Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Installed a new 80% AFUE gas furnace as a complete replacement, connecting it to the existing galvanized supply ductwork with sealed, foil-taped joints and a properly routed duct elbow transition. Also installed a battery-operated carbon monoxide alarm to provide required CO detection for the new combustion appliance.

Responded to a clogged main sewer line with 2 to 3 inches of standing water covering the basement floor. Accessed the main drain cleanout and cleared the blockage with a drain machine, restoring full flow and allowing the standing water to drain. Verified proper drainage after clearing the obstruction.

Responded to a service call for a standby generator that had shut down with a fault indicator illuminated following recent maintenance, while the second unit operated normally. Inspected the generator enclosure, including the engine compartment, alternator housing, oil filter, battery connections, wiring, and base pan, and documented the unit's condition with photos. Findings and any further corrective action should be confirmed before closing the work order.

Repaired a leaking main water shut-off valve assembly by addressing the cracked nut on the city-side connection, which was causing active seepage at the valve body. The surrounding copper piping and fittings showed heavy corrosion, mineral buildup, and rust staining, so the affected connection was serviced and secured to stop the leak and restore reliable shut-off function.

Performed an on-site furnace replacement estimate, measuring the available clearance and installation space around the existing unit for proper equipment sizing and fitment. Inspected the supply plenum and duct connections, noting surface rust on the galvanized elbow, a compressed flexible duct connection at the collar, and heavy dust and debris accumulation throughout the system. Documented all findings with photos to support replacement recommendations and any necessary duct modifications.

Performed scheduled heating maintenance on a 3-year-old furnace. Removed the flame sensor, which showed heavy mineral and oxidation buildup, and cleaned the rod with an abrasive pad to restore proper flame rectification and reliable ignition. Inspected the surrounding burner compartment, wiring harness, and condensate/vent connections, and found them in serviceable condition.

Responded to a complaint of odorous water and inspected the well system, including the pressure tank, water treatment tanks with control valve, and associated piping, to determine whether the source was the water heater or the well supply. Observed a weathered, corroded pressure tank, soiled treatment tanks, and mildew growth in the utility space, and documented all conditions with photos. Findings suggest the odor is likely related to the well water and treatment system rather than the water heater, with further testing and servicing of the treatment equipment recommended.

Responded to a report of water backing up from the basement floor drain with standing water around the drain, and performed a diagnostic inspection of the floor drain and connected drain piping. Findings showed heavy staining and moisture at the drain area, along with a severely corroded drain fitting and rusted pipe rim with mineral deposits and debris buildup, indicating a deteriorated drain connection and restricted flow. Documented conditions with photos and recommended further drain clearing and repair or replacement of the corroded components.

Completed MVP heating maintenance visit on residential HVAC system. Performed thorough inspection of furnace control board, blower motor assembly, and electrical connections. Documented system operation using diagnostic equipment to verify proper voltage and amperage readings. All components found operating within manufacturer specifications, wiring connections secure, and control board functioning properly.

Attempted scheduled MVP heating maintenance visit but unable to gain access as customer did not answer door or phone. Performed exterior system diagnostics and documentation using manometer to verify static pressure readings of 0.23 inches water column and clamp meter to check electrical parameters, with amp draw reading 0.00 indicating system was not in operation at time of visit. Follow-up contact needed to reschedule complete heating system maintenance and inspection.

Responded to clogged shower drain complaint and accessed basement plumbing infrastructure to locate obstruction point. Cleared blockage from drain line using appropriate tools and verified proper water flow through the system. Inspected visible PVC drainage pipes and connections in basement area to ensure no additional issues or leaks were present, confirming all fixtures were draining correctly upon completion.

Responded to no heat call on 6-year-old Lennox gas furnace that had received heating maintenance approximately 10 days prior with all checks within normal range. Upon arrival, discovered beetle had entered the furnace control area and was causing intermittent electrical contact issues preventing ignition sequence. Removed insect from control board area, inspected all electrical connections and flame sensor, verified proper operation through multiple heating cycles. System restored to full operation with normal ignition and heating function confirmed.

Removed existing lavatory faucet and installed new Moen two-handle centerset faucet (Eva Chrome model 6410) with new pop-up drain assembly and supply lines. Inspected garbage disposal for operational issues and ordered necessary replacement parts for return visit. Completed installation of new faucet assembly with all connections tested and verified for proper function.

Completed electric vehicle charging station installation with electrical panel upgrade to accommodate increased load requirements. Installed new circuit breakers and ran dedicated wiring from the upgraded panel to support the EV charger. Additionally installed and replaced multiple electrical outlets in the garage and exterior areas of the residence to meet code compliance and customer needs.

Responded to service call for sump pump replacement in basement utility area. Removed failed existing sump pump unit and installed new replacement pump using available truck stock materials. Tested new pump operation to ensure proper functionality and water discharge, completing installation without requiring special-ordered parts.

Conducted comprehensive replacement estimate for 22-year-old residential air conditioning system. Evaluated existing HVAC infrastructure in basement utility area, including vertical air handler unit, associated ductwork, and RUUD brand equipment. Documented current system configuration with detailed photographs showing air handler placement, metallic exhaust venting, water heater proximity, and existing duct runs to provide accurate replacement specifications and equipment recommendations.

Responded to service call for 9-year-old natural gas furnace following fire department visit due to elevated CO2 levels. Performed comprehensive safety inspection of furnace and surrounding area. Upon examination, discovered heavily soiled blower wheel assembly with significant dust and debris accumulation, which can restrict airflow and impact combustion efficiency. Inspected burner assembly, heat exchanger, and venting system for potential carbon monoxide sources. Documented condition of Aprilaire 500 Series humidifier and overall HVAC system components. Blower assembly showed signs of aging with visible rust on access panel and mounting hardware. Recommended immediate cleaning of blower wheel to restore proper airflow, professional combustion analysis to verify safe CO levels, and potential heat exchanger inspection to rule out cracks or failures that could cause carbon monoxide concerns.

Responded to service call for dishwasher rerouting beneath kitchen sink. Assessed existing plumbing configuration including water filtration system, disposal unit, and supply lines in cabinet space. Successfully rerouted dishwasher drain line to accommodate cabinet layout and existing water treatment equipment, ensuring proper drainage slope and secure connections to maintain optimal appliance function.

Completed comprehensive heating maintenance service on a Ruud residential furnace system. Performed thorough inspection of all internal components including blower motor assembly, electrical connections, and wiring harnesses. Verified proper operation of all mechanical elements and confirmed system functionality upon completion.

Responded to no-heat call where furnace blower motor failed to activate. Upon inspection, diagnosed blower motor failure and assessed control board connections and gas valve assembly. Documented existing system conditions including aged plumbing infrastructure and internal furnace components showing signs of wear and corrosion for customer review and repair recommendations.