Trusted HVAC, Plumbing & Electrical Services in Medina, OH

Responded to service call for malfunctioning sump pump located at the base of elevator shaft. Upon arrival, found standing water in the pump basin and surrounding floor area. Inspected sump pump system, including basin, discharge piping, and electrical connections. Identified pump failure preventing proper water removal from the pit. Assessed PVC discharge line routing and verified proper venting. Documented existing water damage and moisture staining on concrete floor surfaces. Photographed pump installation, piping configuration, and overall site conditions for record. Provided recommendations for pump replacement and potential improvements to drainage system to prevent future water accumulation in this utility area.

Completed MVP cooling maintenance visit on 20-year-old HVAC system. Upon inspection, found extensive dust and debris accumulation throughout air handler interior, including heavy buildup on evaporator coil assembly showing signs of corrosion and deterioration. Blower wheel exhibited significant dirt accumulation on blades and housing, with visible rust on central motor mounting hub. Cleaned and serviced unit components, removing debris from base pan and serpentine refrigerant lines. Documented pre-service condition showing need for continued maintenance on aging equipment.

Completed follow-up work to address incomplete patching from previous panel replacement service. Filled and finished exterior hole in siding where electrical conduit penetrates building envelope, ensuring proper seal and restoration of wall surface. Verified all three previously installed panels (garage, laundry room area, and upstairs location) are functioning correctly and installation meets code requirements.

Completed comprehensive tune-up on 7-year-old residential air conditioning system. Performed thorough inspection of outdoor condenser unit, noting significant debris accumulation within fin coil assembly requiring attention. Assessed electrical control panel and wiring connections, documenting existing installation condition. All critical components evaluated for proper operation and seasonal readiness.

Installed two new dedicated electrical outlets in the garage on a shared circuit breaker from the main panel. Routed electrical wiring from the crawl space through the garage and into the attic space to reach the outlet location on the right wall, with surface-mounted conduit used for the final vertical run where concealed wiring was not feasible. One outlet was positioned to serve a freezer unit, while the second outlet was installed on the opposite wall to provide additional power access in the workspace.

Conducted site assessment for mini split installation in new addition space currently under construction. Evaluated framing structure, existing electrical rough-in, and ventilation requirements to determine optimal equipment placement and line set routing for climate control system serving the workspace area.

Completed MVP recurring cooling maintenance on two HVAC units. During inspection, discovered active water leakage from condensate drain line with visible pooling on floor beneath horizontal PVC piping section. Addressed drainage issue, inspected condensate trap and drain line connections, verified proper operation of both systems, and confirmed all electrical components and controls functioning correctly.

Completed MVP air conditioning maintenance service. Upon arrival, diagnosed and replaced failed TR30R time-delay fuses in the outdoor unit's electrical disconnect. Verified proper voltage and amperage readings using digital multimeter to ensure system electrical components were functioning within manufacturer specifications. Unit tested and confirmed operational.

Responded to service call for multiple toilet issues at facility. Assessed one non-functioning toilet with drainage concerns and inspected drain line for blockages or restrictions. Evaluated internal flush mechanisms on three to four additional toilets requiring component replacement. Removed tank lids to examine fill valves, flappers, flush valves, and float assemblies. Documented existing conditions including worn internal components affecting proper flushing operation. Photographed toilet installations showing accessibility grab bar configurations and measured clearances for proper fixture positioning. Identified deteriorated flush valve seals and aging fill valve assemblies requiring replacement to restore proper water flow and flushing performance.

Conducted on-site evaluation for HVAC system replacement to provide alternative heating solution to existing baseboard system. Assessed electrical panel capacity and existing infrastructure, documented current living space layout and conditions to determine optimal equipment placement and sizing requirements for comprehensive heating system options.

Responded to report of water leak in garage ceiling suspected to originate from dishwasher above. Upon inspection, identified active water staining and moisture intrusion on ceiling surface with visible brownish discoloration indicating ongoing or recent leak. Documented damage through photographic evidence showing extent of water penetration and affected ceiling area. Scheduled follow-up appointment to perform further diagnostic assessment and determine exact source of leak, whether from dishwasher supply line, drain connection, or other plumbing fixture above affected area.

