HVAC, Plumber & Electrician Services in Fairlawn, OH

Completed comprehensive gas furnace maintenance inspection and diagnostics. Performed system evaluation with digital instrumentation to verify proper operation and temperature readings. Removed and assessed evaporator coil condition, noting accumulated dirt and debris on fins requiring cleaning to maintain optimal airflow and heat transfer efficiency.

Completed MVP cooling maintenance visit on HVAC system. Performed electrical diagnostics using clamp meter, recording amperage readings of 4.42A and 0.67A on system components. Inspected condenser coil fins, which were found to be clean and in good operating condition.

Completed routine maintenance on a 2-year-old gas furnace. Accessed control cabinet, inspected internal components including control board and blower motor assembly, verified all electrical connections and wiring harnesses were secure, and referenced manufacturer specifications for proper venting configuration to ensure system compliance with installation requirements.

Completed scheduled MVP heating maintenance visit. Performed comprehensive inspection of gas furnace system, verifying proper operation of burner assembly with all three burners igniting and producing proper blue flames. Examined gas valve assembly, electrical connections, and safety controls including limit switches and flame sensor. Inspected venting system including PVC intake and exhaust piping, confirmed proper installation and secure connections. Verified gas line connections for leaks, checked all wiring terminations, and ensured access panels were properly secured upon completion. System operating within manufacturer specifications with no deficiencies noted.

Completed installation of 80% AFUE high-efficiency gas furnace in residential utility closet. Unit installed with proper clearances, metallic supply ductwork connected to existing distribution system, and black PVC condensate drain piping routed with appropriate traps and termination. All electrical connections, gas line hookup, and combustion air provisions completed per manufacturer specifications and local code requirements.

Responded to E32 venting error code on 8-year-old Trane gas furnace. Upon inspection, identified pressure switch issue causing false venting fault. Removed access panel, tested pressure switch and inducer motor operation, cleared debris from pressure tubing, verified proper draft operation, and confirmed system returned to normal heating cycle with error code cleared.

Completed comprehensive duct cleaning service for newly constructed residential property with approximately 14 supply and return vents. Pre-service inspection revealed significant accumulation of construction debris, drywall dust, and particulate matter throughout the ductwork system—common in new home installations. Utilized professional rotary brush system and negative air machine to thoroughly clean all accessible duct runs, including flexible and rigid metal ductwork. Removed heavy deposits of fine dust and debris from duct floors, walls, and interior surfaces, restoring proper airflow capacity and improving indoor air quality for the new homeowners.

Conducted comprehensive furnace replacement estimate at residential property. Evaluated existing gray metal furnace unit in basement mechanical room, documenting current system configuration including white PVC venting, copper gas line routing, and auxiliary humidifier component. Assessed equipment age, condition, and compatibility requirements for replacement system recommendations, capturing detailed photos of existing installation for proposal development.

Completed comprehensive heating system maintenance inspection on HVAC unit. Thoroughly examined evaporator coil assembly, noting copper piping connections showing age-appropriate oxidation while aluminum fins remained in clean, serviceable condition. Inspected blower wheel assembly, documenting dust accumulation on blades and verifying proper mechanical operation of all components.

Conducted estimate for furnace replacement due to water damage originating from upstairs unit. Inspected existing Lennox furnace system and associated ductwork, noting compromised components from water intrusion. Documented current HVAC installation including furnace unit, supply and return ductwork, condensate drainage system, and copper refrigerant lines. Evaluated water heater and related plumbing infrastructure in mechanical room to assess extent of damage. Provided comprehensive replacement estimate with loss, rent, and displacement considerations for complete system restoration.

Responded to service call for furnace that would not shut off despite thermostat indicating 75 degrees. Upon inspection, diagnosed thermostat malfunction preventing proper communication with heating system. Verified furnace operation and cycling controls, confirming unit was functioning mechanically but receiving continuous call for heat due to faulty thermostat signal.

Completed comprehensive plumbing fixture replacement throughout the residence, including kitchen undermount sink installation with integrated reverse osmosis system, garbage disposal unit, and faucet assembly. Replaced faucets in powder room, secondary bathroom (sink faucets and shower/tub fixture), and laundry room sink. All fixtures were properly installed, water supply lines connected, tested for leaks, and confirmed operational before completion.

Completed comprehensive heating maintenance tune-up on 7-year-old Armstrong air handling unit in preparation for winter season. Performed full system inspection including heat exchanger evaluation, evaporator coil assessment, electrical connections check, and refrigerant line inspection. System tested and confirmed operational with all components functioning properly.

Performed descaling service on Bradford White BRLITE FT combi unit as requested on second service call. Addressed mineral buildup affecting system performance by completing thorough descaling procedure on the combination heating and domestic hot water unit, restoring proper operation of the hydronic heating system and connected zones with circulator pumps.

Completed preventive maintenance service on a 3-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including cleaning of exterior surfaces, verification of refrigerant line insulation integrity, and operational testing of all components. Unit found to be functioning within normal parameters with no immediate service requirements identified.

Completed routine MVP cooling maintenance visit on Lennox outdoor condensing unit. Performed comprehensive system inspection, verified proper operation of all components, and measured supply air temperature at 52.3°F, indicating normal cooling performance. Unit exterior and internal components showed no signs of damage or excessive wear, with clean housing and proper airflow through louvered panels. All systems operating within manufacturer specifications.

Completed comprehensive cooling maintenance on a 7-year-old air conditioning system. Performed temperature diagnostics on supply ductwork, recording 63.7°F at the plenum, indicating proper system operation and adequate cooling output. Inspected condenser coil, evaporator assembly, refrigerant lines with insulation, and all associated HVAC components including furnace cabinet and humidifier unit. System operating within normal parameters with no deficiencies noted.

Performed scheduled annual maintenance on residential standby generator system. Conducted comprehensive inspection of all electrical connections, verified proper operation of transfer switch, and tested automatic start functionality. Replaced air filter element, checked fluid levels, and confirmed unit operates within manufacturer specifications.

Completed routine maintenance on 15-year-old air conditioning system. Performed comprehensive inspection of all major components including blower motor assembly, control boards, electrical connections, and wiring. Verified proper operation of dual circuit boards, checked all wire connections and terminals for secure attachment, and inspected capacitor mounting. All components found to be in operational condition with no immediate repairs required.

Responded to service call for slow draining in main bathroom. Performed main drain cleanout to address drainage issue and restore proper flow through the plumbing system. Inspected basement plumbing infrastructure including vertical drain lines, PVC piping configuration, and main drain access points to ensure complete clearance and verify system functionality.