HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Performed scheduled heating maintenance service on a Lennox furnace system. Inspected furnace components including heat exchanger, ductwork connections, and exhaust ventilation. Identified minor corrosion on a component that was documented with photos, but system remains in proper working condition.

Responded to callback regarding insufficient heating issue after previous service visit on 1/8 that addressed noise concerns and included condensate pump and blower wheel cleaning. Diagnostic inspection of MVP natural gas furnace revealed improper operation of the blower motor assembly. Removed access panel, inspected wiring connections and blower components, adjusted motor settings, and verified proper operation. System now heating to set temperature with normal operation confirmed.

Responded to service call for clogged drain. Upon inspection, discovered tissue paper causing the blockage in customer's drain. Observed significant water damage on concrete floor with visible moisture spread and discoloration. Successfully cleared the obstruction and verified proper drainage functionality.

Performed scheduled furnace maintenance service (rolled appointment). Conducted thorough inspection of furnace control board and electrical connections. Utilized hex key tool to make necessary adjustments to system components. All connections verified secure and operational.

Performed routine tune-up service on a 2-year-old furnace system. Inspected air filter housing and confirmed filter is clean and properly installed. Examined furnace unit with PVC venting system, verified all connections are secure, and confirmed system operation is within normal parameters.

Performed scheduled MVP Heating maintenance service which included inspection and cleaning of the blower wheel assembly that showed light dust accumulation. Inspected electrical connections and terminal components, ensuring proper mounting of connectors and verifying integrity of wiring harness including red, yellow, and green wires.

Performed scheduled MVP heating maintenance service. Utilized hex key tools to make necessary adjustments to heating system components. Completed all standard inspection and maintenance protocols as per recurring service requirements.

Performed scheduled MVP Heating service on Lennox system. Inspected control board connections and verified proper wire terminal connections using hex key. All electronic components on PCB were in good condition with no visible damage or corrosion.

Completed scheduled MVP Heating maintenance visit. Inspected system components including evaporator coil and air filter. Used diagnostic probe tool to examine internal components, confirming proper operation of the heating system with no issues detected.

Performed rescheduled furnace maintenance on 5-year-old unit for MVP customer. Inspected evaporator coil, condensate drainage system, and heat exchanger. System appears to be functioning properly with normal signs of operational wear.

Investigated water leak from main floor bathroom into basement in 1942 home. Visual inspection revealed moisture staining at bathroom fixture base with discoloration where floor tiles meet the porcelain. Further examination of the basement ceiling/joists showed water damage along pipe pathways with visible PVC and copper plumbing lines. Repaired leaking pipe connection and sealed fixture base to prevent future water intrusion.

Successfully completed the ignitor replacement service as ordered. The faulty ignitor was removed from the heating system and the new replacement part was properly installed and tested for proper operation.

Performed scheduled tune-up service on a 7-year-old Lennox furnace system. Completed comprehensive inspection and maintenance procedures according to manufacturer specifications. System is operating properly with no immediate concerns identified.

Responded to no heat call for 20-year-old furnace that was restarting but operating at reduced capacity with constant beeping. Diagnostic inspection revealed failing blower motor with deteriorated wiring connections and a compromised control board showing signs of electrical component failure. Replaced blower motor assembly and control board to restore proper system functionality and eliminate alarm condition.

Performed annual maintenance on 6-year-old furnace. Inspected and replaced air filter with new pleated filter to ensure proper airflow. Examined control board and wiring connections in electrical panel, confirming all components are securely connected and functioning correctly.

Completed routine maintenance on a 2-year-old furnace previously installed by Blind and Sons. Performed comprehensive diagnostic testing using multimeter readings (15.13 and 49.7) to verify proper electrical operation and system functionality. All systems operating within manufacturer specifications after tune-up.

Performed scheduled maintenance on 7-year-old heating system. Inspected furnace components including control board, wiring connections, and ventilation ducts. Used specialized tool to make necessary adjustments to system. All components verified to be properly connected and functioning correctly.

Performed routine MVP heating maintenance service including filter replacement on residential furnace system. Inspected complete HVAC setup including main furnace unit, PVC ventilation pipes, and auxiliary wall-mounted component. System appears properly installed with all connections intact and functioning normally.

Performed scheduled MVP Heating maintenance service on a 4-year-old system (rescheduled from 11/6). Inspected air filter which showed significant dust accumulation indicating replacement is needed. Examined control board and wiring connections, ensuring all electrical components were properly secured and functioning.

Performed routine maintenance on 3-year-old furnace (rescheduled from 11/11). Replaced air filter with new pleated filter and conducted system inspection using hex key to check mechanical components. System is functioning properly after service.