Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Performed courtesy second-look inspection of residential air conditioning system to verify previous estimate and assess system condition. Conducted comprehensive diagnostic testing including electrical measurements with digital multimeter and refrigerant pressure readings using manifold gauge set. Evaluated outdoor condensing unit operation, electrical components, and refrigerant charge levels. Documented system conditions with photographs for review. Provided technical findings to confirm accuracy of prior assessment and determine whether repair or full system replacement is most appropriate course of action.

Responded to follow-up service call for recently installed A/C system with inadequate cooling performance. Performed diagnostic testing using digital multimeter to check electrical readings at air handler unit, inspecting internal components including blower assembly, wiring connections, and control circuits. Accessed unit interior by removing insulation to thoroughly examine motor housing, electrical connections, and verify proper system operation following previous technician's work.

Performed routine preventive maintenance on residential standby generator unit. Completed oil change using 5W-30 motor oil, inspected unit for proper operation with system showing active standby status indicated by green power light, and assessed overall equipment condition noting minor exterior weathering and algae growth that does not affect functionality.

Completed routine maintenance and tune-up on HVAC system with no reported issues. Performed comprehensive inspection of furnace cabinet components including blower motor assembly, control board, capacitors, and all electrical connections. Verified proper operation of all system components, checked wiring integrity, and confirmed ventilation airflow through registers. System found to be in good working condition with all components functioning within normal parameters.

Responded to electrical hazard involving customer-installed ceiling fan causing breaker trips and visible sparking. Inspected electrical panel and service entrance area in basement to assess circuit loading and identify source of fault. Corrected unsafe wiring conditions to restore proper circuit protection and eliminate arcing hazard.

Completed diagnostic evaluation of residential tanked water heater system. Inspected water heater unit and surrounding plumbing infrastructure, noting moisture staining on concrete floor at base of tank and evidence of historical water damage on adjacent wall surfaces near valve assembly. Assessed expansion tank condition and plumbing connections at top of unit, including copper supply lines and flexible connectors. Evaluated red-handled valve assembly and associated PVC piping showing age-related wear and discoloration. Examined shower fixture for reported leak condition. Documented all findings with photos for customer review. Provided quote for expansion tank replacement as requested. System evaluation complete with recommendations for necessary repairs to address moisture issues and prevent further water damage.

Performed routine tanked water heater flush on residential unit installed in 2020. Drained sediment buildup from tank bottom, flushed system until discharge water ran clear, and refilled unit. Inspected anode rod condition, verified all inlet/outlet connections for leaks, and confirmed proper temperature and pressure relief valve operation. Unit operating within normal parameters with no issues identified.

Completed preventive maintenance service on residential air conditioning system. Inspected mechanical components, refrigerant lines, and utility connections in crawlspace area, noting age-related weathering on copper piping. Examined and documented air filter condition, which showed moderate dust accumulation within diamond-mesh filtration media.

Completed full HVAC system installation including new air handler and condensing unit. Evacuated refrigerant lines to proper vacuum levels using digital micron gauge, confirming system achieved below 500 microns for moisture removal. Verified electrical connections and replaced dual 35-amp time-delay fuses in outdoor disconnect, ensuring proper overcurrent protection for the new equipment.

Replaced failed compressor, dual capacitor, and contactor on outdoor condensing unit. Added acid neutralizer to system to protect new compressor from residual contaminants. Unit tested and operational upon completion.

Completed MVP cooling maintenance on residential HVAC system. Performed comprehensive inspection of air handler unit, blower assembly, and associated components including condensate drain lines, ductwork connections, and air filtration system. All equipment found operating within normal parameters with blower wheel showing typical light dust accumulation for seasonal use.

Replaced two exterior electrical outlets with weather-resistant GFCI receptacles, one located near the side entrance and another on the opposite side of the residence. Both installations included proper weatherproof covers and were tested to ensure ground fault protection functionality and compliance with outdoor electrical safety standards.

Responded to service call for multiple plumbing issues including garage faucet leak, malfunctioning toilet, and water heater concerns servicing the master bathroom. Inspected toilet tank and identified deteriorated internal components with significant mineral buildup and sediment accumulation on flush valve and fill valve assembly; flapper showed wear and discoloration from hard water deposits. Assessed water heater condition and examined associated plumbing connections and supply lines. Documented all findings with photographs for customer records and provided recommendations for necessary repairs including toilet tank component replacement to restore proper flushing operation.

Completed scheduled MVP cooling maintenance visit on 7-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, verified proper operation of all components, checked refrigerant lines and electrical connections, and ensured unit was operating within manufacturer specifications for optimal cooling performance.

Completed scheduled maintenance on 7-year-old air conditioning system. Inspection revealed significant corrosion on drainage components, which were documented and addressed. Performed standard maintenance procedures including examination of evaporator coil assembly, refrigerant line connections, and condensate system integrity to ensure proper cooling system operation.

Completed comprehensive AC tune-up on Blind and Sons outdoor condensing unit of unknown age with no reported operational issues. Performed standard maintenance protocol including system inspection, which revealed moderate dirt and debris accumulation on condenser coil fins and evaporator coil assembly with visible dust buildup and discoloration on heat transfer surfaces. Documented equipment condition through photographic evidence showing fin surface contamination and outdoor unit requiring cleaning attention for optimal heat exchange efficiency.

Completed scheduled MVP cooling maintenance visit on 5-year-old HVAC system. Performed load match verification on both indoor and outdoor units to confirm proper refrigerant charge and system operation. Inspected control board, wiring connections, and all electrical components inside air handler cabinet. Verified capacitor condition and all wire terminations at contactor assembly. Checked blower motor operation and confirmed all safety controls functioning properly. System operating within manufacturer specifications with no issues identified.

Responded to service call for exterior pole light replacement at residential property. Upon arrival, assessed existing exterior lighting fixtures including wall-mounted units on both the main building exterior and covered front porch area. Removed and replaced defective exterior pole light fixture with new unit. Verified proper electrical connections, tested operation of replacement fixture, and confirmed adequate illumination. All work completed in accordance with electrical code requirements for exterior lighting installations.

Completed MVP cooling maintenance visit on 5-year-old system that was rescheduled from previous appointment. Performed standard preventive maintenance inspection of indoor and outdoor HVAC components, including filter examination, refrigerant line connections check, and visual assessment of condensate drainage system. All equipment found operating within normal parameters with no immediate service needs identified.

Completed annual MVP cooling maintenance visit on 11-year-old residential HVAC system. Performed comprehensive inspection of furnace, air handler, and associated components including Aprilaire humidifier, ductwork connections, and condensate drainage system. All equipment photographed and documented, with unit found to be operating within normal parameters and no immediate service concerns identified.