HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Completed comprehensive MVP oil furnace maintenance service. Performed thorough inspection of burner assembly, motor, ignition control module, and electrical connections. All components found operating within normal parameters, system tested and confirmed functioning properly.

Responded to service call for 20+ year old gas furnace with non-operational blower motor. Upon inspection, accessed furnace system in confined basement mechanical space and assessed ductwork configuration and HVAC equipment installation. Documented existing conditions of furnace unit, ductwork connections, and overall system layout to determine cause of blower failure and restore heating operation.

Responded to no power condition at residential property. Upon arrival, confirmed complete loss of electrical power to the dwelling. Inspected main electrical service panel and determined the 100-amp main breaker had failed and required replacement. Coordinated with customer to schedule main power shutoff during preferred morning timeframe to minimize disruption. De-energized main electrical service at utility meter location. Removed failed main breaker from service panel and installed new 100-amp main circuit breaker. Verified all connections were properly torqued to manufacturer specifications. Restored main power to residence and tested all circuits for proper operation. Confirmed full restoration of electrical service to all areas of the home. System operating normally upon completion.

Replaced exterior sconce light fixture on side door with new black metal wall-mounted fixture featuring modern geometric design and glass enclosure. Customer also requested estimate for additional indoor outlet work.

Completed heating maintenance tune-up on 8-year-old Lennox gas furnace located in first-floor laundry room. Performed comprehensive inspection of unit including burner assembly, heat exchanger, ignition system, and ECM blower motor control board. Verified proper operation of hot surface igniter, gas valve, and flame sensor. Checked all electrical connections and wiring harness integrity on control boards. Inspected condensate drain lines and PVC vent piping for proper drainage and clearances. Tested system startup sequence and confirmed furnace cycled properly through all operational stages. Measured temperature rise across heat exchanger and verified within manufacturer specifications. All components found operating within normal parameters with no immediate service needs identified.

Completed routine HVAC maintenance visit for MVP customer's Lennox condensing unit. Performed system inspection, accessed electrical components and wiring connections, documented unit condition with exterior and interior photographs showing proper installation on concrete pad with all safety controls and capacitor in place.

Completed annual heating maintenance and tune-up on residential gas furnace system. Performed comprehensive inspection of furnace cabinet, blower assembly, and control board components including ECN DRIVE-24VAC module with all electrical connections verified secure. All system components including humidifier, ductwork, and exhaust venting inspected and found operating within normal parameters with no deficiencies noted.

Completed scheduled MVP heating maintenance visit on a one-year-old gas furnace system. Performed comprehensive system inspection including electrical testing with digital multimeter, verified proper operation of all components, inspected venting and PVC condensate piping, checked gas line connections and safety controls, and confirmed furnace is operating within manufacturer specifications. System is functioning properly with no issues identified during this recurring maintenance service.

Responded to service call for reported outdoor hose leak. Upon arrival, inspected exterior hose bib and associated garden hose assembly stored in container near HVAC unit on side of residence. Examined hose connections, fittings, and outdoor spigot for signs of leakage or damage. Verified system integrity and provided assessment of outdoor plumbing fixtures.

Completed heating maintenance and tune-up on 13-year-old Trane furnace system per customer request. Performed comprehensive inspection of all furnace components, verified proper operation of burners, heat exchanger, blower motor, and safety controls, and confirmed system is functioning properly. AC unit was not serviced during this visit as previously coordinated with customer.

Completed comprehensive heating maintenance on 14-year-old gas furnace system located in basement utility area. Performed thorough inspection of furnace cabinet, internal components, electrical connections, and control boards. Evaluated ductwork connections, condensate management system, and verified proper air filtration. All mechanical components, safety controls, and operational systems inspected and found functioning within manufacturer specifications for unit of this age.

Responded to follow-up service call for bathtub leak at property previously serviced two years ago. Conducted thorough inspection of bathroom plumbing fixtures and bathtub area in preparation for property sale. Documented current condition of all visible plumbing components and fixtures with photographic evidence for homeowner records.

Completed comprehensive heating maintenance on a 9-year-old gas furnace. Performed combustion analysis using Bacharach diagnostic equipment, recording optimal readings of 30 ppm CO, 9.6% O2, 6.4% CO2, and 1.84 Lambda, confirming efficient and safe burner operation. Inspected blower wheel assembly, noting dust and debris accumulation on blades and housing that could impact airflow efficiency if not addressed during future service intervals.

Removed existing water heater and installed new 40-gallon Bradford White residential water heater. Upgraded installation to current code compliance by installing new ball valve shut-off and thermal expansion tank. Connected copper supply lines and verified proper venting with existing flue system. Confirmed unit bonding and shut-off valve met code requirements. Completed all plumbing connections, tested system for proper operation and leak-free performance. Hauled away old water heater from premises. Registered new unit with manufacturer for 6-year warranty coverage.

Assessed bathroom light fixture located to the right of mirror and determined it contains an obsolete T12 15-inch fluorescent lamp with ballast and starter configuration. Advised that replacement fixture will be approximately 24 inches due to current product availability and code requirements. Parts have been ordered and received for upcoming installation to restore proper lighting functionality.

Replaced the hot side dielectric pipe assembly coming out of the water heater. The deteriorated dielectric union was removed and a new dielectric pipe connection was installed on the hot water outlet to prevent galvanic corrosion between dissimilar metals. All connections were properly secured and tested for leaks to ensure system integrity.

Completed comprehensive maintenance service on a 2-year-old Lennox residential air conditioning system. Performed standard cooling season preventive maintenance procedures including inspection of outdoor condensing unit, indoor air handler, and associated components. System evaluated and confirmed to be operating within normal parameters with no deficiencies noted requiring immediate attention.

Conducted on-site assessment for 40-gallon upright water heater replacement due to reported water leak from tank. Inspected existing unit with white exterior body and blue top cap, documenting current installation configuration including copper supply lines, brass fittings, pressure relief valve, shut-off valves with red handle, gray insulated piping, and PVC drain connections. Evaluated utility closet installation space with brown tile flooring and assessed all plumbing connections at top and base of unit. Photographed complete water heater setup showing all piping configurations, connection points, Energy Guide label, and manufacturer specifications to prepare replacement estimate. Verified 40-gallon capacity and standard residential installation requirements for accurate quote preparation.

Completed MVP recurring furnace maintenance visit, performing comprehensive system inspection and documentation. Accessed interior compartment to examine electrical components, motor assembly, wiring harnesses, control board connections, and blower wheel assembly. Inspected blower wheel and found typical dust accumulation on blades; noted 16x25x1 MERV filter specification for system. All electrical connections, wiring, and mechanical components observed to be in normal operating condition with no visible damage or deterioration requiring immediate attention.

Responded to no-cooling call where A/C unit failed to operate over the weekend. Upon inspection, discovered blown 20-amp FNR fuses in the disconnect panel. Replaced both defective fuses, restored power to the system, and verified proper operation of the air conditioning unit.