing basement installation including current furnace configuration, ductwork connections, PVC venting system, and surrounding utility equipment including water heater. Noted evidence of previous water damage on concrete floor near equipment area and assessed accessibility for replacement work.

Performed scheduled heating maintenance on a 5-year-old system. Removed and inspected blower wheel assembly, which showed dust and dirt accumulation on blades. Cleaned blower components and verified proper operation before reassembly.

Conducted comprehensive on-site evaluation of existing HVAC system including furnace, air conditioning, and boiler equipment to provide replacement options. Assessed current mechanical room configuration with aging teal-colored boiler featuring mounted expansion tank, red circulation pump, and extensive copper piping showing visible corrosion and wear, along with separate gray furnace unit connected to PVC condensate drainage and metal ductwork, and water heater installation. Documented equipment conditions, measured existing installations, evaluated ductwork and piping infrastructure, and photographed all components to prepare detailed replacement estimate with multiple equipment options for customer consideration.

Responded to a no-start condition on a Generac Guardian 15kW natural gas standby generator that had never been serviced since installation three years prior. Unit displayed a red fault light and failed manual start attempts. Performed comprehensive diagnostic evaluation, identified maintenance-related issues preventing operation, and completed necessary repairs to restore the generator to full operational status.

Completed preventive maintenance on a one-year-old air conditioning system during scheduled morning appointment. Inspected and evaluated the air filter, which showed dust accumulation consistent with normal operation, and performed standard cooling system checks. Verified all components were functioning properly and system operation met manufacturer specifications for continued reliable performance.

Completed comprehensive MVP air conditioning maintenance service including thorough inspection of evaporator coil assembly and control board systems. The evaporator coil showed moderate dust and debris accumulation between the fins, which was cleaned to restore optimal airflow and heat transfer efficiency. Inspected dual-board electronic control system, verified all wire harness connections, terminals, and surface-mounted components were secure and functioning properly to ensure reliable system operation throughout the cooling season.

Completed MVP heating maintenance visit and system inspection. Examined heat exchanger interior, which showed signs of oxidation and mineral deposits with rust-colored accumulation at the base requiring monitoring. Inspected and documented HVAC air filter condition, noting dust accumulation on pleated media indicating normal operation since last service interval.

Responded to service call for reported AC compressor issue. Upon arrival, performed visual inspection of outdoor condensing unit located beneath elevated deck in overgrown area. Unit appeared operational with no immediate signs of compressor failure or refrigerant leakage. Cleared excessive vegetation and debris from around unit perimeter to ensure proper airflow and accessibility for diagnostic testing. Conducted operational assessment including amperage draw, capacitor testing, and system pressures to evaluate compressor performance. All readings within normal operating parameters with no abnormal sounds or vibrations detected. Advised customer that compressor and overall system functioning properly at time of inspection, though age of equipment unknown and vegetation management recommended for continued efficient operation.

Responded to service call for gas odor and flashing red diagnostic light on 3-year-old Lennox ML180UH090E48B furnace. Upon inspection, discovered significant ice and frost buildup on refrigeration line connections and metal piping joints, indicating potential refrigerant leak rather than gas leak. Documented extensive frost accumulation on copper pipe joints, insulated lines, and surrounding components with photographic evidence for warranty claim consideration.

Completed routine heating maintenance on a four-year-old furnace system with no reported issues. Performed comprehensive tune-up including inspection of heat exchanger coils, refrigerant lines, and evaporator components. Documented system condition with photos showing copper refrigerant tubing connections, brass fittings, and insulated line sets in good working order.

Responded to main drain backup in basement utility area. Successfully cleared obstruction from main drain line using professional drain cleaning equipment, restoring proper drainage flow throughout the system. Also replaced faulty shut-off valve under kitchen sink to prevent future leaks and ensure reliable water control.

Completed routine MVP cooling maintenance visit on geothermal HVAC system. Inspected indoor air handler unit, verified proper operation of all components, and documented refrigerant line connections and insulation integrity. All systems functioning within normal parameters at time of service.