HVAC, Plumber & Electrician Services in Fairlawn, OH

Completed installation of 80% AFUE furnace and air conditioning system at residential property. Installed new Lennox outdoor condensing unit on rubber isolation pad against exterior wall with proper clearances maintained. Unit positioned on level pad with electrical disconnect box mounted to building exterior and refrigerant line set routed through wall penetration. Installed new fuse block assembly with appropriately rated FLNR and FRE30R fuses for overcurrent protection of equipment. Connected copper wiring to fuse block terminals and secured all electrical connections per manufacturer specifications and local electrical codes. Routed electrical conduit along exterior siding to disconnect box. Verified proper grounding of all components. System installation completed in damp weather conditions. All equipment secured and operational.

Responded to service call for clogged sump pump discharge piping. Upon arrival, observed water spitting from discharge line connection point near gutter drainage area during pump operation. Performed mechanical snaking of discharge line to clear blockage and restore proper drainage flow. Verified sump pump cycling and confirmed discharge piping was draining freely without backup or leakage at connection points. System returned to normal operation with water properly evacuating through discharge line.

Completed annual air conditioning maintenance on 1-year-old Lennox cooling system. Performed comprehensive system inspection including outdoor condenser unit evaluation, refrigerant level verification, electrical connection testing, and component cleaning. Accessed upper level crawl space to inspect and service air filters, examined ductwork system throughout attic space including black flexible duct runs for proper airflow and connections. Provided thermostat operation instruction to restore system functionality. All components found operating within normal parameters with no deficiencies noted.

Responded to service call for inoperative hot water heater in 50-year-old residence. Upon arrival, inspected AO Smith 100-gallon tanked water heater located in basement utility area. Unit was not producing hot water as reported. Conducted diagnostic assessment of water heater system, including examination of heating elements, thermostat functionality, gas supply connections, and associated plumbing infrastructure. Evaluated copper and steel piping network, shut-off valves, and pressure relief valve for proper operation. Documented existing installation configuration with exposed brick and concrete block walls in unfinished basement setting. Assessed overall condition of unit and surrounding plumbing connections. Provided technical findings and recommendations to homeowner regarding repair or replacement options based on age and condition of existing equipment.

Completed BS-MVP recurring cooling maintenance visit on residential HVAC system. Upon arrival, performed comprehensive inspection of outdoor equipment including triangular A-frame evaporator coil and associated air handler unit. Documented heavy accumulation of dirt, debris, and organic matter on evaporator coil fins, which was significantly restricting airflow and reducing system efficiency. Cleaned and serviced evaporator coil assembly to restore proper heat transfer capability. Inspected flexible ductwork connections and verified proper sealing. Checked concrete pad mounting and equipment positioning. System operational following maintenance procedures.

Completed comprehensive air conditioning tune-up and maintenance on a 12-year-old residential AC system. Performed standard preventive maintenance procedures including inspection of the Lennox furnace and associated HVAC components, verified proper operation of all system controls, checked refrigerant levels, cleaned condenser coils, inspected electrical connections, and tested airflow throughout the system. All equipment found to be operating within manufacturer specifications with no immediate repairs required at this time.

Completed MVP recurring cooling maintenance visit. Performed system inspection including examination of control board components and condenser coil condition. Documented equipment status with photos showing circuit board configuration and heat exchanger fins with minor dust accumulation noted on coil surfaces.

Completed scheduled MVP heating maintenance visit on Lennox furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, gas valve connections, electrical wiring harness, and control board. Verified proper operation of all safety controls, checked gas line connections for leaks, and confirmed secure wire terminations throughout the system. All components found in good working order with no issues identified. Unit operating within manufacturer specifications.

Completed comprehensive duct cleaning service for residential HVAC system covering up to 14 vents. Pre-service inspection revealed significant accumulation of dust, debris, and particulate matter throughout the ductwork, particularly in main trunk lines and branch connections. Utilized professional-grade vacuum equipment and rotary brush system to thoroughly clean all accessible ductwork, removing built-up contaminants from interior surfaces and restoring proper airflow capacity throughout the ventilation system.

Completed preventive maintenance cooling visit on an 8-year-old HVAC system. Inspected air handler components, ductwork connections, and condensate drain system; verified proper operation of all mechanical components and documented system condition with photographs. All equipment found to be functioning within normal parameters with no immediate service needs identified.

Completed scheduled MVP cooling maintenance visit on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified electrical readings using digital multimeter, and confirmed proper system operation. All components found to be functioning within normal parameters.

Responded to service call for 10-year-old air conditioning system during scheduled MVP maintenance visit. Performed comprehensive system inspection of outdoor condenser unit and interior mechanical components, including examination of refrigerant lines, copper tubing, control valves, and associated piping. Documented equipment condition through photographic records showing normal wear patterns on copper lines and verified proper mounting and accessibility of all service components within the mechanical cabinet.

Conducted complimentary on-site consultation to provide toilet replacement quote and review available fixture options with customer. Assessed existing toilet condition and bathroom configuration, documented current installation with photographs, and discussed customer preferences for new toilet models including features, specifications, and installation requirements.

Completed comprehensive AC tune-up on residential split system with Lennox furnace and outdoor condensing unit. Performed standard maintenance procedures including inspection of electrical components, refrigerant lines, condensate drainage system, and both indoor and outdoor equipment. All systems operating within normal parameters upon completion.

Provided comprehensive estimate for complete furnace and air conditioning system replacement. Assessed existing equipment location in utility area and evaluated attic access point for new installation requirements. Documented current system configuration including accessibility, clearances, and structural considerations necessary for equipment upgrade.

Responded to service call for persistent sewer odor in basement and bathroom areas. Performed comprehensive assessment of plumbing system to identify source of sewer gas infiltration. Replaced two defective wax ring seals on toilet fixtures that were allowing sewer gases to escape into living spaces. Inspected drain waste vent system and conducted smoke testing to verify integrity of plumbing connections and identify any additional leak points. Examined basement utility sink area and associated drain lines for potential trap seal failures or venting issues. Verified proper operation of all fixtures following repairs and confirmed elimination of sewer odor issues throughout affected areas.

Completed kitchen sink conversion from double-basin to single-basin configuration with new undermount stainless steel sink installation. Installed garbage disposal unit and reconfigured drain plumbing with PVC P-trap assembly to accommodate new sink layout. Provided quote for whole house water filtration system as requested.

Completed comprehensive MVP AC maintenance on residential cooling system. Performed thorough inspection of indoor air handler unit and outdoor condensing unit, including examination of electrical connections, contactor operation, and refrigerant line insulation. Verified all wiring connections were secure with proper color coding, checked control panel components for proper operation, and documented system condition through detailed photography of both indoor and outdoor equipment.

Replaced defective Kohler flush valve seal and fill valve to restore proper toilet operation. Parts were ordered and picked up for installation, resolving issues with tank filling and flushing performance.

Met with inspector on site for final inspection approval. Documented compliance verification with photos showing approved County of Summit compliance sticker affixed to electrical installation, confirming work meets code requirements and has passed inspection.