HVAC, Plumbing & Electrical in Cuyahoga Falls, OH

Responded to service call for leaking water heater at cold water valve connections on an 8-year-old residential unit. Upon inspection, identified active leak at cold water inlet valve, tightened connections, and verified proper sealing of braided flex connector and copper piping joints to resolve the issue.

Responded to main drain backup issue at residential property. Upon arrival, performed camera inspection of main sewer line, revealing significant buildup and staining within the drain system. Inspected utility sink plumbing connections and floor drain assembly in basement area. Successfully cleared the clogged main drain line, restoring proper drainage function throughout the system.

Completed scheduled MVP cooling maintenance visit on residential air conditioning system. Inspected outdoor condenser unit and found finned coil surface with moderate accumulation of dirt, dust, and debris between fins, along with minor fin damage typical of outdoor exposure. Examined air filter and discovered heavy soiling with significant dust and debris buildup requiring attention. Documented equipment condition through photographs showing condenser coil deterioration and filter contamination levels. System components assessed for operational efficiency and maintenance requirements per recurring service protocol.

Completed comprehensive MVP cooling maintenance on Lennox outdoor condenser unit. Performed standard inspection of electrical components including capacitor, contactor, and wiring connections, verified all terminals secure and functioning properly. Unit exterior and coils inspected, system operating within normal parameters upon completion of maintenance service.

Completed scheduled furnace tune-up and maintenance for MVP customer. Performed comprehensive system inspection including visual examination of furnace components, burner assembly, heat exchanger, and blower motor. Utilized digital inspection camera to assess crawl space conditions and verify proper system installation and clearances. All components found operating within normal parameters, and system returned to full service.

Completed scheduled MVP cooling system maintenance visit at residential property. Performed comprehensive inspection of furnace and HVAC equipment, including visual assessment of draft hood, flue connections, and PVC condensate drainage lines. Conducted temperature diagnostics using thermal probe to verify proper system operation and efficiency. Inspected electrical wiring connections, flexible ductwork, and all accessible mechanical components to ensure safe and optimal performance for the cooling season.

Diagnosed leaking rear hose bib at packing nut on slab foundation property. Replaced outdated exterior faucet with new frost-free hydrant assembly including dedicated shut-off valve and supply piping. Cut access opening through interior wall behind dryer location and installed permanent access panel for future serviceability. Completed full installation with maintenance value plan coverage.

Completed maintenance visit program on an 11-year-old furnace system. Inspected and replaced heavily soiled air filter that showed significant dust accumulation, discoloration, and debris buildup affecting system airflow and efficiency. Performed standard heating system inspection and maintenance procedures to ensure optimal operation for the heating season.

Completed scheduled MVP maintenance on a 5-year-old furnace system. Performed comprehensive inspection of heating equipment, verified proper operation of all components, and confirmed system is functioning within manufacturer specifications. Unit is operating efficiently with no issues identified at this time.

Replaced defective hot side anode rod and nipple on one-year-old Bradford 40-gallon short water heater that was actively leaking. Installed new female adapter and slip coupling to complete the repair and restore proper function to the unit.

Completed scheduled MVP heating maintenance visit. Inspected and verified proper operation of electronic control panel and circuit boards, checked all electrical connections and wiring harnesses for secure termination, and performed standard system diagnostics to ensure optimal heating system performance for the upcoming season.

Completed comprehensive furnace maintenance on MVP heating system. Performed diagnostic testing using Fieldpiece dual port manometer to measure temperature differentials and system pressures, recording inlet temperature of 118.2°F and ambient temperature of 75.2°F. Utilized Fieldpiece SC680 clamp meter to verify electrical parameters including voltage, amperage, and resistance across motor and blower assembly. Inspected internal components including blower motor, heat exchanger, wiring harnesses, and gas valve connections. Verified proper operation of all mechanical and electrical systems, confirmed R-410A refrigerant labeling and safety warnings are present and legible. All components functioning within manufacturer specifications, no repairs required at this time.

Completed preventive maintenance on a 7-year-old gas furnace under the MVP heating maintenance program. Performed diagnostic measurements using digital manometer, recording gas pressure readings at 12.55" to verify proper combustion and system operation. Inspected blower motor assembly, electrical connections, gas valve terminals, and all associated components, confirming equipment is operating within manufacturer specifications with no deficiencies noted.

Completed comprehensive AC tune-up on 11-year-old cooling system for MVP member. Performed electrical testing using clamp meter to verify proper amperage draw and system performance, inspected contactor assembly and all electrical connections for secure termination and proper operation, and documented equipment condition through detailed photography. All components operating within manufacturer specifications at time of service.

Completed comprehensive furnace tune-up on 5-year-old unit. Performed standard maintenance procedures including inspection and cleaning of flame sensor, which showed mineral deposits and required removal for proper cleaning. All system components were inspected, tested, and verified to be operating within normal parameters.

Completed comprehensive MVP Heat maintenance service on heating system. Inspected and documented air filter condition, noting moderate dust accumulation and discoloration across filter media within air handler unit. Performed diagnostic measurements using digital testing equipment on HVAC components to verify proper system operation and performance parameters.

Performed inspection of 46-year-old toilet in basement to provide replacement estimate. Documented existing fixture condition, internal tank components, and surrounding bathroom area with photographs for accurate quote preparation. Customer requesting callback to schedule replacement service.

Installed a new American Standard Cadet Pro model toilet with round bowl and standard height in residential bathroom. Removed existing toilet fixture, prepared flange and mounting surface, set new two-piece toilet unit with proper wax ring seal, secured to floor, connected water supply line, and tested for proper operation and leaks. Installation completed successfully with all components functioning as specified.

Completed preventive maintenance tune-up on two residential air conditioning systems: an 11-year-old unit and a 1-year-old unit. Performed comprehensive inspection of both outdoor condensing units, including examination of condenser coils which were found to be in good condition with minimal debris accumulation and proper fin alignment. Both systems showed no operational issues or performance concerns at time of service.

Completed MVP recurring heating maintenance visit. Inspected blower wheel assembly and found dust accumulation on blades; assessed blower motor operation and verified proper function. Examined and tested flame sensor, confirming electrical connectivity and component integrity to ensure reliable system ignition and safe operation.