Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Completed comprehensive AC tune-up including full system inspection and performance testing. Applied weatherproof caulking around refrigerant line penetration through exterior siding to seal against moisture infiltration and improve energy efficiency.

Completed MVP AC maintenance on Lennox HVAC system in basement utility room. Performed comprehensive cooling system inspection, including examination of furnace unit, electrical connections, and associated components. Inspected terminal block connections with multiple colored wires, noting dust accumulation and environmental exposure typical of basement installations. Verified proper operation of white PVC exhaust and intake vent pipes extending from furnace top. System operational and ready for cooling season.

Responded to failed electrical inspection for warranty work. Corrected improper PVC conduit installation by applying approved solvent cement to all unglued joints and replaced non-compliant straps with appropriate electrical-rated hangers per NEC requirements. All conduit runs secured properly to structural members with correct spacing. Work inspected and approved for code compliance.

Installed exterior gas line test setup with gray PVC piping configuration including horizontal and vertical runs, incorporated red-handled ball valve for system control, and secured all components with proper pipe straps and supports against building exterior. Installation completed over decorative river rock ground cover with all connections, T-joints, and elbow fittings properly assembled and tested for system integrity.

Completed full ductless mini-split system installation including attic-mounted air handler with new ductwork distribution and single indoor wall-mounted head unit. Installed gray metal air handler on platform between attic joists with proper structural support, ran flexible supply and return ductwork throughout attic space with appropriate insulation, and mounted interior ceiling register with white louver grille for conditioned air distribution. Installed indoor ductless head unit in living space with thermostat control panel for zone temperature management, ensuring proper refrigerant line connections, condensate drainage, and electrical service to both indoor and outdoor components for complete system operation.

Responded to service call regarding clogged discharge line on 3-year-old outdoor heat pump unit. Upon arrival, performed comprehensive system inspection including removal of access panel to examine electrical components, capacitor (440V 45/9.5 MFD), control board connections, and wiring integrity. Cleared condensate drain line obstruction and verified proper drainage through PVC condensate piping system. Inspected indoor air handler unit and condensate trap assembly, noting moisture accumulation on utility room floor. Completed standard maintenance procedures including checking all electrical connections, verifying proper voltage supply, and ensuring system operational parameters were within manufacturer specifications. Unit tested and returned to normal operation with proper condensate drainage flow restored.

Completed MVP cooling maintenance visit on residential Lennox outdoor condensing unit. Performed standard system inspection and operational checks. Verified supply air temperature at 52°F through ductwork measurements, confirming proper cooling performance. Unit operating within normal parameters with no deficiencies noted. System maintaining adequate airflow and temperature differential for effective climate control.

Completed MVP cooling maintenance visit on 6-year-old Goodman air conditioning system. Performed comprehensive inspection of outdoor condenser unit and indoor air handler, verifying proper operation of all mechanical and electrical components. Inspected blower motor assembly, squirrel cage fan wheel, control board connections, and capacitor. All system components found to be in good operating condition with no deficiencies noted.

Completed MVP recurring cooling maintenance visit on 14-year-old Carrier HVAC system. Performed comprehensive inspection of indoor unit components including control board, electrical connections, capacitor, and blower motor assembly. Verified proper operation of all system controls and safety devices. Documented equipment condition through photographic records showing accessible components within cabinet and overall installation configuration. All components found operating within normal parameters for unit age.

Completed MVP cooling maintenance visit on 3-year-old Lennox outdoor condensing unit. Performed standard preventative maintenance protocol including filter inspection and cleaning, with before and after documentation showing significant dust and dirt accumulation on intake filters. Unit is properly installed on concrete pad with appropriate clearances, electrical conduit secured, and refrigerant lines in good condition. System operational with no deficiencies noted.

Completed MVP heating maintenance visit on 5-year-old Lennox furnace system. Performed comprehensive combustion analysis using digital analyzer, confirming unit operating at 77.3% efficiency with oxygen levels at 13.1% and zero CO detection. Inspected all HVAC components, ductwork connections, condensate drainage system, and verified proper operation of heating equipment.

Responded to service call for thermostat not maintaining set temperature following PCB replacement from previous week. Inspected outdoor unit electrical components and control board connections, verified proper wiring configuration and capacitor function. System evaluated and found operating within normal parameters with all electrical connections secure.

Converted existing three-way switch controlling living room outlet to constant power configuration and installed new ceiling fan circuit. Ran 3-wire switch leg from existing switch location through ceiling to center of room, cutting access through drywall as needed to route wiring. Installed fan-rated junction box at ceiling center for future customer installation of ceiling fan. In two upstairs bathrooms, removed existing outlets and standard boxes, then installed new single-gang old work boxes and wired customer-supplied GFCI receptacles. Made straight cuts in drywall where possible and secured cut pieces back in place where feasible.

Completed comprehensive annual maintenance and tune-up on one-year-old air conditioning system. Performed standard preventive maintenance procedures including inspection of air handler unit, verification of proper airflow through ductwork, examination of refrigerant lines, and testing of electrical components and controls. System operating within normal parameters with no deficiencies noted; unit confirmed in excellent working condition.

Completed MVP cooling maintenance visit on 13-year-old Lennox HVAC system. Performed standard preventive maintenance procedures on both indoor furnace unit located in basement and outdoor condenser unit. Outdoor condenser required vegetation clearance, as significant plant growth and weeds had encroached around the unit, partially obstructing airflow through the louvered vents. Cleared vegetation from perimeter of condenser to restore proper clearance and ensure adequate airflow for efficient operation. Inspected indoor furnace cabinet, PVC condensate drainage system, and associated ductwork connections. System operational at time of departure.

Installed soft start kit on HVAC system requiring upgraded electrical service. Replaced existing disconnect box with new 60-amp disconnect and dual-element time-delay fuses rated at 40A/250V AC to accommodate equipment specifications and ensure proper circuit protection.

Installed customer-supplied security cameras and flood lights at residential property. All fixtures were mounted, wired, and tested to ensure proper operation and coverage of the garage and exterior areas.

Performed comprehensive inspection of existing HVAC system for new homeowner requesting furnace evaluation and climate control assessment. Conducted thorough examination of outdoor condensing unit, including electrical components, wiring connections, capacitors, and control modules to verify proper operation and system integrity. Documented equipment condition with detailed photography of internal electrical compartment and external unit configuration for maintenance records.

Updated electrical service panel and installed three new dedicated circuits as requested. Ran exterior conduit and wiring from the main panel to support additional electrical loads. All electrical connections were properly terminated, conduits securely mounted to building exterior, and weatherproof enclosures installed at entry points to protect wiring from environmental exposure. System tested and verified operational upon completion.

Responded to service callback for water softener system experiencing slight leak at brine tank and salt level error message. Upon inspection, identified minor leak at brine tank connection and cleared erroneous salt level sensor reading. Verified system operation, confirmed leak repair, and reset error codes to restore proper function.