HVAC, Plumbing & Electrical Experts Serving Seville, OH

Removed and replaced the existing water heater with a new 40-gallon tall Bradford White unit, installing new water and gas shut-off valves and reconnecting the vent connector. Added strapping to properly support the gas and water supply lines, and installed a thermal expansion tank on the cold water line to protect against pressure buildup. The system was verified free of leaks, and the new tank carries a 6-year warranty.

Performed an on-site assessment for a new exterior outlet installation, including inspection of the main breaker panel, existing branch circuit wiring, and available panel capacity. Evaluated cable routing options from the panel and surrounding joist area to the exterior wall location, and noted loose conductors and unsecured wiring near the panel that should be addressed during installation. Provided an estimate for the proposed outlet installation work.

Responded to no hot water complaint at residential property. Upon inspection, found existing tanked water heater had failed and required complete replacement. Assessed existing plumbing infrastructure including aged copper supply lines, shutoff valves, and connections showing significant corrosion and deterioration. Removed old water heater unit and installed new tanked water heater with proper venting and code-compliant connections. Tested all hot water fixtures to confirm proper operation and adequate water temperature throughout the home.

Replaced existing AO Smith 50-gallon electric water heater with new Bradford White 50-gallon electric unit including 6-year manufacturer warranty. Installation included new ball valve, proper bonding wire, and thermal expansion tank. Repaired leaking hot water side piping and replaced corroded shut-off valve on hot water line. Removed and capped corroded shut-off valve located in ceiling near laundry tub. Replaced corroded straight stops under kitchen sink and eliminated unused saddle valve previously connected to ice maker.

Responded to service call for leaking pipes in utility area. Upon inspection, identified deteriorated horizontal PVC pipe with visible staining and corrosion on metal fittings. Assessed vertical plumbing assembly and overhead pipe runs in basement area, noting aged infrastructure with rust accumulation on support column and compromised insulation wrapping on sections of piping. Documented conditions of all affected plumbing components and provided recommendations for necessary repairs to address active leaks and prevent future failures in the aging system.

Completed MVP heating maintenance visit on residential HVAC system. Performed comprehensive system inspection of outdoor condenser unit and internal electrical components. Utilized digital multimeter to verify proper electrical readings, measuring 50.9 volts at capacitor terminals to ensure system operating within manufacturer specifications. Inspected all electrical connections, wiring harnesses, and control board components for signs of wear or damage. All components functioning properly with no issues identified during diagnostic testing.

Responded to no cooling call and inspected thermostat at 120 service call location. Found significant corrosion on thermostat wiring terminals and connections, indicating moisture intrusion or age-related deterioration. Documented existing wiring configuration with multiple low-voltage connections (R, Y, G, B, O, C) before removal, noting rust-colored oxidation on wire bundle and terminal block that was preventing proper electrical contact and system communication.

# HVAC Service - A/C Responded to service call for 9-year-old air conditioning unit operating with abnormal noise. Upon inspection of outdoor condenser unit, identified failed capacitor as source of operational issue. Removed access panel and performed electrical component diagnostics. Replaced defective dual-run capacitor with new MARS replacement unit. Verified all electrical connections were secure and properly terminated. Cleaned accumulated debris from electrical compartment and components. Tested system operation following repair—unit now running quietly with normal sound levels and proper electrical readings. System returned to full operational status.

Completed comprehensive plumbing repairs addressing multiple fixtures and water hammer issues throughout the residence. Installed new flanged tailpiece on laundry room sink to restore proper drainage. Pulled and reset hall bathroom toilet to ensure proper seal and eliminate leaks. Replaced hall bathroom shower valve to resolve water hammer condition. Installed new double check valve to eliminate water hammer occurring when toilets are flushed. Removed and replaced master bathroom toilet with new elongated comfort height model for improved functionality and comfort. Removed obsolete booster pump system that was no longer required for the property's water pressure needs. Retained existing ball valves in bypass configuration for potential future water softener installation and capped all 3/4-inch supply lines to prevent leaks. Installed wall access panel with copper supply piping, brass fittings, and green-handled shut-off valves for easy maintenance access. All work completed to code wit

Replaced exterior electrical disconnect on HVAC system and sealed penetration around new disconnect box per inspector's requirements. Documentation photos were captured and submitted to building inspector for final approval and inspection sign-off.

