Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Responded to service call for storm-damaged electrical service line that had pulled loose from mounting brackets on exterior of residence. Upon arrival, inspected the service entrance conductors and confirmed the weatherhead and service drop connection point had separated from the building-mounted bracket system. Reinstalled and properly secured the electrical service line into the exterior mounting brackets, ensuring proper clearance heights and strain relief per NEC requirements. Verified secure attachment of all hardware and confirmed the service entrance cable was properly supported to prevent future displacement during inclement weather.

Completed MVP cooling maintenance visit on residential HVAC system. Accessed air handler unit in attic space, removed access panel, and performed comprehensive inspection of internal components including blower motor assembly, control board, and electrical connections. Verified proper operation of squirrel cage blower wheel and centrifugal fan assembly. Inspected all wiring connections, refrigerant lines, and system controls. Delivered furnace filter as requested by customer. All components found to be in satisfactory operating condition with normal dust accumulation. System operating within manufacturer specifications.

Responded to no-cooling call where outdoor unit was completely inoperative with no fan operation. Upon arrival, found outdoor condensing unit with electrical disconnect in place but system unresponsive. Diagnosed and resolved power supply issue, restoring full system operation with condenser fan and compressor running properly.

Performed comprehensive cooling system tune-up on 7-year-old air conditioning unit. Upon inspection, discovered heavily soiled condenser coil with significant dirt and debris accumulation restricting airflow, which was cleaned to restore proper heat transfer efficiency. Conducted electrical diagnostics using digital multimeter, identifying frost buildup on refrigeration components indicating potential airflow restriction or refrigerant-related issues. Verified electrical connections, measured system voltages, and ensured all wiring terminals were secure and properly functioning.

Responded to no-cool call on 30-year-old outdoor condensing unit with non-operational fan motor. Upon arrival, found compressor and condenser coils heavily soiled with dirt and debris accumulation affecting heat transfer efficiency. Performed thorough coil cleaning using foaming coil cleaner to remove years of built-up contamination from condenser fins and surrounding components. Due to advanced age of equipment and extent of wear observed on compressor and refrigerant lines, recommended system replacement as most cost-effective long-term solution.

Completed installation of 80% efficiency furnace and air conditioning system. Performed system startup, verified proper refrigerant pressures and temperatures using digital manifold gauges, and confirmed operational parameters met manufacturer specifications. All equipment tested and left in full working order.

Completed routine maintenance on a 3-year-old outdoor air conditioning unit. Inspected and documented heavily soiled air filter requiring replacement due to significant dust and debris accumulation. Examined electrical components, capacitor, and wiring connections inside control panel, confirming all components operating within normal parameters with no visible corrosion or damage detected.

Responded to service call for continuously running shower head. Upon inspection, identified faulty shut-off valve requiring replacement. Repaired shower control mechanism to restore proper water flow operation and eliminate constant running condition.

Performed preventive maintenance on 9-year-old air conditioning system, completing load match verification on both indoor and outdoor units to confirm proper refrigerant charge and system operation. Inspected electrical components including capacitor and wiring connections, measured system performance parameters using digital testing equipment, and verified proper airflow through ductwork in attic installation.

Completed scheduled cooling system maintenance on 9-year-old unit. Inspected condenser fan assembly, verified proper operation of fan motor and blade, and examined internal components. Noted moderate corrosion on ductwork and housing elements, consistent with equipment age and environmental exposure, but all mechanical components functioning within normal parameters.

Responded to callback for improperly buried ground wire at exterior electrical service installation. Previous technicians had installed ground wire below grade, but wire had since become exposed above ground level. Properly buried ground wire according to NEC requirements to protect conductor from physical damage and ensure code compliance. Verified all exterior electrical connections at meter panel and associated conduit runs remained secure and weatherproof upon completion of burial work.

Completed MVP recurring cooling maintenance visit. Performed comprehensive system inspection including internal furnace cabinet components, blower motor assembly, gas valve controls, electrical connections, and control board operation. Verified proper wiring connections throughout system, inspected pleated air filter condition and housing assembly, and confirmed all mechanical and electrical components functioning within normal parameters.

Completed full HVAC system installation including 80% efficiency furnace and air conditioning unit. Installed new vertical furnace with proper venting and ductwork connections, mounted on base cabinet in basement utility area. Connected refrigerant line set with copper piping and insulated tubing, secured all connections with appropriate clamps and fittings. Installed condensate drainage system and completed all electrical connections to code. System tested and verified operational with all manufacturer specifications met.

# Water Heater Expansion Tank Leak Repair Responded to a water leak complaint involving the expansion tank mounted above the water heater. Upon inspection, confirmed active leaking from the thermal expansion tank connection point. The expansion tank exhibited significant rust-colored staining and corrosion streaking down the front surface, indicating prolonged moisture exposure from the failed connection or tank integrity compromise. Documented the condition of the complete water heating system, including the expansion tank, copper supply piping, shut-off valves, and main water heater unit. The rust deterioration pattern originated from the upper pipe connection area where the expansion tank interfaces with the copper plumbing assembly. The corrosion and staining suggested the leak had been present for an extended period, allowing mineral deposits and oxidation to accumulate on the tank surface. Photographed the installation showing the horizontal-mounted cream-colored expansion tan

Responded to service call for AC unit experiencing short cycling and condenser fan failure. Upon arrival, diagnosed outdoor condenser unit shutting down after approximately 10 seconds of operation with no fan engagement, indicating potential capacitor failure or electrical issue requiring further troubleshooting and repair.

Replaced rear exterior hose bib (faucet) on brick structure. Accessed copper supply line through interior ceiling plenum, cut and soldered new copper piping connections to install frost-free sillcock. Verified proper drainage slope and sealed exterior wall penetration to prevent water intrusion.

Completed routine maintenance visit on 4-year-old Lennox air conditioning system for MVP customer. Performed standard inspection of outdoor condenser unit, verified proper operation, and documented equipment condition with photos showing unit in good working order on concrete pad with appropriate clearances maintained.

Completed MVP cooling maintenance visit at scheduled time. Performed comprehensive system inspection including refrigerant level verification using digital manifold gauges near condensate drain lines. Inspected and serviced humidifier pad assembly, confirming proper condition of evaporator media and frame integrity. All cooling system components operating within normal parameters with no deficiencies noted.

Completed MVP cooling maintenance on three mini-split systems. Upon inspection, discovered significant accumulation of dirt, dust, and debris on evaporator coils and heat exchanger fins, with brownish-black discoloration visible across multiple surfaces. Cleaned all interior components, removed debris from unit cavities and mounting brackets, and restored optimal airflow through coil surfaces. All three units tested and confirmed operating within normal parameters upon completion.

Completed comprehensive electrical rough-in and 200-amp service upgrade for residential property. Installed junction boxes, conduit runs, and wiring throughout unfinished spaces including basement and upper floor areas, with GFCI receptacle at main panel and pull-chain lighting at panel, furnace/water heater location, and three additional basement locations for temporary power. Rough-in work includes standard lighting circuits and receptacle placement per code for all rooms, kitchen 110v circuits, exterior lighting provisions near doorways, smoke detector wiring per code requirements, doorbell transformer with dual chime connections, and bathroom exhaust fan and vanity lighting circuits in framed wall cavities awaiting drywall installation.