Trusted HVAC, Plumbing & Electrical Services in Macedonia, OH

Performed MVP heating maintenance on the upright gas furnace/air handler, inspecting the cabinet interior, blower housing, and control board with its terminal strip connections and wiring harness for secure terminations and signs of damage. Verified the PVC condensate drain line and trap are properly routed and unobstructed, and confirmed the supply ductwork and galvanized trunk seams are sealed with no visible rust, frost, or physical damage. Unit is in good working condition with no deficiencies noted at completion.

Performed seasonal heating maintenance on a 6-year-old gas furnace, inspecting internal components and the burner compartment. Inspected the flame sensor and hot surface igniter, noting tarnishing and wear on the sensor rod and mounting hardware, with iridescent discoloration on the igniter blade; cleaned the components and verified secure mounting and proper operation.

Performed annual heating maintenance on a 12-year-old gas-fired furnace, including a visual inspection of the cabinet, condensate pump, drain piping, and electrical connections. Used a borescope to inspect the interior heat exchanger and flue passages, finding no visible cracks, corrosion, or obstructions. Verified the condensate pump and drain line were intact and free of leaks, and confirmed the galvanized mounting bracket was clean and undamaged.

Installed a new 40-gallon tall Bradford White gas water heater (model RG140T6N), including a new ball valve on the water supply and an additional sweat-type secondary main water shut-off valve. Bonded the gas line and supported it with double unistrut and strut clamps. No expansion tank was required per current code, as there is no check valve in the supply line.

Completed annual maintenance and tune-up on an 8-year-old Lennox ML193UH090XP48C gas furnace. Performed comprehensive system diagnostics including voltage testing at electrical connections, which measured 46.6 volts at the control board wiring harness. Inspected all internal components, refrigerant lines, and gas valve assembly for proper operation and wear patterns. System tested and verified operational within manufacturer specifications.

Conducted free estimate for replacement of 30-year-old water heater located in narrow basement utility closet. Assessed existing installation and confirmed requirement for tall slim profile unit due to confined space constraints. Documented existing conditions including aging galvanized tank, copper supply piping, and venting configuration in preparation for replacement proposal.

Performed complete flush and fill service on a 7-year-old Rheem Performance 40-gallon residential water heater as part of pre-sale home maintenance. Drained sediment buildup from tank bottom, flushed system thoroughly to remove mineral deposits and debris, then refilled unit and verified proper operation of all valves, connections, and safety components. This was the first professional maintenance service performed on this unit since installation.

Completed comprehensive duct cleaning service for residential HVAC system. Accessed and cleaned main supply and return ductwork, removing accumulated dust and debris from interior metal surfaces. Documented pre-service conditions showing typical dust accumulation on galvanized sheet metal duct walls and inspected all accessible plenum chambers and duct passages for proper airflow and structural integrity.

# HVAC Heating Maintenance Completed Performed comprehensive MVP heating maintenance on residential forced air furnace system. Conducted thorough inspection of furnace unit, verified proper operation of all mechanical components, and checked refrigerant lines and ductwork connections for integrity. Examined condensate drainage system with white PVC piping to ensure proper flow and prevent backup issues. Inspected thermostat control functionality and verified accurate temperature regulation. Assessed all visible ductwork including flexible black ducts and metallic supply runs for secure connections and proper airflow. Confirmed water heater and associated plumbing systems in mechanical room were operating safely alongside HVAC equipment. System operating within normal parameters with no immediate concerns identified.

Completed scheduled MVP heating maintenance visit on residential forced-air furnace system. Performed comprehensive inspection of gas furnace unit and associated components, including blower motor assembly, electrical connections, and internal mechanical systems. Accessed lower furnace panel to examine wiring harnesses, burner assembly, and safety controls. Verified proper operation of heating equipment, checked gas piping connections for integrity, and inspected ductwork connections. Confirmed 16x20x2 filter specification marking on unit. System found operating within normal parameters with all components functioning properly.

