Heating, Air Conditioning, Electric & Plumbing Services in Cleveland, OH

Performed seasonal maintenance on a 9-year-old gas furnace, including inspection of the return air filter, which showed moderate loading and was serviced to restore proper airflow. Inspected the interior components, including the inducer/blower motor, gas valve assembly, pressure switch, and wiring harness, finding all connections intact with only light dust accumulation and no signs of rust, corrosion, or damage. The unit was left in good working condition.

Installed a customer-supplied matte black tub spout, reworking the supply piping to eliminate the existing push-to-connect (SharkBite) fitting and replace it with a permanent copper stub-out connection secured to the wall framing. Restored the tub spout to proper position against the tile wall, confirming a secure, leak-free connection and correct water flow from the valve.

Performed an on-site assessment for an electrical panel upgrade to 100A or 200A service, measuring the panel location and clearances to determine suitability for the larger service. Evaluated the existing garage electrical circuits and noted that rewiring may be required, and documented the exterior service area to plan the upgrade scope.

Investigated reported water leak and ceiling discoloration in the dining room, locating moisture staining at the wall-ceiling junction consistent with an intermittent leak from the plumbing above. Replaced the failed section of piping with a new flexible rubber elbow coupling joining two PVC pipe segments, secured with stainless steel worm-gear hose clamps, restoring a watertight connection.

Responded to a warranty return for recurring failure of the plastic mounting straps securing the flexible gas line on the Generac 18KW standby generator. Inspected the line routing along the fence and replaced the failed plastic straps and clips with metal mounting straps, ensuring the line is properly supported and not over-tightened. Verified all connections and supports were secure, with no further strain on the line.

Performed scheduled furnace maintenance on a natural gas heating system, including a combustion analysis using a Bacharach analyzer. Readings confirmed efficient, safe operation, with CO at 24 ppm, efficiency at 95.4%, CO2 at 8.5%, O2 at 5.9%, and a stack temperature of 106°F. System was left operating within normal parameters.

Responded to a recurring furnace noise complaint and inspected the unit, including the sheet-metal ductwork and panel areas and the associated wiring connections. Performed a combustion analysis on the natural gas furnace, recording O2 at 9.9%, CO at 23 ppm, CO2 at 6.2%, and 82.7% efficiency, to verify safe and proper operation.

Responded to a no-heat/no-cooling call on a furnace with a previously installed control board. Inspected the thermostat wiring at the base plate, verifying the R, W, Y, and G terminal connections and tightening the screw terminals. Located a blown 3-amp automotive blade fuse on the control board, which had interrupted the 24V control circuit, and replaced it to restore thermostat communication with the unit.

Responded to a noise complaint on a Lennox SL280UH090V36BK gas furnace and inspected the unit, including the blower, burner compartment, gas valve, and flue connections. Verified gas manifold pressure with a digital manometer at the gas valve test port to confirm proper combustion operation as part of diagnosing the startup noise.

Completed a full HVAC system installation, including a new outdoor heat pump/condenser unit charged with R-454B refrigerant, with insulated suction line and bare liquid line connected at the brass service valves. Installed galvanized supply and return ductwork with foil-faced tape sealing at the seams, and connected the gas supply with a black iron pipe run, brass shutoff valve, and corrugated stainless steel flex connector. Visual inspection showed no signs of leaks, corrosion, or damage on the refrigerant lines, gas piping, or ductwork.

Inspected the furnace exhaust venting following a recent PCB installation and found a gurgling noise at the PVC exhaust pipe, with moisture and residue visible inside the open pipe end, indicating condensate accumulation in the vent line. Checked the condensate drain, trap, and tubing routing, and evaluated the evaporator coil as requested to confirm proper drainage and operation.

Responded to a complaint of a thermostat repeatedly detaching from the wall and inspected the wall plate and terminal block. Found an empty mounting screw hole on the right side of the plate, leaving the thermostat without a secure attachment point; the existing low-voltage wiring (R, W, G, Y, C) was intact on the terminal block. Remounted and secured the wall plate and thermostat, and verified it remains firmly seated on the wall.

Inspected natural gas furnace for reported flue/venting deficiency and found heavy rust and corrosion on the cabinet floor pan and surrounding components, consistent with moisture intrusion or condensation from a compromised vent connection. Documented the corrosion, insulation wear, and wiring condition, and addressed the flue/vent connection to restore proper venting of combustion gases. Recommend monitoring the cabinet for continued corrosion and moisture, as the extent of rust may warrant further evaluation or future floor pan repair.

Performed boiler maintenance by flushing and refilling the hydronic heating system to remove sediment and debris from the loop. Cleaned the Y-strainer on the circulator pump supply piping to restore proper flow, then verified the system was refilled and operating normally with no visible leaks.

Removed the existing digital thermostat and installed the customer-supplied Honeywell smart thermostat on a new wall plate, connecting the control wiring at the terminals. Powered up the unit and verified the display, humidity reading, and heating call, with the system responding to a setpoint of 80°F.

Replaced valves on the boiler piping and responded to reported leaks at several of the new connections. Inspected the temperature/pressure gauge assembly and pressure-regulating valve, noting corrosion and residue at threaded joints and discoloration on the copper supply lines. Cause of the leaks is still undetermined and may require further testing, joint re-sealing, or replacement of the affected fittings.

Performed a replacement estimate on a 14-year-old Lennox 120,000 BTU 80% gas furnace with no heat due to a failed inducer motor, and quoted the repair. Inspected the closet installation and noted heavy debris and grime around the base of the unit, as well as frost and condensation buildup on the supply plenum ductwork, which warrants further evaluation of airflow and the 16x25x1 filter. Documented the equipment and conditions with photos and presented replacement options to the homeowner.

Performed maintenance and diagnostic service on a 12-year-old Lennox gas furnace reported to be short cycling and producing loud operating noises, with no service in the past two years. Inspected the blower assembly, gas valve, wiring, and filter compartment, and cleaned accumulated dust, debris, and dirt buildup from the cabinet interior and surrounding base area to restore proper airflow and combustion conditions. Verified system operation following service.

Performed an on-site estimate for a ductless mini split installation in a bedroom, evaluating potential indoor air handler placement and marking proposed mounting locations on the wall. Documented existing room conditions with photos to support equipment sizing and installation planning, and left a message with the customer to confirm the details.

Performed seasonal heating maintenance on an 8-year-old gas furnace, inspecting the blower motor and housing, gas valve, burner assembly, wiring connections, and control board, with no rust, frost, or visible damage found. Also verified operation of the Aprilaire humidifier control, which displayed a normal humidity reading of 57%.