Trusted HVAC, Plumbing & Electrical Services in Canton, OH

Installed dual gas line system from existing meter to backyard patio area for future gas fireplace and outdoor kitchen. Mounted wall bracket on left side of gas meter, tapped into existing 1-inch line with tee fitting and new shut-off valve. Ran underground gas lines to two separate locations in backyard, installing underground tee to split service. Installed 3-inch PVC sleeves at both riser locations for protection. Reduced each line to 1/2-inch pipe at termination points and installed gas shut-off valves with plugs. Contractor provided trench excavation to minimum 18-inch depth and backfill services.

Replaced three old leaking radiators in upstairs bedrooms with new MR425X16 radiators measuring 4 7/16" deep, 25" high, and 16 sections (28" wide). Retrofitted existing 1" and 1 1/4" black iron piping to accommodate new units by installing 3/4" copper piping throughout. Installed new radiator valves and conical air vents on all three units to ensure proper operation and heat distribution. Fired heating system and bled air from all radiators to verify proper circulation and heat output. All three radiators now operational with no leaks detected.

Completed comprehensive heating system maintenance under the Maintenance MVP program. Performed diagnostic testing using calibrated digital measuring equipment to verify system performance and operational parameters. Inspected ductwork system including interior insulation integrity and plenum components, confirming proper installation and condition of foil-faced insulation material throughout accessible sections.

Responded to service call for leaking 40-gallon residential tank water heater. Upon inspection, confirmed active leak originating from bottom of tank, indicating internal tank failure. Unit manufactured in September 2014, showing approximately 10 years of service life. Documented existing installation configuration including copper supply lines with brass fittings, galvanized steel temperature and pressure relief valve discharge pipe, and current piping layout. Photographed unit specifications, safety labels, and installation details. Provided comprehensive quote for complete water heater replacement due to non-repairable tank breach.

Completed installation of high-efficiency furnace system with proper venting and gas line connections. Installed and secured PVC vent piping with appropriate hangers and supports, routed condensate drain lines, and connected insulated gas supply line with brass fittings and shutoff valve. Verified all ductwork connections, tested system operation, and collected final payment to close out project.

Responded to service call for malfunctioning sump pump system. Upon arrival, conducted thorough inspection of basement utility area and sump pump installation. Assessed pump functionality, discharge lines, and float switch operation. Documented existing conditions of utility sink and surrounding plumbing infrastructure through photographic evidence showing aged concrete fixtures, mineral deposits, and water staining patterns indicative of long-term usage. Completed diagnostic evaluation and provided recommendations for pump replacement or repair to ensure proper basement water management and prevent potential flooding issues.

Completed secondary installation phase for 90% AFUE furnace system. Installed and configured Aprilaire Model 60 automatic humidifier control unit with digital display, integrated into the air handler ductwork with proper drainage connections via corrugated tubing. Control unit is operational and set to maintain optimal indoor humidity levels with all indicator functions verified working correctly.

Removed and reinstalled two 2-inch flue pipes to ensure proper venting compliance and structural integrity throughout the system. Corrected outdoor terminations for both flues, ensuring proper clearances, weatherproofing, and code-compliant installation. Utilized 60 feet of 2-inch flue piping to complete the routing from heating equipment through the building structure to exterior termination points, ensuring clean penetrations through joists and proper support throughout the run.

Conducted free estimate for complete air conditioning system replacement. Existing unit is over 10 years old and has reached end of serviceable life. Documented current system conditions including deteriorated ductwork with damaged reflective insulation wrapping that requires attention during replacement installation.

Responded to kitchen sink clog with accompanying odor. Upon arrival, inspected the P-trap assembly and drainage system beneath the kitchen sink. Removed and cleaned the heavily corroded drain components, addressing significant rust buildup and debris accumulation that was causing the blockage and foul smell. Cleared the drainage line, reassembled the P-trap system, and verified proper water flow and drainage function. System tested and restored to normal operation.

Completed installation of 80% AFUE furnace unit in garage utility area. Installed air handler with proper electrical connections, condensate drain line, flexible metal conduit, and gas supply piping. Verified all wiring terminations at control board and terminal strip, ensuring proper color-coded connections for thermostat control, power supply, and safety circuits. Unit mounted securely against insulated wall with all required clearances maintained for safe operation and future serviceability.

Completed scheduled maintenance visit on 8-year-old furnace system. Performed comprehensive inspection of heating unit including visual examination of control board, wiring connections, and system components. All electrical connections verified secure, circuit board operating within normal parameters, and condensate drainage system confirmed clear and functioning properly. System tested and operating efficiently with no issues found.

Rewired dishwasher circuit to meet code requirements and customer specifications. Verified proper electrical connections, tested operation, and ensured safe functionality of the appliance circuit.

Completed routine maintenance inspection on residential boiler system for MVP customer. Performed visual assessment of teal-colored boiler unit, verified operational status of all connected components including copper piping, pressure gauge, circulator pump, and expansion tank. Documented equipment condition through photographic records showing boiler with proper ventilation, manufacturer labeling intact, and all plumbing connections secure. System found to be functioning within normal parameters with no immediate service requirements identified at time of visit.

Responded to service call for kitchen sink valve shutoff. Upon arrival, accessed under-sink plumbing area and located water supply lines serving double-basin stainless steel sink fixture. Successfully shut off supply valves to isolate water flow to kitchen sink as requested, completing valve closure operation per customer requirements.

Reconfigured circuit distribution on residential Generac backup generator transfer switch to accommodate additional loads. Relocated circuits to add master bathroom, garage door openers, and bedroom to generator coverage. Removed back bathroom circuit from transfer switch and evaluated removal of cooktop or computer room circuits to provide necessary breaker space for new load assignments. All required materials sourced from truck stock inventory. Work completed with trainee assistance over three-hour service window.

Performed safety inspection of water heater gas line and identified non-compliant flexible gas connector that does not meet current code requirements. Documented the code violation with photographs and coordinated rescheduling for proper gas line replacement with rigid black iron pipe to bring installation into compliance with safety standards.

Completed MVP cooling maintenance visit on geothermal system. Inspected control board and electrical connections within equipment cabinet, verifying proper operation of circuit board components and LED indicators. All wiring connections, including bundled purple and yellow conductors, were found secure and system controls functioning normally.

# HVAC Maintenance - Cooling Performed comprehensive maintenance service on an 8-year-old air conditioning system. Conducted electrical diagnostics using digital multimeter to verify proper voltage and amperage readings at contactor and capacitor connections. Inspected condenser coil condition, electrical wiring integrity, and all terminal connections. All components found to be operating within normal parameters with no immediate repairs required.

Completed MVP Heat maintenance service on heating system. Inspected and serviced mechanical components, filters, and ductwork assemblies as part of scheduled preventive maintenance program.