HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Performed comprehensive furnace tune-up and safety inspection. Accessed control panel to examine PCR board, verified all electrical connections and wire terminations, and inspected internal components for proper operation. Cleaned accumulated debris from blower compartment and surrounding areas to ensure optimal airflow and system efficiency.

Responded to no heat call on 5-year-old furnace. Upon inspection, identified and addressed issue with inducer motor assembly. System tested and restored to proper heating operation.

Performed comprehensive heating maintenance on a gas-powered furnace over 10 years old. Conducted thorough inspection of internal components including blower motor assembly, electrical connections, and safety controls. All wiring harnesses, wire nuts, and electrical connections were examined and found to be secure. System is operating within normal parameters and does not require equipment replacement at this time.

Completed MVP recurring maintenance visit on Lennox furnace system. Performed comprehensive system diagnostics using digital multimeter to verify electrical components and operational parameters. Inspected furnace assembly, PVC condensate drainage piping, and venting system to ensure proper function and confirm all components are operating within manufacturer specifications.

Completed scheduled MVP heating maintenance visit on Lennox furnace system. Performed comprehensive inspection of unit including blower assembly, control board, and electrical connections. Examined wire harness connections and verified proper routing of all electrical components throughout the cabinet. Inspected blower motor assembly and associated wiring for secure connections and proper operation. All system components found to be functioning within normal parameters and unit operating efficiently.

Responded to service call for leaking faucet and toilet. Upon inspection, examined kitchen faucet at base and surrounding countertop area, checking for signs of water intrusion or loose connections at the deck plate. Inspected toilet tank components and found visible water staining, mineral deposits, and sediment accumulation indicating long-term hard water exposure. Assessed flush valve assembly, fill valve mechanism, and flapper seal for proper operation and potential leak sources. Documented existing conditions of both fixtures for repair recommendations.

Completed MVP heating maintenance visit and performed comprehensive system diagnostics. Conducted combustion analysis on natural gas heating equipment, recording oxygen levels at 10.3%, carbon monoxide at 19 ppm, efficiency at 81.2%, and carbon dioxide at 6.0%. Also measured temperature differential at -0.39° to verify proper system operation and airflow performance.

Conducted comprehensive assessment of existing tanked water heater system for replacement estimate. Inspected water supply lines, shut-off valves, and copper piping connections throughout the installation area, including crawlspace plumbing infrastructure and under-sink supply connections. Documented current plumbing configuration, valve conditions, and access points to provide accurate replacement specifications and scope of work.

Replaced existing Rheem water heater with new Bradford White unit, including installation of code-compliant gas shut-off valve and thermal expansion tank to meet current plumbing standards. Completed all copper piping connections, installed pressure relief valve assembly, removed and hauled away old unit, and registered new tank with manufacturer for 6-year warranty coverage.

Responded to emergency water leak in basement with active water discharge from ceiling causing carpet saturation. Located source at corroded copper pipe connection near water heater, successfully shut off main water supply to stop flooding. Identified failed fitting with visible corrosion and mineral deposits requiring replacement; coordinated with restoration company for water damage remediation with follow-up appointment scheduled to complete permanent pipe repair once drying process is complete.

Responded to first-time service call for toilet replacement evaluation. Assessed existing white ceramic toilet with standard flush mechanism, noting internal tank components including fill valve and flush valve assembly in working condition. Provided on-site consultation and prepared replacement quote for basic American standard toilet installation. Scheduled weekend appointment per customer availability, with service call fee to be applied toward approved replacement work.

