Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Responded to service call for 3-year-old LG mini split system experiencing water leakage. Inspected wall-mounted indoor unit and accessed attic space above to examine condensate drain line routing and connections. Identified drainage issue, cleared blockage from condensate line, verified proper pitch and flow, and tested system operation to confirm leak was resolved.

Performed routine inspection on 10+ year old air conditioning system following customer concern about debris accumulation around outdoor unit. Verified all HVAC equipment operational status, inspected American Standard furnace and associated condensate drainage system for proper function. Cleared debris from around AC unit and confirmed system safety and performance parameters were within acceptable ranges.

Performed tankless water heater descaling service using chemical flush procedure. Connected circulation pump and descaling solution container to unit's isolation valves, ran cleaning solution through heat exchanger for proper deliming treatment to remove mineral buildup and restore optimal performance.

Responded to no cooling call on residential air conditioning system. Upon arrival, performed diagnostic testing on outdoor condensing unit. Used digital multimeter to test dual run capacitor, which showed failure and was unable to hold proper charge. Capacitor failure prevented compressor from starting, resulting in complete loss of cooling. Explained findings to customer and provided options for repair. Testing confirmed all other electrical components and connections were intact with no additional issues identified.

Conducted on-site evaluation for heat pump installation to supplement existing gas furnace as backup heating source. Assessed current Trane condensing unit location, electrical requirements, and compatibility with dual-fuel configuration for seamless integration between heat pump and gas furnace systems.

Replaced Delta cartridge, seats, and springs on bathtub and shower faucet assembly. Ordered necessary parts including Delta RP4993 and RP74236, which were received and installed to restore proper function to the chrome cross-handle shower valve.

Provided free estimate for water heater and water softener replacement at residential property. Inspected existing 50-gallon Bradford White automatic storage natural gas water heater and associated plumbing system installed in basement utility area. Evaluated hydronic system configuration including white expansion tank, circulation pump with motor assembly, copper supply lines with brass fittings, PVC drainage piping, and pressure regulation components. Documented leaking water softener unit requiring replacement. Assessed current installation setup mounted against concrete block wall, noting copper and PVC pipe routing, electrical connections to pump assembly, and red-labeled valve positioning. Photographed equipment specifications including BTU rating, capacity, and clearance requirements for replacement planning purposes. Reviewed system functionality and provided comprehensive estimate for complete water heater and water softener replacement to address existing leak condition and u

Replaced deteriorated galvanized piping with new copper piping in crawl space and basement utility area. Removed heavily corroded shutoff valves and fittings exhibiting significant oxidation and rust damage at floor-wall junction, installed new copper pipe runs and brass fittings to restore proper water supply functionality and prevent future leaks from corroded connections.

Conducted on-site assessment for heat pump system replacement at residential property. Evaluated existing 14-year-old heat pump system including thermostat operation, air handler controls, ductwork condition, and refrigerant line routing in attic space. Documented current system configuration and provided replacement estimate for new heat pump installation.

Completed MVP cooling maintenance visit on 5-year-old system. Performed comprehensive inspection of outdoor unit electrical connections, including contactor terminals, wire terminations, and control wiring. All electrical connections were found secure with proper wire color coding intact across multiple circuits. System operating within normal parameters.

Completed full HVAC system installation including 80% efficiency furnace, air conditioning condenser unit, and hot water heater. The Bryant furnace was installed in the basement utility room with proper venting and ductwork connections, while the outdoor condenser unit was positioned on a concrete pad against the building exterior with appropriate electrical connections and conduit routing. All equipment was tested for proper operation, refrigerant lines were charged and sealed, and the system was commissioned to ensure optimal performance and efficiency.

Completed installation of 80% AFUE gas furnace and air conditioning system. Installed new fuse block with proper amperage fuses and verified all electrical connections with appropriate wire gauging. Mounted and tested Kidde carbon monoxide alarm to ensure proper operation and safety compliance for new heating system installation.

# HVAC Maintenance - Cooling Completed MVP recurring maintenance visit on a 4-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including examination of cabinet panels, protective grilles, and fan assembly. Unit showed normal operational wear with accumulated dirt, dust, and environmental debris on exterior surfaces and coil fins. Condenser positioned on concrete pad with adequate clearance; noted minor vegetation growth near base and organic debris accumulation on pad surface. Fan motor and blade assembly inspected and found to be operational. Documented current condition of unit exterior panels showing weathering and soiling consistent with outdoor installation. All major components visually assessed for proper operation and structural integrity.

Installed two new electrical outlets in residential garage per customer request. Ran appropriate wiring, mounted outlet boxes, and verified proper grounding and circuit protection. All work completed to code with outlets tested and fully operational.

Completed comprehensive electrical upgrade in 60-year-old ranch home, replacing obsolete cloth Romex wiring with modern NM cable throughout three rooms. Installed new circuit breakers in existing panel to accommodate updated circuits, ensuring proper load distribution and code compliance. All connections were tested and verified operational, with panel properly labeled for future reference.

Completed MVP recurring cooling maintenance visit on 7-year-old system. Performed comprehensive inspection of outdoor condensing unit, including examination of blower wheel assembly which showed moderate dust and debris accumulation on fins and blades. Inspected electrical components including dual-run capacitor, contactor, and associated wiring connections. All components found to be operational with wiring properly secured and terminals intact. Unit operating within normal parameters at time of service.

Completed scheduled MVP cooling maintenance visit on HVAC system. Performed comprehensive inspection of condenser fan assembly, verifying proper blade alignment, clearances, and operational integrity. Accessed electrical control compartment and inspected circuit boards, capacitor, wiring connections, and control components for proper function and signs of wear. All system components found operating within normal parameters with no immediate service needs identified.

Completed full HVAC system installation including 90% efficiency furnace, 2.5-ton air conditioning unit, and new flue venting system while reusing existing zoning controls. Performed system evacuation and verified proper vacuum levels using digital micron gauge, confirming system integrity at 242 microns before refrigerant charging. Installed and tested Kidde carbon monoxide alarm to ensure proper safety monitoring for combustion appliances.

Completed installation of 80% efficiency furnace and air conditioning system in residential basement utility area. New furnace unit installed with proper venting and ductwork connections, including rectangular supply plenum and horizontal distribution runs. AC system integrated with furnace for complete HVAC solution, ensuring proper refrigerant lines and condensate drainage. All equipment secured per manufacturer specifications, electrical connections completed, and system tested for proper operation and airflow distribution throughout the home.

Completed MVP cooling maintenance visit on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit and indoor blower assembly, including visual examination of compressor, refrigerant lines, electrical connections, and squirrel cage blower wheel. Documented system condition with photos showing all major components operating within normal parameters.