Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Upgraded 21 two-prong outlets to GFCI receptacles throughout multiple floors of the residence, excluding the refrigerator outlet. Installed wire mold extension boxes on outlet boxes with insufficient depth to accommodate GFCI devices. Two-person crew completed the electrical safety upgrade in approximately six hours.

Provided estimate for complete air conditioning system replacement after diagnosing failed compressor on 21-year-old unit with no cooling capability. Documented existing outdoor condenser unit and indoor Trane XR80 furnace installation in utility closet for replacement planning and equipment sizing specifications.

Completed preventative maintenance cooling visit on two HVAC units. Inspected air handler with heavily clogged filter showing significant dust and debris accumulation, restricting airflow. Inspected attic-mounted equipment and verified proper installation of insulation materials around ductwork and air handling components.

Responded to service call for leaking outdoor spigot. Upon arrival, inspected exterior hose bib mounted on brick wall and identified active leak at valve assembly. Performed pressure test using calibrated gauge to assess system integrity and pinpoint source of water loss. Traced supply lines through interior wall framing where copper piping was routed with insulated protection. Evaluated pipe insulation condition and secured loose sections with additional strapping to prevent future damage from temperature fluctuations. Repaired valve assembly and verified proper operation with blue-handled shutoff functioning correctly. Confirmed no additional leaks present at connections and restored full water flow to outdoor spigot. System tested and operating within normal parameters upon completion.

Responded to service call for non-functional basement light switch and multiple light fixtures missing pull chains. Inspected electrical panel and basement wiring system to diagnose switch malfunction. Replaced defective basement light switch and restored proper operation. Installed pull chain assemblies on fixtures that were missing functional controls, ensuring all lighting fixtures were fully operational upon completion.

Completed MVP recurring maintenance visit on 8-year-old GE outdoor condensing unit. Performed comprehensive system inspection, verified operational parameters, and documented temperature readings of 57°F and 103°F during performance testing. Unit operating within normal specifications with no issues identified.

Responded to no cooling complaint on 20-year-old air conditioning system. Found outdoor condenser unit attempting to start but failing to run, with fan motor running excessively hot. Upon inspection, identified failed condenser fan motor and heavily corroded top grill assembly with significant rust damage affecting unit operation. Diagnosed electrical issue preventing compressor from engaging properly while fan motor was overheating due to mechanical failure.

Completed estimate for ductless mini-split system replacement at residential property. Assessed existing outdoor condenser unit and indoor wall-mounted air handler to determine equipment specifications and installation requirements for one to two new mini-split systems pending customer confirmation.

Completed preventive maintenance cooling visit on 6-year-old HVAC system. Performed system diagnostics using digital measuring instruments, inspected electrical components including capacitor and contactor, verified all wire connections secure, and documented equipment condition with photos. Unit operating within normal parameters upon completion of maintenance.

Replaced undersized electrical box with larger capacity junction box to accommodate GFCI outlet installation on outdoor covered deck area. Upgraded outlet protection to meet current code requirements for exterior receptacle location.

Completed preventive maintenance cooling visit on 2-year-old residential air conditioning system. Performed standard inspection of outdoor condenser unit, noting dusty coil fins consistent with normal outdoor operation. Unit found in functional condition with all components operating as designed.

Responded to no cooling complaint on one-year-old air conditioning system with indoor temperature at 80 degrees. Upon inspection, discovered severe thermal damage and melted insulation at wire connections in the electrical junction area, with visible charring, corrosion, and debris buildup indicating an electrical fault or overheating event. Documented damaged connections with photographs showing compromised wire insulation and corroded terminal blocks requiring immediate repair to restore proper system operation and prevent potential safety hazards.

Responded to cooling system operating below specifications. Diagnosed refrigerant charge deficiency due to system leak. Utilized electronic charging scale to measure and verify refrigerant levels, confirming undercharge condition affecting system performance.

Provided electrical estimate for fixture installation work in attic storage space and stairwell area. Assessment included evaluation of existing exposed conduit runs, flexible conduit routing, and structural mounting requirements for proper fixture placement in accordance with code requirements. Quote encompasses installation specifications for adequate lighting coverage in upper-level access areas with consideration for existing cabinet ventilation systems and structural beam clearances.

Completed 100-amp electrical service upgrade including installation of new main breaker panel with proper circuit protection, necessary grounding system updates to meet current code requirements, and installation of exterior disconnect as mandated by 2023 National Electrical Code. Upgraded interior panel wiring with appropriate conductor sizing and proper terminations to all branch circuit breakers. Additionally identified future work requirements including conversion of pull cord light fixture to standard switch control at stairway location and correction of improper wiring on basement shop light fixture.

# HVAC Maintenance - Cooling Completed scheduled MVP cooling maintenance visit on 1-year-old Lennox condensing unit. Removed access panel and inspected internal electrical components including dual capacitors, contactors, and associated wiring connections. All electrical connections were verified secure with proper wire routing observed throughout the system. Capacitors showed no signs of bulging or leakage, indicating proper operation within expected parameters for equipment age. Examined outdoor unit positioned on concrete pad with noted vegetation encroachment around base and sides of condenser. Exterior coil grille and top fan guard inspected and found intact with no physical damage. Unit maintained adequate clearance from structure despite surrounding landscaping requiring monitoring for future airflow considerations. System operational and functioning as designed. All components within normal operating specifications for routine preventive maintenance service.

Responded to a clogged toilet in the basement that was causing backup into the shower drain. Upon inspection, identified a blockage in the main drain line affecting multiple fixtures. Utilized drain snake equipment to clear the obstruction in the drainage system, restoring proper flow to both the toilet and shower. Verified all fixtures were draining correctly upon completion and advised on proper drain maintenance to prevent future clogs.

Responded to water leak reported beneath newly installed Lennox furnace system. Upon inspection, discovered condensate drain line issue related to the Asurity control board installation and associated drainage components. Verified proper connection of condensate drainage system, checked drain line routing, and ensured all connections were secure to prevent further water accumulation beneath the unit.

Completed scheduled cooling maintenance visit on 6-year-old air conditioning system. Inspected and removed air filters for evaluation, which showed accumulated dust and debris consistent with normal operation. Performed system diagnostics using digital testing meter to verify proper operating parameters and equipment performance. All components inspected and system confirmed to be functioning within normal specifications.

Completed scheduled MVP cooling maintenance visit between 8:00-8:30am as rescheduled. Performed comprehensive system inspection including examination of interior air handler components and control board assembly. Inspected circuit board with relays, capacitors, and electrical connections, verifying all wiring terminations and component functionality. Evaluated cylindrical capacitor and associated electrical components for proper operation. Documented system condition with interior ceiling register location and control board assembly photos showing existing dust accumulation on equipment surfaces. System operating within normal parameters at time of service completion.