Your Trusted HVAC, Plumbing & Electrical Experts in Wadsworth, OH

Completed routine MVP cooling maintenance visit on residential air conditioning system. Upon inspection, found outdoor condenser unit with significant dirt and debris accumulation on heat exchanger coil fins and filter surfaces, which can restrict airflow and reduce system efficiency. Unit exterior showed normal weathering consistent with outdoor exposure, with mulch and organic debris present around base. Condenser fan grille and motor housing appeared operational, and unit was properly positioned on concrete pad with adequate clearance from building structure.

# Electrical Service - Generator Gas Line Maintenance Responded to follow-up service call for previously installed generator system where the black pipe gas line had not been painted during initial installation. Upon arrival, confirmed visible rust formation on exposed metal gas piping and fittings mounted on exterior wall. Prepared and painted all unpainted black pipe gas line components using appropriate rust-inhibiting paint suitable for gas line applications. Ensured proper coverage of all pipe sections, T-joints, elbow fittings, and connection points to prevent further oxidation and corrosion. Verified electrical connections to generator remained secure and operational per manufacturer specifications. All work completed in accordance with local codes and safety standards for exterior gas line installations.

Responded to no cooling complaint with thermostat displaying flashing "cool on" indicator and 7-degree temperature differential. Diagnosed failed contactor on outdoor condensing unit preventing compressor and condenser fan operation. Replaced defective contactor with new component, restored power, and verified proper system operation with normal cooling cycle achieved.

# Kitchen Sink Plumbing Leak Repair Responded to service call for leaking kitchen sink piping near the dishwasher valve connection. Upon arrival, conducted diagnostic inspection of the under-sink plumbing system and identified active water leak at the dishwasher supply valve assembly. Water damage was evident on the cabinet floor substrate, with visible staining and moisture accumulation indicating ongoing leak condition. Inspected all supply lines, drain connections, and valve assemblies in the affected area. The metal valve assembly showed signs of corrosion and deterioration, which was determined to be the source of the leak. Performed necessary repairs to the dishwasher valve connection, addressing the leak at the point of failure. Tested all connections under pressure to verify proper seal and confirm no additional leaks were present. Inspected adjacent plumbing components including flexible supply lines and mounting hardware to ensure system integrity. Documented conditions

Removed existing water heater and installed new Bradford White 8-year warranty unit with complete system integration. Replaced thermal expansion tank to ensure proper pressure regulation and system safety. All existing plumbing connections, gas lines, temperature and pressure relief valve, and copper piping were verified to meet current code requirements upon completion of installation.

Responded to no cooling complaint on recently installed air conditioning system that was also producing abnormal noises. Upon arrival, unit was shut down by customer. Performed diagnostic testing using refrigerant manifold gauges and clamp meter to assess system operation and electrical components. Inspected capacitor, contactor, and associated wiring connections within outdoor unit. Measured system temperatures and pressures, with readings indicating superheat and subcooling values of 240.1°F and 238°F respectively during testing phase. Verified proper electrical connections to capacitor and contactor assembly, checked for loose wiring or failed components that could cause unusual sounds. System evaluated under MVP membership, no additional treatment authorized at this time.

Responded to service call for annual backflow prevention device testing as required by municipal code. Located backflow preventer assembly installed in interior wall cavity of 2008-built single-family residence. Performed complete inspection and testing of the reduced pressure zone (RPZ) assembly, including check valves, relief valve, and test cocks. Device was found to be functioning within acceptable parameters and maintaining proper differential pressure. Documented installation location with photographs for customer records and completed required certification paperwork for city compliance filing.

Completed scheduled MVP cooling and heating maintenance visit. Performed comprehensive system inspection of furnace and air handling unit, including internal component evaluation with access panel removal. Conducted diagnostic testing using calibrated instruments, verified proper operation of all mechanical systems, inspected ductwork connections and PVC condensate drainage lines, and documented equipment condition through photographic records. All systems found operating within normal parameters with no immediate service needs identified.

