Trusted HVAC, Plumbing & Electrical Services in Peninsula, OH

Completed installation of 10KW standby generator with 16-circuit transfer switch at residential property. Ran 15 feet of gas line from existing service to generator location and installed 20 feet of electrical conduit along exterior foundation to connect unit to main electrical panel. Mounted generator on concrete pad, staged and connected transfer switch in attic space with proper wire terminations, installed oil heater and battery, and tested all connections for proper operation and automatic transfer functionality.

Completed MVP cooling maintenance visit on 9-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condensing unit, accessing internal electrical components and control board to verify proper operation. Inspected wiring connections, capacitor, and control circuitry for signs of wear or failure. All electrical connections found secure and system operating within normal parameters for unit age.

Removed existing toilet and installed new American Standard Champion right height elongated toilet with slow close seat. Replaced existing angle stop with new straight stop valve and connected supply line. Tested flush operation and checked all connections for leaks to ensure proper functionality.

Completed MVP cooling maintenance visit on a 2-year-old system. Accessed outdoor condenser unit, inspected electrical components including capacitor and wiring connections, and documented equipment condition with photos showing unit exterior with visible dirt accumulation and interior electrical compartment with all connections intact.

Responded to customer complaint of toilet leaking at the connection point between tank and bowl. Upon inspection, identified poor seal integrity likely caused by inferior quality tank-to-bowl gasket and mounting hardware. Documented existing conditions with photographs given customer's concerns about protecting recently remodeled bathroom in historic home. Assessed fixture components and provided recommendations for proper repair to prevent water damage to surrounding floor and wall surfaces.

Completed follow-up service call to repair leaking washing machine water supply line. Replaced faulty shut-off valve and supply connection, tested both hot and cold water lines for proper operation and confirmed leak was fully resolved with no further dripping or moisture present.

Completed annual maintenance visit on 1-year-old Lennox air conditioning condenser unit. Performed comprehensive system inspection, verified proper refrigerant levels via copper line connections, confirmed condenser fan operation, and checked electrical components. Unit operating within normal parameters with no issues identified.

Completed MVP cooling maintenance visit on 7-year-old Lennox system that had been rescheduled from previous appointment. Upon inspection, found outdoor condensing unit coils heavily contaminated with dirt, dust, and debris buildup significantly restricting airflow through aluminum fins. Performed thorough coil cleaning to restore proper heat transfer efficiency and system performance. Documented equipment condition with photos of indoor furnace unit and outdoor condenser before service completion.

Completed preventive maintenance visit on residential air conditioning system. Performed thorough inspection of outdoor condenser unit, which exhibited heavy accumulation of dirt, debris, and organic matter on exterior coil surfaces that was significantly restricting airflow and reducing system efficiency. Removed access panels to inspect internal electrical components, including capacitor, contactor, and wiring connections. All electrical connections were found to be secure with no signs of overheating or deterioration. Unit operational at time of inspection.

Conducted on-site electrical assessment for backup generator installation at residential property. Customer requires uninterrupted power due to medical oxygen equipment dependency. Performed comprehensive evaluation of existing electrical infrastructure and identified optimal generator placement location. Documented current electrical service capacity, main panel specifications, and available space for transfer switch installation. Photographed basement area showing exposed floor joists, concrete block foundation walls, and existing HVAC ductwork to assess potential routing paths for generator feed lines and natural gas supply. Noted unfinished basement conditions including deteriorated insulation and structural elements that may require consideration during installation planning. Provided customer with financing options information as requested to facilitate project approval and scheduling.

Responded to service call for 28-year-old furnace system requiring diagnostic evaluation. Upon inspection, determined that the furnace bonnet requires replacement due to age-related deterioration. Documented existing equipment condition with photographs showing rooftop-mounted venting system and associated infrastructure. Provided diagnostic findings and replacement recommendations to customer, with availability confirmed for installation scheduling.

Completed comprehensive air conditioning tune-up on residential condensing unit, including inspection of exterior components, electrical connections, and control board functionality. Verified proper operation of capacitors, relay systems, and circuit board, with all wiring connections secure and system operating within normal parameters.

Completed comprehensive MVP maintenance on furnace and air conditioning system. Performed thorough inspection of heating components including burner assembly, ignition chamber, gas valve, blower motor, and all electrical connections. Verified proper flame operation with visible blue flame indicators and tested system controls for safe operation. Measured and recorded temperature differential readings at 12.18°F to confirm adequate heat exchange performance. All components found operating within manufacturer specifications with proper wire management and secure mounting throughout the unit.

Completed scheduled preventive maintenance on 2-year-old residential air conditioning system. Performed comprehensive cooling season inspection of outdoor condenser unit, including visual assessment of cabinet condition, refrigerant line connections with service ports, and proper drainage system operation. Verified unit placement on concrete pad with adequate clearance, confirmed landscape mulch maintained appropriate distance from unit for proper airflow, and documented system condition through photographic records for maintenance history.

Responded to service call for clogged bathtub drain in 14-year-old residential property. Upon arrival, assessed the bathroom plumbing system and identified blockage in the bathtub drainage line. Successfully cleared the obstruction using appropriate drain cleaning equipment, restoring proper water flow and drainage function. Tested the system to verify complete resolution, and all fixtures were left in clean, operational condition.

Completed installation of 20kW Kohler standby generator with 200-amp automatic transfer switch at residential property. Ran 30 feet of gas and electrical supply lines from house to generator pad, mounted unit on concrete pad with proper conduit connections to existing electrical system. Generator and all components were sourced from Buckeye Power Sales and system was installed per manufacturer specifications without requiring utility disconnect.

Conducted furnace replacement estimate for mobile home HVAC system. Assessed existing older furnace unit housed in wall-mounted utility compartment, documented equipment condition showing age-related wear, dust accumulation, and identified ceiling access panel requiring opening for complete system evaluation. Provided replacement recommendations based on current equipment configuration and mobile home installation requirements.

Completed comprehensive A/C tune-up service on residential cooling system. Inspected outdoor condensing unit with operational fan assembly and verified proper electrical connections at disconnect box. Examined indoor evaporator coil assembly, noting mineral deposits and discoloration on humidifier pad requiring future attention, and confirmed drainage system functionality with visible PVC piping connections in proper working order.

Responded to service call for 13-year-old residential gas boiler displaying error code 57. Upon arrival, performed diagnostic assessment of the heating system and identified the fault condition. Inspected boiler components, electrical connections, and control panel to determine root cause of error code. Documented equipment condition with photographs showing boiler unit, pressure gauge readings, copper piping connections, electrical panel, and associated mechanical components. Communicated diagnostic findings to appropriate contacts for determination of repair or replacement recommendations.

Responded to no-heat call on 9-year-old propane furnace. Upon arrival, found unit non-operational after homeowner attempted multiple restart cycles. Performed diagnostic inspection of blower assembly and burner components. Inspected humidifier drum and filter condition within cabinet. Identified moisture accumulation on blower housing and checked all electrical connections to motor and control board. Verified propane supply was adequate and examined ignition sequence operation. Documented equipment condition with photographs showing interior components including blower assembly, humidifier unit, and filter installation.