# HVAC Complete System Installation Completed full HVAC system installation including outdoor condensing unit and indoor furnace components. Installed new beige residential heat pump/air conditioner on concrete pad with proper mulch bed preparation. Ran gray flexible conduit and copper refrigerant lines from outdoor unit to indoor equipment, ensuring proper connection and secure routing. Reused existing flue system as it was determined to be in serviceable condition and compatible with new equipment. Indoor installation included new furnace unit positioned in mechanical room alongside existing water heater. Connected metal supply and return ductwork to furnace with combination of rigid silver ductwork and black flexible ducting. Ensured all manufacturer labels, warning stickers, and specification plates were properly affixed and visible per code requirements. Verified all electrical connections, refrigerant line sets, and condensate drainage were properly installed and secured. Syst

# HVAC Install - Furnace Successfully completed the installation of two 80% efficiency Lennox furnaces in residential basement mechanical room. Both units were installed side by side with proper clearances and connected to existing ductwork system. Configured supply and return air pathways using insulated flexible ductwork and metal plenums. All electrical connections were completed per manufacturer specifications and local code requirements. Units were mounted on concrete floor with appropriate leveling and secured in compliance with installation standards. Ductwork connections were sealed and insulated to prevent air leakage and ensure optimal system efficiency. Both furnace units were tested for proper operation, airflow, and safety controls. System startup procedures were performed on each unit to verify proper ignition sequence, flame sensing, and blower operation. Installation included proper labeling and documentation affixed to equipment as required by code.

Completed full HVAC system installation of an 80,000 BTU Lennox air conditioning unit at residential property. Mounted new condenser on black composite equipment pad against exterior foundation wall with proper clearance for airflow and service access. Installed gray electrical conduit along exterior wall connecting to weatherproof disconnect box with dual 20A Littelfuse fuses mounted in approved fuse holder assembly. Verified all electrical connections meet code requirements and unit is properly grounded. System tested and confirmed operational with adequate refrigerant charge and airflow. All components functioning within manufacturer specifications.

# HVAC Installation Summary Completed installation of new air conditioning system with evaporator coil for residential property. Installed evaporator coil assembly above existing Lennox furnace unit in basement location, integrating with current forced air heating system. Mounted metallic plenum housing with proper slope for condensate drainage. Connected refrigerant lines and installed condensate drain piping using white PVC with appropriate traps and fittings to prevent water backup. Secured flexible metallic duct connections to maintain proper airflow distribution. Verified all connections for proper seal and system integrity. Installation performed against exposed brick wall foundation with adequate clearance for service access. All components installed per manufacturer specifications and local building codes. --- ## Detailed Work Performed Installed complete air conditioning system including evaporator coil assembly in residential basement mechanical room. The installation int

Responded to service call regarding flickering lights in residence. Performed comprehensive electrical panel inspection and diagnosed wiring issues requiring attention. Inspected basement electrical infrastructure including exposed conduit runs and junction boxes, identifying areas with aged wiring and connections contributing to the flickering condition. Verified proper grounding at exterior meter base and evaluated service entrance conductors for integrity. Addressed electrical deficiencies found during panel inspection, secured all connections, and confirmed proper circuit loading to resolve flickering issue and ensure safe, reliable operation of the electrical system.

# Electrical Maintenance - Generator Performed routine maintenance inspection on Generac Evolution 2.0 generator system. Inspected control panel, wiring connections, and mechanical components for proper operation and condition. Discussed with customer the option of adding surge protection equipment to the associated air conditioning system for enhanced electrical protection. All generator components found to be in good working order with no immediate service needs identified. Documented equipment condition with photographs for service records.

Completed second furnace installation as part of an 80% efficiency HVAC system upgrade. Installed new residential furnace unit in basement mechanical room with proper venting connections, ductwork integration to existing distribution system, and PVC condensate drainage. Mounted and installed Kidde carbon monoxide alarm per code requirements to ensure safe operation of combustion equipment.

Responded to service call for bathtub not holding water when plugged. Inspected tub drain assembly from access point below fixture and identified faulty drain stopper mechanism preventing proper seal. Accessed underfloor plumbing through crawlspace, verified P-trap and drainage lines were clear and functioning properly. Documented existing three-handle tub valve configuration and drain assembly condition with photos for customer review and approval of recommended repairs.

Responded to service call for leaking outdoor spigot. Upon arrival, accessed the interior shut-off valve and supply lines located in the utility room mechanical space. Inspected the hose bib connection and associated plumbing, identifying the source of the leak at the exterior spigot valve stem. Replaced the faulty washer and packing, tested the system for proper operation, and verified no additional leaks were present when water was turned on and off multiple times.