Trusted HVAC, Plumbing & Electrical Services in Munroe Falls, OH

Performed annual maintenance on a 5-year-old gas furnace, including inspection of the flame sensor/ignition components and a combustion analysis on natural gas. Readings showed O2 at 10.3%, CO at 20 ppm, CO2 at 6.0%, and 95.6% efficiency, indicating the unit is operating safely and within normal parameters.

Performed MVP maintenance on a Lennox gas furnace, removing the front access panel to inspect internal components including the inducer motor, pressure switch, wiring, flue connection, and gas piping. Conducted electrical diagnostics with a digital clamp meter, recording a 53.1 Ω resistance reading, and found no visible rust, frost, cracks, or damage. Reinstalled the access panel after the inspection.

Repaired separated sections of duct board in the attic by resealing the joints with foil tape and mastic to restore an airtight seal. Installed additional plumbing strap supports along the ductwork to improve load distribution and prevent the sections from separating again.

Performed annual maintenance on a one-year-old natural gas furnace, including inspection of the pleated air filter, which was clean and in serviceable condition with no restriction or damage observed. Conducted a combustion analysis with a Bacharach analyzer, recording O2 at 6.9%, CO at 32 ppm, CO2 at 7.9%, and combustion efficiency of 95.1%, confirming the unit is operating within normal parameters.

Performed an on-site evaluation for a furnace replacement estimate. Inspected the existing galvanized upflow furnace and associated supply/return ductwork located in the utility area, documenting its condition with photographs, including visible residue and corrosion near the lower access panel. Measured the cabinet dimensions and recorded unit data from the nameplate to determine sizing and clearance requirements for the replacement system.

Performed annual tune-up on an 11-year-old Trane gas furnace, including inspection of the burner assembly and flame sensor, with the hot surface igniter found worn and showing chalky residue and discoloration on the element. Verified burner ports and heat exchanger access area were free of heavy rust, cracks, or corrosion, and installed the requested Aprilaire 413 filter and No. 35 water panel to complete the service.

Performed annual maintenance on a 2-year-old gas furnace, including inspection of the draft inducer assembly, gas valve, and internal wiring with the upper access panel removed, and verification of proper operation. Inspected the return air filter and noted dust and debris loading. Completed the previously quoted evaporator coil cleaning to restore proper airflow and heat transfer efficiency.

Assessed a leaking tanked water heater, which was reported to be leaking from the top, and provided a quote for full replacement. Inspected the unit's surrounding installation, including the insulated supply piping with isolation valves and the flexible conduit run, to determine the scope of work required for the changeout.

Performed scheduled electrical maintenance on the standby generator, including load testing of the starting battery with a digital battery analyzer. Results confirmed a healthy battery at 100% state of health and 100% state of charge, measuring 13.77V with 682A CCA against a 540A rating and 4.28 mΩ internal resistance, so no battery replacement was required. The generator is verified ready for reliable starting and operation.

Delivered and replenished water softener salt, loading Morton Professional Water Softener Crystals into the brine tank until filled to an appropriate level. Verified the tank lid, brine well, and surrounding area were in good order, and left remaining bags staged beside the unit for future use.

Replaced the starter on an 8kW standby generator per a prior third-party diagnostic. Removed the failed starter, installed the new OEM Generac unit, and secured the electrical connections at the solenoid. If the unit still fails to run after this repair, further diagnostics will be required to identify the underlying fault.

Performed a tune-up and inspection on a Lennox high-efficiency gas furnace with PVC intake/exhaust venting and condensate drain line. Visually inspected the accessible supply-side galvanized ductwork to evaluate the need for duct cleaning. No frost, rust, cracks, or visible damage found on the equipment, venting, or ductwork, and the unit was left in proper operating condition.

Responded to an active leak at the kitchen ceiling and opened the wall cavity to trace the source to the supply piping serving the tub/shower area. Isolated the water supply, replaced the failed section of copper supply line with a new brass ball valve and fittings, and dried the affected framing and subfloor areas. Confirmed the repair held with no further leaks.

Responded to callback regarding ductwork separation in attic for 1-year-old gas furnace installation. Inspected black flexible ductwork running through attic space and confirmed proper connections and support. Verified all duct joints, secured loose sections with appropriate fasteners, and ensured rigid white duct pipe connections were properly sealed with metallic tape at transition points.

Completed annual maintenance on 3-year-old gas furnace. Performed comprehensive system diagnostics using digital multimeter to verify electrical components and connections operating within specifications. Measured and recorded gas pressure readings using dual-port manometer, confirming inlet pressure at 0.10" and manifold pressure at 0.16" within acceptable range for proper combustion. Inspected condensate drainage system, ductwork, and refrigerant lines for proper installation and secure mounting. All equipment functioning properly with no deficiencies noted.

Completed comprehensive tune-up on 5-year-old Lennox SL280UH090V36B furnace in preparation for heating season. Performed standard maintenance protocol including inspection of blower assembly, evaporator coil, and all system components. Measured and verified gas pressure at 5.930 inH2O using calibrated manometer, confirming proper fuel delivery within manufacturer specifications. Inspected humidifier media pad, refrigerant lines, and all mechanical connections. System operating efficiently with all parameters within normal range and ready for winter operation.

Installed customer-supplied garbage disposal unit under kitchen sink. Completed all necessary mounting and plumbing connections, integrating the disposal with existing PVC drain lines. Secured unit to sink flange and connected discharge piping to drainage system. Tested operation to ensure proper function and verified all connections for leaks.

Responded to clogged first-floor bathroom drain service call. Upon arrival, inspected the bathroom sink which showed visible staining and drainage issues around the basin outlet. Accessed the drain system through the basement utility area where the plumbing infrastructure was exposed. Successfully cleared the blockage in the drainage line using appropriate tools and techniques. Verified proper water flow and drainage operation at the sink fixture before completing the service.

Performed routine maintenance and flush service on Rinnai tankless water heater unit. Completed standard maintenance inspection of all components, verified proper operation of digital controls, and checked plumbing connections including isolation valves and water lines for any signs of leaks or wear.

Completed MVP heating maintenance visit at residential property. Customer purchased and had technician install new air filter from service vehicle. Performed standard heating system inspection of furnace unit located in basement mechanical room. Verified proper operation of HVAC equipment and documented system condition with photos. All components functioning within normal parameters upon completion of filter replacement and routine maintenance check.