Completed comprehensive MVP Heat maintenance on a 10-year-old gas heating system. Inspection revealed significant corrosion and rust accumulation on the heat exchanger coils and interior components, along with substantial dust and debris buildup on the blower wheel assembly. Thoroughly cleaned the blower motor and fan blades, removed debris from the evaporator coil area, and documented the advanced deterioration of internal metal surfaces showing moisture exposure and oxidation. System operational at time of completion, though visible corrosion on heat exchanger components and interior surfaces indicates the unit has been subjected to prolonged humidity exposure and may require monitoring for future performance issues.

Performed comprehensive duct cleaning service for residential HVAC system, removing accumulated dust and debris from interior ductwork surfaces. Additionally completed dryer vent cleaning to ensure proper airflow and reduce fire hazard risk.

Provided comprehensive estimate for replacement of 18-year-old residential air conditioning system experiencing refrigerant leak and low charge. Evaluated existing outdoor condenser unit positioned on concrete pad against exterior brick wall, assessed property specifications including 1,200 square foot main level, 900 square foot basement, and insulated attic space. Presented equipment options and financing solutions for air conditioning replacement to address aging system and refrigerant loss issues.

Installed a pressure reducing valve with ball valve assembly after the water meter, including necessary brass fittings and couplings to regulate incoming water pressure. Replaced the deteriorated fill valve and corroded supply line on the first-floor toilet, addressing significant rust buildup and mineral deposits within the tank. All components were tested for proper operation and leak-free connections upon completion.

Performed site assessment for electric vehicle charging station installation feasibility in residential garage. Evaluated existing electrical panel capacity and determined available breaker spaces for dedicated EV charger circuit. Documented current electrical infrastructure including panel location, available conduit pathways, and optimal charging station mounting location near vehicle parking area to provide homeowner with installation options and requirements.

Responded to complaint of loud noise followed by prolonged hissing sound from toilet. Upon inspection, diagnosed faulty fill valve causing the reported symptoms. Checked home water pressure at exterior pressure regulator, which measured within normal operating range. Inspected interior plumbing connections and shut-off valves for proper operation. Replaced defective toilet fill valve assembly to eliminate noise and hissing issue. Tested toilet flush cycles to verify proper fill operation and confirm resolution of problem. System now operating quietly and efficiently.

# HVAC Maintenance - Cooling Performed annual preventive maintenance on 1-year-old Lennox air conditioning system. Completed comprehensive inspection of indoor air handler unit including electrical components, capacitor testing, and control board verification. All electrical connections were secure with proper wire management observed. System capacitor tested within manufacturer specifications. Inspected condensate drainage system with PVC piping confirmed clear and functioning properly. Unit operating efficiently with no deficiencies noted. Service completed to accommodate customer's scheduling requirements.

Successfully removed and replaced the existing 1 1/2" kitchen drain line in the basement ceiling, upsizing to 2" piping for improved drainage capacity. Cut out the old line above the 90-degree elbow fitting and installed a new 90-degree elbow oriented forward along the joist direction. Installed a new 3"x2" wye fitting on the main horizontal drain line to properly integrate the upgraded kitchen drain. All work performed with new PVC piping and fittings to ensure code compliance and long-term reliability. Protected work area with drop cloths and restored basement to clean condition upon completion.

Conducted comprehensive electrical estimate for generator installation. Evaluated existing electrical service panel and circuit breaker configuration, documenting current 2-pole breaker setup rated at 120/240V AC with 200kA interrupting capacity. Assessed site conditions including plumbing infrastructure and building layout to determine optimal generator placement and electrical connection requirements. Photographed electrical panel specifications and work area to provide detailed documentation for generator sizing, transfer switch installation, and necessary electrical modifications.

Completed MVP annual cooling maintenance on 8-year-old residential air conditioning system. Performed comprehensive inspection of indoor air handler components including blower motor assembly, electrical connections, and control board. Verified proper operation of all electrical components and connections. Inspected outdoor condensing unit positioned on concrete pad with rock bed surround. Confirmed unit is level and properly supported on pavers. Checked refrigerant levels, tested system operation, and verified airflow. All components functioning within normal parameters. System operating efficiently with no issues identified.