Installed a new 1 1/2" gas main from the exterior meter location under the porch to the interior of the home, establishing supply infrastructure for multiple appliances. Ran gas line to range top with shutoff valve and flex connector installation at kitchen location. Installed 1" gas line under porch extending to rear of property, trenched underground from porch to detached garage/barn structure, then ran line vertically up exterior wall and through attic space to opposite end of building for future heating system connection. Configured multiple future tap points under porch for water heater, furnace, oven, floor heating system, pool heater, and outdoor grill. Completed all pipe fitting installations including reducers, 90-degree elbows, and necessary connections using galvanized materials. All work performed to code specifications with proper meter integration and pressure regulation components in place.

Completed warranty replacement of water softener tank in residential utility room. Installed new Impressions brand softener unit with digital control head, connected all plumbing lines and verified proper operation. Documented existing equipment with photographs of tank, control head, and serial number for warranty processing, and retained old tank on-site per warranty return protocol.

Completed MVP cooling maintenance visit during scheduled 1-5pm service window. Performed routine system inspection and diagnostics, including temperature measurements of HVAC equipment which registered 42.4 degrees on digital instrumentation. Inspected and assessed air filtration components, documenting condition of return air grilles and filters for maintenance records.

Installed new Woodford frost-free outdoor faucet with ball valve shutoff for exterior water access. Replaced existing toilet in master bathroom and installed new toilet in second floor hall bathroom, including removal of old fixtures, preparation of toilet flanges, installation of new wax rings, and connection of water supply lines. All fixtures tested for proper operation and checked for leaks upon completion.

Responded to emergency water leak affecting hot water system. Upon arrival, confirmed hot water supply had been shut off as a precautionary measure to prevent further water damage. Conducted thorough inspection of copper piping loop configuration, expansion tank, and associated plumbing components in utility area. Identified source of leak in hot water distribution system. Assessed solder joints and fittings throughout the copper pipe assembly for integrity. Documented existing mechanical system installation including expansion tank, pressure vessel, and interconnected piping for service records. System evaluated and leak addressed to restore safe operation of hot water supply.

Installed electrical conduit from main service panel to above-ground pool equipment area to replace temporary extension cord setup. Ran weatherproof conduit along exterior of residence, terminating at dedicated pool equipment disconnect near filter and pump system positioned adjacent to pool on gravel pad.

Completed installation of 18kW Generac whole home generator system with 100-amp automatic transfer switch. Ran 30 feet of gas line and electrical conduit from main service panel to generator location on exterior concrete pad. Coordinated utility disconnect with power company, installed weatherproof disconnect box, and mounted transfer switch in accordance with local electrical codes and manufacturer specifications.

Responded to water leak in basement with no water availability during business hours. Upon inspection, identified active water damage on ceiling and walls with visible brown discoloration, peeling paint, and moisture infiltration at wall-floor junction. Documented extensive water staining along baseboards and deterioration of wall materials with cracking and flaking present. Located flexible supply line with connector valve running along affected area. Photographed damage extent showing compromised structural finishes on oak hardwood flooring and drywall surfaces for assessment and repair planning.

Completed scheduled MVP cooling maintenance visit on outdoor condensing unit. Upon arrival, observed significant dirt and debris accumulation on mesh filter screens affecting airflow efficiency. Performed comprehensive system inspection, cleaned condenser coils and protective screens, verified proper operation of all mechanical components, and ensured adequate clearance around unit. System restored to optimal operating condition with improved airflow through cleaned filters.

Completed BS-MVP cooling maintenance visit on 9-year-old Lennox air conditioning system. Performed comprehensive inspection of outdoor condenser unit, checked electrical connections, verified proper airflow through coil fins and louvers, and ensured unit operational parameters met manufacturer specifications. System found operating within normal range with no immediate service needs identified.

Completed scheduled cooling maintenance visit on HVAC system. Inspected air filter showing moderate dust accumulation with visible discoloration across mesh surface, and examined blower wheel assembly which displayed significant dust and debris buildup on metal blades and housing. System components photographed and documented for maintenance records.

Completed preventive maintenance tune-up on 8-year-old Lennox air conditioning system. Inspected outdoor condenser unit, verified proper operation of all components, and checked electrical connections at disconnect box. Accessed indoor air handler and inspected blower assembly, noting moderate dust and lint accumulation on squirrel cage blower wheel fins that could impact airflow efficiency. Evaluated ductwork system for potential cleaning needs based on visible debris in blower compartment.