Trusted HVAC, Plumbing & Electrical Services in Macedonia, OH

Completed scheduled AC tune-up on Lennox HVAC system. Performed comprehensive inspection of furnace unit, ductwork connections, condensate drainage system with PVC piping, and all associated components. All equipment found operating within normal parameters with no issues identified during service visit.

Responded to follow-up service call regarding unplugged opening in furnace piping left from previous heating maintenance visit. Located and inspected the open hole in pipe, documented crack and damage visible in the interior surface of the cylindrical duct with photographic evidence. Successfully sealed and plugged the opening to restore system integrity and prevent air infiltration that could compromise heating efficiency.

Replaced defective circuit board and flame sensor on heating system. Upon installation of new components, verified proper system operation with all indicator lights functioning correctly and unit cycling normally. Confirmed all electrical connections secure and refrigerant lines properly positioned.

Completed comprehensive AC tune-up on outdoor condenser unit, including visual inspection of cylindrical cage housing, aluminum fins, and electrical components. Unit operational with no immediate service concerns identified; all components functioning within normal parameters at time of inspection.

Completed routine heating maintenance on 25-year-old gas furnace as part of recurring service agreement. Performed standard inspection and cleaning procedures on furnace components. Documented interior ductwork condition, noting dust accumulation and minor discoloration at seam joints. Customer requested quote for reinstallation of previous thermostat due to dissatisfaction with current unit.

Responded to no-heat call with E270 error code on furnace unit. Accessed internal components through front panel, inspected blower motor, electrical connections, gas line fittings, and PVC exhaust/intake piping system for proper operation and diagnostic troubleshooting. Verified all mechanical and electrical components, resolved error code, and restored heating system to normal operation.

Removed and replaced existing 50-gallon Rheem power vent water heater with new 50-gallon Bradford White power vent unit. Installation included new expansion tank and water shut-off valve to bring system up to current plumbing code standards. All connections were secured with copper piping, and the power vent exhaust system was properly configured for safe operation. Unit is covered under an 8-year tank warranty and was tested for proper function upon completion.

Completed comprehensive furnace tune-up on 5-7 year old unit, performing standard maintenance procedures including burner inspection, heat exchanger examination, and blower assembly service. Accessed and adjusted gas valve components using proper hand tools, verified all electrical connections, and ensured system is operating within manufacturer specifications for optimal performance and safety.

Replaced existing Mansfield toilet on second floor with new American Standard Cadet chair height model featuring elongated bowl and installed new shut off valve. Replaced front home sillcock with new Woodford frost-free unit, which required opening drywall to access interior piping and installing access panel for future maintenance accessibility.

Completed preventative maintenance on Lennox outdoor condensing unit. Inspected and tested electrical components including 30-amp renewable fuses, verified proper amperage and connections. Unit operating within normal parameters, all safety controls functional.

Responded to no hot water complaint at 27-year-old residence with existing tanked water heater system. Upon arrival, assessed Rheem residential water heater unit and associated plumbing infrastructure including expansion tank, copper supply lines, shut-off valves, and circulating pump assembly. Inspected all connections, electrical components, and safety labels for proper operation and code compliance. Documented existing installation showing water heater with integrated expansion tank, PVC venting system, copper water lines with red-handled ball valves, and recirculation pump mounted at top of unit. Verified all plumbing connections, valve operations, and system components. Photographed complete installation for service records showing proper configuration of hot and cold water lines, expansion tank mounting, electrical connections, and venting arrangement in basement mechanical room.

# HVAC Complete System Installation Successfully completed installation of a high-efficiency 80% AFUE gas furnace with matching air conditioning system and whole-home humidifier. The new furnace unit was positioned in the attic space with proper clearances and ventilation requirements met per manufacturer specifications. Refrigerant lines were professionally routed and insulated, connecting to brass service valves with appropriate gauge fittings for future maintenance access. All electrical connections were completed to code, including installation of 25-amp Littelfuse NR fuses in the outdoor disconnect for overcurrent protection of the condensing unit. The system was pressure tested for leaks, evacuated, and charged with refrigerant to manufacturer specifications. Humidifier integration was completed with proper water supply and drainage connections to the furnace plenum. All components were tested for proper operation, including heating cycle, cooling cycle, and humidification funct

# Plumbing Service - Sold Repair Summary Successfully installed a new 40-gallon Bradford White water heater with 6-year manufacturer warranty, including a new ball valve, thermal expansion tank, and gas line modification to relocate the fireplace tee above the water heater shutoff valve. ## Work Performed Removed existing water heater and prepared the installation area in the basement utility space. Installed the new 40-gallon Bradford White residential water heater in compliance with manufacturer specifications and local plumbing codes. Connected a new cream-colored thermal expansion tank to the cold water supply line using copper piping and brass fittings. The expansion tank was properly mounted and secured above the water heater unit to manage thermal expansion and protect the system from excessive pressure buildup. Installed a new ball valve on the water supply line to provide proper shutoff capability for future maintenance and emergency situations. All water connections were

# Service Summary Completed scheduled furnace tune-up maintenance visit confirmed for 8am arrival. Performed standard seasonal inspection and servicing of heating system to ensure optimal performance and efficiency for upcoming heating season. # Work Performed Conducted comprehensive furnace tune-up including visual inspection of all accessible components. Verified proper air filter installation and condition - filter found to be clean and correctly seated within the return air housing with secure mounting. Inspected furnace cabinet access and surrounding work area. All system components accessible and operational at time of service. Equipment found in satisfactory working condition with no immediate repairs required. Standard preventive maintenance procedures completed per manufacturer specifications.

# Plumbing Service Report ## Service Summary Responded to toilet repair request at 32-year-old residential property. Diagnosed and addressed internal tank component deterioration and mineral buildup affecting flush performance. ## Work Performed Upon arrival, conducted visual inspection of toilet fixture and internal tank components. Removed tank lid to assess flush mechanism condition. Found significant mineral deposits and rust-colored sediment accumulated on tank floor, indicating corrosion of metal components and water quality issues. Water in tank exhibited brownish discoloration consistent with iron content or deteriorating internal hardware. Inspected flush valve assembly with float ball and chain mechanism, noting age-related wear on black plastic components. Examined fill valve and overflow tube assembly for proper operation. Identified corroded metal hardware within tank requiring attention to prevent future leaks and ensure reliable flushing action. Verified water suppl

Conducted HVAC system assessment of existing furnace unit installed in utility closet. Inspected aging system components including ventilation, PVC drainage pipes, and connections. Provided comprehensive replacement estimate for complete HVAC system upgrade based on current equipment condition and household requirements.

Performed scheduled BS-MVP Heating maintenance visit. Inspected blower wheel assembly, which showed normal dust accumulation on the metal blades but remains in proper operating condition. Used diagnostic probe to test system functionality; all components operating within specifications.

Completed replacement of waste and overflow with new lift and turn style, and installed new Moen single-handle tub/shower valve. Installation included adding shut-off valves on water lines in the access panel for improved serviceability, with all new components properly connected to existing PVC and copper supply lines.

Responded to service call for 2012 water heater with declining hot water output. Inspection revealed deteriorated insulation around water heater pipes with visible damage at pipe penetration points, exposing underlying fiberglass insulation. Repaired pipe insulation and performed maintenance service to restore proper hot water functionality.

Completed installation of a Navien NPE tankless water heater to replace the existing 50-gallon Rheem power vent unit. Mounted panel board, connected to existing water and gas lines, and installed fresh air intake to current PVC exhaust pipe. Added required access panels in soffit for strapping and fitting access, with exhaust routed through soffit and exiting the rear of the house east of the outside faucet.