Top-Rated Home Services in North Royalton, OH

Inspected the doorbell system, including the chime unit and main electrical panel area, and traced the low-voltage circuit to diagnose the malfunction. Rewired the chime unit's terminal connections, securing the transformer and button wiring to the correct terminals, and tested the circuit to confirm proper chime operation.

Performed heating-season maintenance on an 11-year-old heat pump system, inspecting the outdoor condenser's electrical compartment, including the 60-amp disconnect/breaker, high- and low-voltage wiring and connections, run capacitors, contactor, and control board. All components were found in good condition with no evidence of frost, rust, corrosion, or burn marks, and the unit is operating properly.

Installed new 90% AFUE furnace with new venting/flue piping. Performed startup and verified operation, measuring a 53.8°F temperature reading at the duct/plenum and 1.76 inWC static pressure with a dual-port manometer to confirm proper system airflow and performance.

Updated the electrical service panel to accommodate a portable generator connection, reorganizing and securing the interior wiring and verifying breaker labeling for the A/C, range, office, garage, and barn circuits. Supplied color-coded conductors (white, red, black, green) for the panel modifications, with cable terminations made through proper connectors at the OSB-mounted enclosure on the CMU wall.

Performed annual preventive maintenance on the furnace, inspecting the evaporator coil, refrigerant lines, and copper fittings, and noting frost accumulation on the coil U-bends, surface oxidation on the copper tubing, and moderate rust on a mounting bracket. Inspected the blower wheel and found the blades intact and free of rust or damage, with only a light dust coating. Unit was left operational, with the rusted bracket and coil frosting recommended for further evaluation.

Arrived to find the system non-operational. Diagnostics determined the pressure switch was failing to open, preventing proper furnace operation, and the switch was corrected to restore operation. Replacement of the pressure switch is recommended to prevent an untimely failure, and corrosion was noted on the gas manifold and shelf beneath the inducer motor.

Installed a new gas supply line to the kitchen range, tapping into the main trunk line located directly below and running rigid black iron pipe to the appliance location per the customer's request for hard pipe. Connections were threaded and sealed with gas-rated pipe dope, followed by a pressure test and leak check to verify a safe, code-compliant installation.

Performed a complete furnace tune-up, inspecting the burner compartment, inducer motor assembly, gas valve, pressure switch, control board, and wiring harnesses. Observed surface rust and debris buildup on the burner tubes and compartment floor, which was noted for monitoring and cleaned as part of the service. All other components were in typical condition with no signs of breakage or ice, and the system was verified for proper operation.

Responded to a no-heat call on a Lennox gas furnace, approximately one year old, after the system was switched over to heating mode. Inspected the furnace and surrounding components, including the gas piping, PVC vent and condensate lines, electrical connections, and supply plenum, and found no visible damage, corrosion, or ice formation. Performed diagnostics on the heating sequence to verify operation, and the unit is now running and producing heat.

Diagnosed an inoperative exterior lamp post fixture that did not respond to a bulb replacement, testing the circuit and fixture components to isolate the fault. Replaced the lantern-style lamp top with the customer-supplied unit, secured the new head to the post, and restored power. Verified proper operation of the fixture.

Performed annual maintenance on a 22-year-old gas furnace, inspecting the heat exchanger section, gas valve assembly, wiring, and gas piping, with no visible rust, breakage, or damage noted in the furnace cabinet. Filter had already been replaced by the customer. Inspected the evaporator coil cabinet and observed surface corrosion and rust spotting on the coil edge and cabinet base, along with mineral residue on the cabinet wall, and recommend monitoring or further evaluation of the coil.

Completed MVP furnace maintenance service including full system inspection and air filter replacement. Removed heavily soiled pleated air filter showing significant dust and particle accumulation, installed new filter with proper seating in mounting frame, and verified all refrigerant lines and connections were secure with no visible leaks or damage.

Responded to outdoor porch light fixture with damaged wiring caused by animal activity. Upon inspection, found wires had been chewed through, rendering the fixture inoperable. Rewired the affected circuit with new conductors, ensuring proper connections and code compliance. Inspected electrical panel and meter installation to verify circuit integrity and proper grounding. Documented existing conditions and completed repairs to restore safe operation of the outdoor lighting fixture.

Completed scheduled maintenance visit for MVP customer's Lennox HVAC system. Performed standard cooling season inspection, verified furnace unit operation, and confirmed electrical disconnect box components were functioning properly with all three fuses intact and secure.

Completed MVP heating maintenance service on schedule. Performed comprehensive system inspection including blower assembly examination and condensate drain verification. All components found operating within normal parameters with blower wheel showing proper rotation and drainage system functioning correctly.

Responded to service call for toilet leaking at base. Upon inspection, identified failed wax ring and mounting hardware causing water seepage. Documented existing conditions with photos showing toilet tank components and fill valve assembly. Ordered replacement parts for return visit to complete repairs, including new wax ring and mounting bolts to properly reseal toilet base and eliminate leak.

Replaced three customer-supplied smoke detectors in bedroom locations. All units were successfully installed and tested for proper operation, with indicator lights confirming functionality upon completion.

Conducted assessment of exterior plumbing system to provide estimate for replacement of pressure reducing valve and outdoor hose bib. Inspected existing outdoor spigot mounted on building exterior and performed water pressure testing using calibrated gauge to evaluate system performance. Documentation included pressure readings and current condition of outdoor faucet assembly and associated fixtures.

Responded to gas leak emergency on 5-year-old furnace where Columbia Gas had already shut down system for safety. Performed diagnostic testing using digital manometer to measure gas pressure at valve assembly, confirming burner bleeding issue. Inspected gas valve, control wiring connections, and copper supply line for potential failure points. Documented equipment condition with photos showing gas valve assembly, pressure readings, and wire connections to terminals. Furnace remains offline pending further repairs to address gas valve or control box malfunction causing the leak condition.

Replaced malfunctioning Moen tub shower faucet with new Moen Chateau valve assembly. Cut and installed new access panel for valve access, and installed two shut-off valves for isolation purposes to facilitate future maintenance and repairs.