Completed scheduled MVP heating maintenance visit. Performed system inspection and diagnostics on heating equipment. Accessed internal components through equipment panel, examining flame sensor assembly and removing component for cleaning. Tested sensor probe insertion and proper seating within burner assembly access port. Inspected blower housing and associated mechanical components for proper operation. Verified all connections secure and system operating within normal parameters. Equipment returned to full operational status following maintenance procedures.

Responded to no cooling complaint on 9-year-old central air conditioning system. Upon arrival, confirmed outside condenser unit fan was operational but no cool air was being delivered through supply vents. System was shut down to prevent further complications. Conducted diagnostic inspection and identified failed blower wheel as root cause of airflow failure. Accessed indoor air handler unit located in basement, removed defective blower wheel assembly, and installed replacement component. Verified proper operation of blower motor and wheel rotation. System restored to full functionality with adequate airflow through all supply registers and normal cooling operation confirmed.

Completed geothermal system estimate for 16-year-old unit requiring ECM motor replacement. Provided quote for 2300 ECM motor installation, documented existing equipment condition with photos, and presented maintenance value plan options to customer.

Responded to no-heat call on 15-year-old geothermal heat pump system displaying low pressure error code and complete failure to operate. Upon inspection, identified dirty filter restricting airflow and verified blower motor assembly operation. Cleared error code, replaced air filter, and restored system to normal heating operation.

Performed scheduled maintenance on a 7-year-old residential generator unit. Upon inspection, noted the status indicator displayed half green and half orange, suggesting a potential service alert or transitional operating condition. Documented equipment condition with photographs for service records.

Responded to multiple plumbing concerns at a 31-year-old residential property. Addressed high water pressure issue causing loud squealing noise in pipes by adjusting pressure regulator to manufacturer specifications. Replaced deteriorated drain trap assembly under utility sink with new P-trap and tailpiece components, ensuring proper seal and drainage. Performed mechanical snaking of bathtub drain to remove hair and debris buildup, restoring proper water flow. All fixtures tested and confirmed operational upon completion.

Replaced existing sewage pit and sewage pump with new units, connecting new pump to existing discharge line and vent system. Modified lavatory drain configuration for basement bathroom by connecting to sewage pit vent rather than direct pit lid connection, requiring access through drywall and tile in basement bathroom area. Jackhammered concrete near existing sewage pit location to install new storm water crock and connected existing perforated pipe to new discharge line running to existing downspout. Installed new 1/3 HP sump pump in new sump crock with new check valve. Tested all connections and discharge systems to verify proper operation and absence of leaks. Repoured concrete to rough finish over excavated areas. Exterior drainage system now includes visible turquoise PVC piping running through foundation planting bed, connecting to white downspout along house siding for proper storm water management.

Completed annual MVP cooling maintenance visit on 1-year-old HVAC system. Removed access panels to inspect control board, electrical connections, and blower motor assembly. Verified all wiring connections secure with proper color-coded routing throughout control section. Inspected transformer, circuit boards, and motor components for proper operation and wear patterns. All components functioning within normal parameters with minimal dust accumulation consistent with system age.

Completed routine maintenance visit for MVP customer's cooling system. Inspected indoor Lennox furnace unit in basement and outdoor condensing unit, verifying proper installation, venting configuration, and refrigerant line connections. Both units operating within normal parameters with no visible damage or service issues identified at time of inspection.

Completed MVP recurring cooling maintenance visit on 4-year-old Lennox system. Performed standard preventive maintenance inspection of air handler and furnace unit, verified proper operation of all components, checked refrigerant levels, inspected ductwork connections, and confirmed system is operating within manufacturer specifications.