Responded to service call regarding faulty breaker on exterior electrical setup between house and barn. Accessed electrical disconnect box mounted on white conduit in utility space, inspected the installation and wiring connections, and replaced the defective breaker. Verified proper operation of disconnect switch with red safety handle and confirmed secure mounting to structural framing. System tested and restored to full functionality.

Completed preventive maintenance visit on 6-year-old Lennox furnace system with outdoor condensing unit model CR33-24B-F. Performed comprehensive inspection of indoor air handler and outdoor condenser, verified refrigerant charge and system pressures within manufacturer specifications for R-410A operation. Inspected electrical connections, tested capacitor performance, and confirmed proper airflow through evaporator coil. Checked condensate drain lines for proper drainage and cleared PVC drain system. Verified thermostat operation and system cycling. All components operating within normal parameters with no deficiencies noted at time of service.

Completed comprehensive water line replacement beginning at the outlet side of the water meter. Removed and replaced deteriorated galvanized and polybutylene water lines that were previously feeding the water heater and laundry area. Installed new PEX-A piping system with proper fittings, connecting from the water meter through to existing CPVC lines and copper pipes above the water heater. Replaced outside faucet with new frost-free hydrant and installed dedicated shut-off valve. Added main shut-off valve on house side of water meter for improved system control. Replaced deck-mount laundry faucet with new fixture, complete with proper shut-off valves and supply lines. Transitioned connections between existing CPVC water lines and new PEX-A system above water heater using appropriate fittings and connections. All work performed to code specifications. Removed all obsolete galvanized pipe, polybutylene materials, and associated fittings from property. Disposed of all debris and left

Replaced defective condensate drain alarm with new Sure Switch unit on existing PVC drain line configuration. Unit was installed using truck stock inventory and tested for proper operation to ensure reliable overflow detection and system protection.

Conducted comprehensive electrical estimate for backup generator installation at residential property. Assessed existing electrical infrastructure including main service panel, circuit breaker configuration, and utility space layout to determine optimal integration point for generator transfer switch. Documented current electrical distribution system featuring dual-column breaker arrangement in main panel, existing gas piping with shutoff valves in basement ceiling area, and available mounting locations for required equipment. Evaluated structural considerations including OSB ceiling construction, existing HVAC ductwork placement, and PVC drainage routing to identify clear pathways for generator feeder cables and outdoor equipment placement. Photographed electrical panel specifications and basement utility infrastructure to support equipment sizing recommendations and installation planning.

Provided comprehensive estimate for complete furnace and air conditioning system replacement at residential property. Evaluated existing American Standard furnace installation in basement utility area, assessed current PVC venting configuration, and documented existing equipment specifications to determine appropriate replacement options for both heating and cooling systems.

Responded to callback for humidity concerns following recent system installation. Performed diagnostic testing on outdoor condensing unit and verified system operation. Unit assessed under warranty coverage, all electrical connections checked and system parameters evaluated to address reported indoor humidity levels requiring potential adjustment.

Responded to service call for 19-year-old Lennox air conditioning condenser unit producing excessive noise. Upon inspection, identified failed dual run capacitor exhibiting severe corrosion, rust deterioration on terminal connections, and turquoise-colored copper oxidation buildup around wire terminals. Replaced defective capacitor with new unit, verified proper electrical connections, and tested system operation. Unit now running quietly with normal operating parameters restored.

Responded to service call for two AC units, with one unit producing loud banging noise upon startup. Inspected outdoor condensing unit and internal electrical components. Examined capacitor assembly, wiring connections, and associated electrical terminals. Capacitor showed signs of weathering consistent with outdoor installation but appeared operational. Verified proper wire connections at capacitor terminals and wire nut junctions. Documented unit condition and component configuration with photographs for service records.