Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Replaced two exterior switch boxes and converted an existing LB conduit body into a junction box at the point where Romex transitions to THHN conductors. Installed new conduit run from switch box to control box and pulled new THHN wire through the raceway to ensure code-compliant wiring methods for the HVAC electrical system.

Completed installation of customer-supplied garbage disposal unit under kitchen sink. Secured disposal to mounting assembly, connected discharge plumbing to existing PVC drain line, attached dishwasher drain hose with proper clamp, and wired electrical connections. Tested unit for proper operation, verified all connections for leaks, and confirmed system is functioning correctly.

Performed diagnostic evaluation and provided estimate for replacement of aging city pressure booster pump system, approximately 12-13 years old, located in utility area alongside water softener and water heater. Documented existing installation with copper piping connections showing typical age-related patina and corrosion, pump mounted on blue base platform with electrical connections and multiple plumbing ports requiring replacement due to equipment age and wear.

Completed second-phase air conditioning and evaporator coil installation in basement mechanical room. Installed new A/C unit with matching evaporator coil, connected flexible ductwork to existing return air system per specifications, and completed all refrigerant line sets, condensate drainage via PVC piping, and electrical connections. System tested and operating within manufacturer specifications.

Completed MVP cooling maintenance visit on residential HVAC system. Inspected furnace, air conditioning components, and control panel. Documented condition of capacitor showing rust accumulation on terminals and significant debris buildup throughout electrical compartment. Observed copper refrigerant lines, humidifier installation, and overall system configuration. Unit operational but showing signs of age and environmental exposure requiring monitoring.

Conducted on-site assessment for Mitsubishi mini split system installation in a 1,200 square foot residential garage with exposed wood framing and concrete flooring. Evaluated space layout, electrical requirements, and optimal placement for indoor and outdoor units to ensure adequate climate control for the two-bay structure. Documented site conditions and took measurements to provide accurate equipment sizing and installation estimate.

Completed routine cooling maintenance on two air conditioning systems (10-year-old and 2-year-old units). Inspected evaporator coils, noting debris accumulation on older unit's coil edges requiring attention. Verified refrigerant line connections, checked valve operations, and confirmed proper insulation on copper piping. Both systems operational and ready for continued service.

Completed comprehensive annual maintenance and tune-up on a one-year-old Lennox air conditioning system. Performed full inspection of outdoor condenser unit and indoor furnace components, verified refrigerant lines and electrical connections, checked system operation, and documented equipment condition with photographs. All components found to be in good working order with no issues identified during the maintenance visit.

Performed annual backflow prevention device testing on a 3/4" Wilkins Model 350 DCVA unit installed in basement. Conducted full diagnostic testing per state requirements, measuring differential pressure on both check valves and verifying proper operation of all components. Device passed all testing parameters with line pressure reading of 45 PSI and acceptable PSID values across check valve assemblies. Completed and filed official Backflow Prevention Device Test Report documentation with all required technical specifications and test results.

Completed preventive maintenance inspection on residential air conditioning system for MVP customer. Performed visual inspection of indoor air handler unit, verified proper filter access and housing integrity, and documented electrical control panel components including capacitor, contactor, and wiring connections in unit 35-E. All system components observed to be operational with normal wear patterns noted.

Responded to service call for 10-year-old Lennox air conditioning system running continuously without maintaining setpoint temperature and water leakage at equipment seam. Upon arrival, found significant water pooling on concrete floor surrounding HVAC unit, with moisture extending several feet from equipment base. Inspected condensate drainage system and identified clogged condensate line causing backup and overflow at drain pan seam. Cleared blockage from PVC condensate piping using appropriate tools and verified proper drainage flow. Tested condensate pump operation and confirmed pumping functionality restored. Cleaned drain pan and surrounding areas, checked refrigerant levels and airflow parameters. System now cycling properly, maintaining temperature setpoint, and draining condensate without leakage.

Conducted comprehensive assessment of existing HVAC system for furnace replacement estimate. Customer expressed interest in upgrading to a two-stage furnace system to improve heating efficiency and comfort control. Evaluated current Carrier Infinity 80 series furnace installation in mechanical room, documenting existing equipment configuration including ductwork connections, venting system with PVC exhaust piping, electrical connections, and air handler setup. Assessed exterior condensing unit placement on concrete pad with proper clearances and drainage. Photographed complete system layout including indoor furnace unit, associated plumbing connections, electrical components, and outdoor AC unit to provide accurate replacement specifications and equipment sizing recommendations for two-stage furnace upgrade proposal.

Completed preventive maintenance cooling visit on 7-year-old residential air conditioning system. Performed comprehensive system diagnostics including refrigerant pressure testing, electrical measurements, and operational verification of all components. Unit operating within normal parameters upon completion of service.

Completed comprehensive tune-up on 13-year-old air conditioning system with heavily soiled evaporator coils showing significant dust, lint, and debris accumulation restricting airflow. Performed standard maintenance protocol including system inspection, cleaning, and operational testing of dual outdoor condenser units, and provided complimentary carbon monoxide detector installation.

Completed preventive maintenance tune-up on 15-year-old outdoor air conditioning unit. Inspected electrical connections in control panel, noting visible corrosion on capacitor terminals and wire connections that were cleaned and tightened. Removed accumulated debris from electrical compartment, checked all wire terminations for secure connections, and verified proper operation of all system components despite age-related wear and environmental exposure.

# HVAC Install - Complete System Completed full residential HVAC system installation including 90% AFUE furnace and matching air conditioning condenser unit. Installed furnace in basement utility area on concrete pad with proper clearances, connected white PVC intake and exhaust venting through foundation, and integrated unit with existing ductwork using metal supply plenum. Mounted outdoor AC condenser on concrete paver base with level positioning, ran refrigerant lines and electrical conduit along exterior siding to disconnect box, and completed all electrical connections per code requirements. Tested system operation, verified proper airflow, and confirmed heating and cooling cycles functioning correctly.

Installed dedicated electrical outlet in garage for vertical platform lift (VPL). Ran conduit and wiring to provide power supply, ensuring proper circuit protection and code compliance for wheelchair accessibility equipment operation.

Responded to service call for malfunctioning hose bib at 20-year-old residential property. Upon inspection, assessed the exterior water spigot condition and functionality, identifying issues related to the aging fixture. Completed necessary repairs to restore proper operation of the outdoor hose bib, ensuring adequate water flow and eliminating leaks at the connection point.

Replaced existing 59-gallon Bradford White power vent water heater with new 50-gallon Bradford White power vent unit (Model RG1PV50S6N1) featuring 6-year manufacturer warranty. Installation included replacement of expansion tank, upgrade from aluminum drain pan to lifted plastic pan with connection to existing PVC drain line, and integration with existing copper supply lines and PVC venting system. All components staged and installed per manufacturer specifications with proper clearances and code compliance.

Completed routine MVP cooling maintenance visit. Inspected and tested system control board and verified proper electrical connections at terminal block, ensuring all wiring configurations were secure and functioning correctly. System operating within normal parameters.