Trusted HVAC, Plumbing & Electrical Services in Alliance, OH

Performed on-site evaluation of a 15-year-old Rinnai tankless water heater to provide replacement estimate. Inspected unit's internal components including heat exchanger, gas valve assembly, ignition system, and control board displaying operational temperature of 120°F. Documented current condition of copper water lines, gas connections, and venting system through detailed photography for replacement planning and customer consultation.

Replaced failed boiler expansion tank due to heavily corroded pipe fitting and compromised system integrity. Removed old tank with rusted connections and installed new cylindrical expansion tank with proper fittings to restore system pressure control and prevent future boiler damage. System tested and confirmed operational upon completion.

Responded to basement flooding caused by failed sewer stack fitting beneath concrete floor. Jackhammered basement floor around the sewer stack to access the compromised fitting at the concrete penetration point. Removed damaged fitting and installed new connection, tying back into the existing ABS drain line above the concrete. Completed concrete excavation, pipe replacement, and reconnection to restore proper drainage and prevent further water intrusion.

Conducted on-site assessment for stand-alone dehumidifier installation in unfinished basement utility area with existing HVAC equipment. Evaluated space conditions, structural considerations, and optimal placement for dehumidifier unit to address indoor air quality concerns in below-grade living space.

Completed annual maintenance on 10-year-old hydronic boiler system. Performed visual inspection of electrical components, control board, contactors, and pressure controls within cabinet; all components functioning within normal parameters. Inspected expansion tank, circulator connections, and associated copper piping; noted minor rust staining on valve assembly but no active leaks detected. System tested and operating properly.

Responded to callback for damage assessment and repair related to previous installation work. Upon arrival, inspected electrical service equipment at exterior meter location and documented existing installation condition. Investigated reported issue with refrigerator circuit and structural joist that was inadvertently damaged during prior electrical installation. Assessed interior wall outlet location and surrounding area where damage occurred. Documented both exterior service panel configuration and interior affected area with photographs for records and potential repair coordination.

Responded to service call for leaking well pressure tank in basement. Upon arrival, coordinated timing with customer to provide required advance notice. Inspected blue pressure tank system and identified active leak at tank connection points. Assessed complete well water system including pressure tank, pump assembly, brass manifold fittings, shut-off valves, pressure gauge, and associated copper and PVC piping. Diagnosed leak source and performed necessary repairs to pressure tank connections and plumbing assembly. Verified all brass fittings, valve connections, and pipe joints for proper seal integrity. Tested system pressure and monitored for any additional leaks. Confirmed pump operation and pressure tank functionality after repairs were completed. Left work area clean and system fully operational.

Diagnosed and resolved banging noise caused by flexing plenum requiring disassembly and creasing of ductwork to add structural rigidity. Identified failed duct booster that was impeding airflow to two upstairs bedrooms sharing a common duct run. Ductwork had been previously reduced in size to accommodate newer furnace installation. Replaced failed duct booster, creased plenum to eliminate flexing, and repaired shared duct run to restore proper airflow distribution to affected bedrooms.

Responded to emergency call for main drain line blockage causing extensive water backup and flooding in basement area. Successfully cleared main drain line obstruction, restoring proper drainage flow and eliminating sewage backup affecting concrete floor surfaces near doorway threshold and utility room space.

Completed HVAC system evaluation for non-cooling air conditioning unit. Assessed aged outdoor condenser unit showing significant wear and weathering, along with indoor furnace equipment in basement mechanical room. Provided comprehensive replacement estimate for complete system upgrade due to equipment age and condition.

Completed preventative maintenance tune-up on 9-year-old gas furnace system. Performed comprehensive inspection of heating unit, including examination of control board, electrical connections, and safety systems. All components found to be operating within normal parameters, with wiring and control systems functioning properly.

Inspected and assessed corroded washer hookup valves and associated plumbing prior to new appliance installation. Found frozen shut-off valve with significant corrosion and green patina on brass components, causing minor drip when operated. Documented extensive deterioration on metal piping including surface rust and oxidation on horizontal supply lines. Identified mixed-age plumbing system with newer PVC and blue plastic piping connected to older corroded metal components. Photographed valve assemblies, pipe conditions, and wall-mounted fixtures showing rust staining and water damage on surrounding surfaces for customer review and repair recommendations.

Completed preventive maintenance cooling visit on 7-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including visual assessment of cabinet condition, protective grilles, and fan assembly. Unit found to be in serviceable condition with normal signs of outdoor exposure. All components accessible and operational during routine maintenance procedures.

Replaced outdated stairway ceiling light fixture with new motion sensor-activated fixture in older residential property. Addressed safety concerns by securing deteriorated wire insulation and working with legacy wiring system that lacked modern electrical box infrastructure. Successfully installed recessed LED fixture with motion detection capability, ensuring proper electrical connections and code-compliant mounting despite non-standard ceiling configuration.

Replaced multiple electrical outlets throughout the residence, including installations in rooms with decorative wall finishes and living areas. All outlet replacements were completed to code specifications, ensuring proper grounding and secure mounting in existing junction boxes.

Conducted on-site assessment of existing residential water heater installation in basement utility area. Documented current unit condition, noting significant age-related deterioration including rust staining at tank base and general wear on exterior surfaces. Evaluated existing plumbing connections, including copper supply lines, brass shutoff valves, and pressure regulation equipment. Photographed water heater specifications, electrical connections, and mechanical infrastructure to determine replacement requirements. Assessed utility room layout, clearances, and access points for future water heater replacement installation.

Completed routine maintenance on residential air conditioning system for new homeowners. Performed system inspection including examination of air handler unit, electrical control panel, and associated components. Verified proper operation of blower motor, contactors, and control circuitry; all equipment found to be functioning within normal parameters at time of service.

Completed comprehensive whole home plumbing inspection for recently purchased residence, including evaluation of hot water tank of unknown age. Documented existing plumbing infrastructure including under-sink drain trap with visible mineral buildup at connections, rigid metal supply lines, and flexible braided supply hose. Assessed basement utility area plumbing systems including PEX water lines, PVC drainage piping, and metallic piping with evidence of corrosion staining at ceiling penetrations. All accessible plumbing components photographed and evaluated for condition and compliance.

Responded to service call for 9-year-old furnace with reported slamming damper noise in ductwork system. Upon inspection of the HVAC infrastructure, examined the flexible metallic ductwork, main supply ducts, and air handler connections throughout the basement area. Investigated potential sources of noise including loose duct strapping, unsecured flexible duct sections, and vibration points where ductwork interfaces with the furnace unit. Documented existing conditions of the galvanized metal ductwork and air distribution system for customer records.

Replaced 22-year-old 40-gallon electric water heater with new 40-gallon short electric unit featuring 6-year manufacturer warranty. Updated corroded cold water shut off valve and installed thermal expansion tank. Removed existing ball valve on hot water side of water heater. Installed new 3/4-inch shut off valve on house side of water meter. Replaced two shut off valves under second floor lavatory that isolate tub and lavatory fixtures with new ball valves, including necessary pipe and couplings to complete installation.