Your Local Richfield Home Services Contractor Since 1937

Responded to service call for clogged kitchen drain in residence with 12-year-old plumbing system. Upon inspection, confirmed blockage in kitchen sink drain line beneath cabinet. Successfully cleared obstruction using drain snake through P-trap assembly and drain line. Verified proper drainage flow and tested system to ensure complete clearance of blockage.

Responded to plumbing service call for multiple leak issues throughout the property. Diagnosed and identified three separate faucet leaks requiring repair, a refrigerator water supply line leak, and several deteriorated shut-off valves in need of replacement. Accessed crawl space area to inspect copper supply lines and existing valve installations. Documented conditions of exposed plumbing infrastructure including pipe routing and mounting hardware for valve replacement planning.

Completed comprehensive duct cleaning service for residential HVAC system consisting of 14 vents. Removed accumulated dust, debris, and particulate matter from ductwork and ventilation openings throughout the property. All vent registers and duct interiors were thoroughly cleaned and inspected, with visible improvements to air pathway cleanliness and system accessibility confirmed through documentation photography.

Completed MVP AC maintenance on cooling system. Performed comprehensive inspection of electrical control panel, verifying all wire connections, terminals, and safety switches for proper operation. Inspected evaporator coil, refrigerant lines, service valves, and accumulator, confirming system components are functioning within normal parameters and unit is operating efficiently.

Completed preventive maintenance inspection on Lennox condensing unit for MVP customer. Performed electrical diagnostics using clamp meter, measuring amperage at 0.55A and voltage at 126.5V to verify proper compressor operation and system performance. All measurements within manufacturer specifications, unit operating normally with no deficiencies noted.

Responded to service call regarding exposed electrical wiring emerging from underground conduit installation completed during previous work. Inspected underground access shaft containing electrical conduit and monitoring equipment, verified proper installation and functionality of existing infrastructure, and documented current conditions with photographs for service records.

Replaced aging duplex outlets throughout a 25-year-old residential property to ensure safe and reliable electrical operation. Work was performed in the kitchen area and basement utility space, addressing worn receptacles that had reached the end of their service life. All replaced outlets were tested for proper grounding and polarity upon installation.

Completed installation of 22kW standby generator system with cold weather kit and whole home surge protection. Installed 200-amp automatic transfer switch with new electrical panel, ran 60 feet of electrical line from main service to transfer switch location, and coordinated with gas utility contractor for 10-foot gas line connection. Configured transfer switch to eliminate disconnect requirement per engineering specifications, performed complete system commissioning and testing to verify proper automatic transfer operation and generator functionality under load conditions.

Responded to service call regarding newly installed air conditioning unit with reported damage to rear cabinet panel allowing excessive air leakage. Upon inspection, confirmed cabinet damage at back of outdoor unit with noticeable air escape from compromised section. Documented damage with photographs showing affected area and PVC refrigerant line routing for warranty claim processing and potential cabinet panel replacement.

Completed a two-day HVAC installation involving the removal of an existing air conditioning system and installation of a new Lennox unit with coil replacement. The first day consisted of disconnecting and removing the old outdoor condensing unit, while the second day involved setting the new Lennox air conditioner on a protective rubber pad, installing the matching evaporator coil, and relocating the humidifier to optimize system performance. All refrigerant lines were properly connected and insulated, electrical disconnects were installed per code requirements, and condensate drainage was routed through PVC piping. The system was charged to manufacturer specifications, tested for proper operation, and verified for adequate airflow and temperature differential across the coil.

Replaced faulty fuse holder inside outdoor AC disconnect switch. New fuse block installed with proper fuses to restore safe electrical operation to the condensing unit.

Completed standard AC tune-up on Lennox system with AirBoss zoning control. System operational and customer renewed maintenance plan during visit.

Performed diagnostic inspection of outdoor A/C condenser unit. Found unit installed directly on wooden deck without proper equipment pad, causing unit to lean and creating potential for long-term structural damage and reduced system efficiency. Documented existing installation conditions with photos showing improper mounting configuration and lack of level foundation. Advised customer that unit requires proper concrete or composite equipment pad and leveling to ensure optimal operation, prevent vibration damage, and maintain manufacturer warranty compliance.

Responded to service call for outdoor sump pump receptacle replacement in 37-year-old residence. Upon arrival, inspected existing electrical outlet serving sump pump system and found heavily corroded receptacle and deteriorated wiring connections due to age and environmental exposure. Verified electrical panel configuration and circuit integrity using digital multimeter to ensure proper voltage and grounding before proceeding with replacement work. Disconnected power at breaker panel, removed failed receptacle, and installed new weather-resistant GFCI outlet suitable for outdoor/damp location applications. Tested new installation for proper operation, ground fault protection functionality, and verified secure mounting. Restored power and confirmed sump pump operational status with new receptacle.

Completed Early Bird A/C Tune-Up on residential cooling system per customer request. Performed comprehensive inspection of outdoor condensing unit, noting significant dust and debris accumulation on condenser coils with visible brownish-gray discoloration affecting heat transfer efficiency. Inspected indoor air filter, which showed moderate dust loading but remained serviceable. Documented unit condition with photographs showing horizontal fin coils requiring attention and filter assembly with proper installation. System operational at time of service with fan assembly functioning normally.

Responded to service call for non-operational sump pump system. Upon inspection, found existing pump in basin with significant mineral deposits, rust-colored staining, and corrosion throughout the pit. Standing water present indicated pump failure. Documented condition with photos showing deteriorated basin with concentric ring staining and compromised discharge piping. Coordinated with technical team for pump replacement evaluation and scheduling.

Completed installation of 90% AFUE furnace and air conditioning system. Installed new outdoor condensing unit on concrete pad with proper clearances, ran refrigerant lines and electrical connections through exterior wall. Replaced indoor air handler and evaporator coil assembly, installed new electrical disconnect with fuses, and connected condensate drainage line. System was pressure tested, evacuated, charged to manufacturer specifications, and tested for proper operation. All components functioning within normal parameters upon completion.

Responded to no heat call on five-year-old furnace with no airflow. Upon inspection, found unit completely non-operational with gas valve assembly and control board accessible for diagnostics. Verified proper venting configuration with PVC intake and exhaust pipes, checked all electrical connections at gas valve terminals, and inspected pressure switch and safety circuits. All wiring harnesses, including thermostat wiring and limit switch connections, were examined for continuity and proper seating. Unit components appeared clean and well-maintained with no visible signs of wear or damage to internal mechanisms.

Completed routine maintenance on 3-year-old Lennox air conditioning system. Performed standard tune-up procedures including inspection of condenser unit, verification of electrical connections, and system operational check. Unit found to be functioning properly with no issues identified.

Completed comprehensive MVP furnace and air conditioning maintenance inspection per scheduled appointment. System evaluation revealed normal operational conditions with refrigerant lines showing appropriate condensation patterns and proper insulation installation on copper piping. Heat exchanger fins displayed clean condition with no visible debris accumulation, and all ductwork connections remained secure with no air leakage detected.